Leadshine DM2282-IO-24 User manual

Stepper drive with speed control DM2282-IO-24 easy manual

I/O Signals Connection

The I/O signals connections are as below, PUL signals indicate Start/Stop function, DIR signals indicate motor running direction, ENA

signals indicate lock the motor shaft (no need to be connected by default)

Control signals voltage is 24VDC.

DM2282-IO-24 2-phase Speed Control Stepper Drive

80-250VAC, 0.5-8.2A peak current, Auto-configuration, Low Noise

Motor Connection

DM2282-IO-24 can match with Leadshine 2-phase stepper motor, size include NEMA34, 42, 51

The motor connections are shown as below

4-lead Motor Connections 8-lead motor series connections 8-lead motor parallel connections

Features

External I/O signal control mode, with 24VDC

DIP switch setting drive’s output current and motor speed

PUL+ and PUL- signals indicate Start and Stop

DIR+ and DIR- signals indicate motor running direction

Alarm output, max 30Vdc / 100mA

Matched with NEMA 34, 42, 51 stepper motors

DM2282-IO-24 Interface

Power Supply Connection

Rang 80-250VAC, recommend L&N connect to

180-230VAC power supply, higher power voltage brings

better performance at high speed.

Recommend PE connect with the ground of equipment.

Power Supply

Power Ether

Status Indicator

FAULT-

FAULT+

ENA-

ENA+

DIR-

DIR+

PUL-

PUL+

SW1

SW2

SW3

SW4

SW5

SW6

SW7

SW8

I/O signals

Motor Power

A-

Tuning Port

B+

B-

A+

DIP Switch

Stepper drive with speed control DM2282-IO-24 easy manual

Caution

Be sure to read this manual carefully before trying to install and use the product.

Be sure to check the connections and make sure the power lead polarity is correct, or there could result in injury or

fire.

Be sure to ground the earth terminal of the motor and drive without fail, or there could result in electrical shock.

Be sure to mount the load after making sure the motor work well without load, or there could result in some

accident.

Be sure to turn off power and wait for 10 minutes or longer after LED display of the front panel has gone off, and

then you can transporting, wiring and inspecting the drive, or there could result in electrical shock or fire.

Be sure to install an emergency stop circuit externally so that you can stop the operation and shut off the power

immediately, or there could result in some accident.

Be sure to give the power supply voltage does not exceed the drive’s input range, or there could result in burning

out drive and motor.

Web: http://www.leadshine.com Sales: sales@leadshine.com Support: tech@leadshine.com

Peak

RMS

SW1

SW2

SW3

Default

off

2.2A

1.6A

off

3.2A

2.3A

off

4.2A

3.2A

off

5.2A

3.7A

off

6.3A

4.4A

off

7.2A

5.2A

off

8.2A

5.9A

Motor Speed (RPM)

SW5

SW6

SW7

SW8

100

150

off

250

off

350

off

450

off

550

off

650

off

750

off

850

off

950

off

1050

off

1150

off

1250

off

1350

off

1450

off

1500

off

DIP Switch Setting

●DM2282-IO-24 has 8-bit DIP switches, functions as below:

SW1

SW2

SW3

SW4

SW5

SW6

SW7

SW8

●Output current setting (3-bit) ●Motor speed setting (4-bit)

Dynamic output current

Motor speed

Holding current/Auto-tuning

Note：This drive is only suitable for long-term constant

speed applications, not for applications with frequent

speed adjustment.

●Holding current/Auto-tuning (SW4)

“Off” means holding current is 60% of dynamic current,

while “on” means 100%.

Switch “SW4” two times in two seconds will activate

parameter Auto-configuration for current loop.

Table of contents

Other Leadshine DC Drive manuals

Leadshine

Leadshine EM3E Series User manual

Leadshine

Leadshine EM415S User manual

Leadshine

Leadshine CS2RS-D503 User manual

Leadshine

Leadshine EM882S User manual

Leadshine

Leadshine DMA882S User manual

Leadshine

Leadshine DM1182 User manual

Leadshine

Leadshine EM870S User manual

Leadshine

Leadshine DM556E User manual

Leadshine

Leadshine ES2-3DA2306 User manual

Leadshine

Leadshine DM860E User manual

Leadshine

Leadshine CS1-D507S User manual

Leadshine

Leadshine 3DM883 User manual

Leadshine

Leadshine STEPPERONLINE DM320T User manual

Leadshine

Leadshine CS-D403 User manual

Leadshine

Leadshine EM422S User manual

Leadshine

Leadshine DMA860H User manual

Leadshine

Leadshine DM556E User manual

Leadshine

Leadshine EM556-CAN User manual

Leadshine

Leadshine MX3660 Assembly instructions

Leadshine

Leadshine DM Series Assembly instructions

Leadshine

Leadshine CS3E Series User manual

Leadshine

Leadshine EM522-CAN User manual

Leadshine

Leadshine DMA860E User manual

Leadshine

Leadshine EM3E Series User manual

Popular DC Drive manuals by other brands

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS user manual

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Technical description

Chamberlain Garog

Chamberlain Garog D Series operating manual

Parker

Parker PDS Series user guide

Festo

Festo DGC G Series Repair instructions

Binks

Binks QS-5012-1-CE Service manual

Danfoss

Danfoss VLT 2800 Series Quick setup

ABB

ABB ACQ580-01 Series Quick installation and start-up guide

YASKAWA

YASKAWA CANopen SI-S3 Technical manual

GE D20A6 instructions

Unex

Unex MC-D-250-1000-050W-TW operating manual

Geckodrive

Geckodrive G213V manual

ABB

ABB RSYC-01 user manual

Rockwell Automation

Rockwell Automation PowerFlex 700S Programming manual

WEG

WEG DeviceNet CFW500 user manual

Siemens

Siemens SINAMICS G List manual

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Operating instructions & installation instructions

SOMFY

SOMFY JR RU 30 instructions