Laserworld DISCO-300G User manual

DISCO-300G

USER MANUAL

Please read this manual carefully before use!

USER MANUAL: DISCO-300G

Date: 01/2008

Page

Table of contents

Page

1. SA ETY INSTRUCTIONS 3

2. OPERATING DETERMINATIONS 4

3. OPERATION 5

4. AUTO- MUSIC-MODE 5

5. OPERATION WITH DMX 5

6. ILDA OPERATION 7

7. MAINTENANCE 8

8. TECHNICAL SPECI ICATIONS 8

hecking Parts

Please check if the following parts are included:

1 x DISCO-300G Laser

1 x Power cable

1 x DMX cable

1 x ILDA adaptor

1 x User manual

USER MANUAL: DISCO-300G

Date: 01/2008

Page

DANGER LASER RADIATION!

Avoid direct eye exposure!

Laser radiation can cause eye damage and/or skin damage

All protective measures for a safe operation of this laser must be applied.

1. SAFETY INSTRUCTIONS

- If the device has been exposed to drastic temperature fluctuation, do not

switch it on immediately. The arising condensation water might damage your

device. Leave the device switched off until it has reached room temperature.

1. The laser must only be used for shows. The operation is only allowed if it is

controlled by a skilled and well-trained operator.

- Never leave this device running unattended and keep it away from children

and unauthorized persons.

2. Keep away from heaters and other heating sources. In order to safeguard

sufficient ventilation, leave 50 cm of free space around the device.

3. Never direct the laser beam to people or animals.

4. CAUTION LASER DIODE: Never unscrew the housing!

There are no serviceable parts inside the device. Maintenance and service

operations shall only be carried out by authorized dealers.

5. Always disconnect from the mains when the device is not in use or before

cleaning it.

- HEALTH HAZARD! Never look directly into the light source, as

sensitive persons may suffer an epileptic shock!

USER MANUAL: DISCO-300G

Date: 01/2008

Page

2. OPERATING DETERMINATIONS

6. The operator has to make sure that laser radiation – also reflected laser

radiation –higher than the highest allowed level is avoided by technical or

organisational measures.

7. Make sure that the used voltage is : AC 220V~240V, 50/60Hz

8. If the device is used in a flying installation, the mounting brackets and an

appropriate safety-rope must be fixed.

9. Laser effects are not designed for permanent operation. Consistent operation

breaks will ensure that the device will serve you for a long time without

defects.

10.In some countries, the operator must notify the accidence insurance and the

authority for industrial safety, before operating a laser. or more information,

contact the relevant authorities.

11.Please consider that unauthorized modifications on the device are forbidden

due to safety reasons!

12.If this device will be operated in any way differently than described in this

manual, the product may suffer damages and the guarantee becomes void.

urthermore, any other operation may lead to dangers like short-circuit,

burns, electric shock, etc.

13.When the laser is not attached to an ILDA output device (even for a short

period), switch ILDA mode off (see below), or turn the device off.

USER MANUAL: DISCO-300G

Date: 01/2008

Page

3. OPERATION

Please note: for sound/DMX mode the two switches on the back

of the device labelled “BLANKING” and “X/Y” have to be up.

When both switches are down the device can be controlled by

an ILDA output (such as our USB-Box). Use this switch setting

only when connected to such an ILDA controller. Even if you

disconnect/interrupt the ILDA connection only for a short

period, always put the switches into up position, or turn the

device off!

4. AUTO- MUSIC-MODE

If you put switch 10 to “ON” the patterns will change automatically, and are

animated by sound (sound or music mode), the switches labelled “BLANKING” and

“X/Y” have to be up. You can control the music-sensitivity of the microphone with

the min-max knob on the rear panel. With switch 1 you can select two modes:

standard sound mode (patterns will move triggered by sound), and animated sound

mode (patterns will move slowly without sound and will be accelerated with sound).

5. OPERATION WITH DMX

If you turn switch 10 to “O ”, and switches “BLANKING” and “X/Y” up, the device is

in DMX mode. Set the DMX address and connect the device to a DMX controller, you

can then operate you CS-200G ECO with DMX.

Set the DMX address code with the binary system “0” or “1”. A few examples:

DMX

adress

DMX

adress

113

161

USER MANUAL: DISCO-300G

Date: 01/2008

Page

The device uses 11 channels, so if you set the first on DMX address “1” the second

should be DMX address “12” and so on.

The DMX channels are as following:

channel Function

Mode: 0

69 laser off; 70

139

sound mod

; 140

209 animated sound mode (see above); 210-

255 DMX mode

Pattern

Effec

channe

l: Strobe

Horizontal movement: 0 no effect; 1

167 (fixed)

movement; 168-188 animated movement left to

right with increasing speed; 189-209 do. Right

to left; 210-255 do. left to right and back

ertical

movement

: analogous to hor. movem.

