LAVAZZA Bunn Nitron User manual

Table of contents

Other LAVAZZA Coffee Maker manuals

LAVAZZA

LAVAZZA LB 2801 User manual

LAVAZZA

LAVAZZA CLASSY PLUS User manual

LAVAZZA

LAVAZZA espresso point User manual

LAVAZZA

LAVAZZA LB COMPACT User manual

LAVAZZA

LAVAZZA LB 4200 User manual

LAVAZZA

LAVAZZA Jolie & Milk User manual

LAVAZZA

LAVAZZA BLUE LB 300 CLASSY MINI User manual

LAVAZZA

LAVAZZA ESPRESSO POINT MATINEE User manual

LAVAZZA

LAVAZZA Magystra LB 2600 INT Manual

LAVAZZA

LAVAZZA Jolie User manual

LAVAZZA

LAVAZZA EP800 User manual

LAVAZZA

LAVAZZA EP MINI User manual

LAVAZZA

LAVAZZA blue CLASSY CUSTOM MILK LB1050 User manual

LAVAZZA

LAVAZZA NEW Tiny ECO User manual

LAVAZZA

LAVAZZA LB 1000 BLUE FAMILY Operating manual

LAVAZZA

LAVAZZA OMNIA User manual

LAVAZZA

LAVAZZA Blue LB 2000 User manual

LAVAZZA

LAVAZZA EP950 User manual

LAVAZZA

LAVAZZA A MODO MIO User manual

LAVAZZA

LAVAZZA LB 4712 User manual

LAVAZZA

LAVAZZA OMNIA User manual

LAVAZZA

LAVAZZA Amodo MIO User manual

LAVAZZA

LAVAZZA CLASSY MINI User manual

LAVAZZA

LAVAZZA VOICY User manual

Popular Coffee Maker manuals by other brands

Taurus

Taurus Livorno 6 manual

Delta-q

Delta-q QUICK instruction manual

Bunn

Bunn LCA-1 Installation & operating guide

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Use and care book

Saeco

Saeco Vienna Plus Sup 018M operating instructions

DeLonghi

DeLonghi DC300 Owner's instructions

INCAPTO

INCAPTO BXCO1470E Instructions for use

Bosch

Bosch TASSIMO finesse TAS16B Series user manual

Exido

Exido 245-072 Specifications

Animo

Animo OptiVend Choco user manual

Siemens

Siemens TQ505DF Series user manual

DeLonghi

DeLonghi ECI341 Instructions for use

Krups

Krups KT406511 manual

Cimbali

Cimbali M32 Classic manual

Philips

Philips HL3844N Service manual

Bosch

Bosch TES 515 SERIES instruction manual

Tekmatix

Tekmatix TMFM - 65 Operation manual

Scarlett

Scarlett SC-CM33005 instruction manual

Bunn Nitron

Lavazza Ambient Cold Brew 7:1 Changes

Purpose:

Lavazza is changing the cold brew formula from the existing 5 to 1 refrigerated concentrate

to a 7 to 1 ambient concentrate. This ratio change requires adjustments to the Bunn Nitron

Cold Brew machine. Please follow the instructions below to make these changes. If you have

any issues or technical questions, please call 1-888-952-8299.

Tools Needed:

-250mL plastic graduated cylinder or ounces measuring cup.

oLink to Purchase on Amazon

-Straight Blade Screwdriver

Instructions:

1. Remove the cold brew and nitrogen spouts by turning them clockwise and then

pulling down. Confirm that the white nitrogen agitator is present in the left-side

spout and be sure to clean the agitator (please see picture below). Clean the right-

side cold brew spout. Using the food grade lubricant provided on the inside of the

door, lubricate the seals of the spouts, and reinstall them on the machine.

2. Unplug the Nitrogen module (usually located underneath of the cold brew machine).

3. Remove the drip tray and remove the two straight blade screws (circled in yellow in

the picture below). Once the screws are removed, pull out and down on the cover

exposing the circuit board.

4. Place the machine in programming mode using the switch in the bottom middle as shown in

the picture below.

5. Place your graduated cylinder underneath the nitrogen spout (left side spout) and pull the

nitrogen handle (left side handle) 3 times relatively quickly. You should hear a beep each

time you pull the handle, and a measurement of water will dispense into your measuring

cup. Dispose of the first sample and repeat (the second time, there should be no product

present, just water).

6. On the nitrogen side (left side), you should receive 133mL or 4 ½ ounces. If you received the

correct amount, move on to step 8. If your measurement was low or high move on to step 7

(From the factory, the water regulator located behind the right-side panel is set to this

measurement. In most cases, unless this was tampered with, step 7 should not be needed)

7. If your volume was low or high, remove the 4 screws in the corners of the right-side panel

and remove the panel. Locate the water volume regulator in the middle of the right-side.

Pull knob slightly to unlock adjustment. In quarter turn increments, turn clockwise to

increase, and counterclockwise to decrease volume. Do a volume test (step 5) after the

adjustment, and always remember to dispose of the first sample. After proper volume is

achieved, push knob back into place to lock position.

8. With the nitrogen side (left side) volume set at 133mL or 4 ½ ounces, now perform the same

volume test (step 5) on the cold brew (right side). Remember to dispose of your first

sample. This sample should also be around 133mL or 4 ½ ounces. If it is low or high, open

the door to the machine and locate the cold brew flow regulating screw, as seen in the

picture below.

Turning the screw in (clockwise) will decrease volume. Turning the screw out (counterclockwise)

will increase volume. Try to achieve a volume as close as possible to 133mL or 4 ½. It is ok to

have a volume on the cold brew (right side) between 127 mL to 139 mL, as the product chart in

step 11 allows for some variation.

9. Open the door to the machine and install your new 7 to 1 ambient cold brew bib.

10. Locate the four potentiometers (4 circular adjustment dials located above the programming

and compressor switch). We will only be using the two wheels on the left as shown in the

picture. The far left is the concentrate adjustment wheel for the Nitro side (left side) and

the one next to it is for the concentrate adjustment for the cold brew side (right side).

Each wheel has an arrow on it. Begin by setting the two adjustment dials arrows to the 10

o’clock position.

11. While still in programming mode, place your graduated cylinder underneath of the nitrogen

spout (left side spout) and pull the nitrogen handle (left side handle) 6 times relatively

quickly. You should hear a beep each time you pull the handle. A measurement of product

will dispense into your measuring cup. Dispose of the first sample and repeat (the second

time, there should be no water, just concentrate). Use the below chart to compare the

amount of concentrate that should be dispensed vs. the amount of water being dispensed.

For example, if your water volume for that tap was at 130mL, then the amount of product being

dispensed in step 11 should be 18.6mL. If the volume of concentrate is high, adjust that

potentiometer slightly counterclockwise and retest the volume. If low, turn slightly clockwise

and retest volume. Once you have the nitro side (left tap) set properly. Repeat this step for the

cold brew side (right tap).

12. Take the machine out of programming mode via the switch underneath of the control board.

Re-plug in the nitrogen generator and taste the product to ensure that it is correct.

13. Replace the front cover, re-install the two screws, and replace the drip tray. The Bunn Nitron

is now ready for use with the 7 to 1 product.

If you have any issues, please contact Lavazza Technical Services at 1-888-952-8299. Or go to

https://lavazzatechservices.com/lavazza-cold-brew-launch for information and how-to-videos.