Zoom: 0

10 no effect; 11

104 increasing size;

105-154 growing with increasing speed; 155-

204 do. shrinking; 205-255 do.

growing/shrinking

Width (rotation about y): 0

150 fixed rotation;

151-255 automatic rotation with incr. speed

Height (rot. About X): analogous to width

Rotation: 0

180 fixed rotation; 181

217

automatic with incr. speed clockwise; 218-255

do. counter clockwise

Blanking: 0

70 no effect; 71

139 points are

brighter; 140-209 dashed lines; 210-255 points

only

Wave

Please note that according to the pattern, not all effect channels are

activated. E.g. you can’t zoom dynamic patterns, etc.

Channel 3 (strobe) is also available when in soundmode (channel 1 70-209).

USER MANUAL: DISCO-300G

Date: 01/2008

Page

6. ILDA OPERATION

Connect the laser to an ILDA output (as our USB-box) using the adaptor shipped

with the device, switches “BLANKING” and “X/Y” on the back of the laser have to be

down. You can now operate the laser with ILDA.

Use this switch setting only when connected to an ILDA

controller. Even if you disconnect/interrupt the IDLA connection

only for a short period, always put the switches into up position,

or turn the device off.

You can now control laser output with a PC, using for example our ShowEditor 2006

software. Laserworld offers a variety of music synchronous lasershows for

ShowEditor 2006.

USER MANUAL: DISCO-300G

Date: 01/2008

Page

7. MAINTENANCE

Maintenance should be performed every 15-day period, by using a sponge which is

dipped with alcohol, rather than wet cloth or other chemical liquid, to clean the

mirror.

Always disconnect from the mains when the device is not in use or before cleaning it.

There are no serviceable parts inside the device. Maintenance and service operations

are only to be carried out by authorized dealers.

Never look directly into the light source.

Always disconnect from the mains when the device is not in use or before

cleaning it.

8. TECHNICAL SPECIFICATIONS

Power supply: AC 220V-240V, 50/60 Hz

DMX 512: 11 channels

Ambient temperature: -10°C – +35°C

Power consumption: 40 W

Working mode: automatic, music active, DMX512, ILDA

Optical power: ca. 300mW / 532nm

Laser classification: 3b

Weight: 4 kg

Dimensions: 300 x 240 x 130 mm

PLEASE NOTE

This device has left our premises in absolutely perfect condition. In order to maintain

this condition and to ensure a safe operation, it is absolutely necessary for the user

to follow the safety instructions and warning notes written in this user manual.

Laserworld cannot be made liable for damages caused by incorrect installations and

unskilled operation!

USER MANUAL: DISCO-300G

Date: 01/2008

Page

EU- Declaration of onformity

We hereby confirm that the following device

DIS O-300G

complies with the essential safety requirements, laid down in the regulations of the

committee to assimilate the provisions of law of all participating EU states on the

electromagnetic compatibility (98/336/EWG).

The device has been classified considering the following EU-norms on

electromagnetic compatibility:

DIN EN 55103-1: 1996

DIN EN 55103-2: 1996

DIN EN 61000-3-2:2000 + A2: 2005

DIN EN 61000-3-3:1995 + A1: 2001

Assessment of compliance of the product with the requirements relating to the Low Voltage

Directive (LVD) was based on the following standards:

DIN EN 60065 : 2002

urthermore, the device is verified in correspondence to the laser class regulations DIN EN

60825-1, if properly set up according to the upper mentioned laser safety regulation.

After installing the device, an inspection and official approval is indispensable for the overall

setup. The inspection must follow the european guidelines EN 60825-1 and corresponding

regulations for the prevention of accidents BGV-B2.

This declaration is executed on behalf of the DISCO-300G Laser manufacturer.

Laserworld (Switzerland) AG

Oberstrasse 1

8274 Tägerwilen

SWITZERLAND

Authorized person:

Supervisory board Ms Rhea Gössel

place of business: 8274 Tägerwilen / SWITZERLAND

company number: CH-440.3.020.548-6

Commercial Registry Kanton Thurgau

www.laserworld.com

info@laserworld.com

representative according to EMVG:

Cleantech Europe GmbH

Managing Director: Thomas Schulze

ürkhofstr. 5

81927 München / DE

Table of contents

Other Laserworld Lighting Equipment manuals

Laserworld

Laserworld LW-50k User manual

Laserworld

Laserworld BLUE-400-445 User manual

Laserworld

Laserworld EL-200 RGY User manual

Laserworld

Laserworld Garden Star Series User manual

Laserworld

Laserworld PL-12.000G User manual

Laserworld

Laserworld GREEN-12000 User manual

Laserworld

Laserworld Club Series User manual

Laserworld

Laserworld Evolution ES-800RGB User manual

Laserworld

Laserworld BeamBar 10R-638 User manual

Laserworld

Laserworld Evolution Series ES-400RGB User manual

Laserworld

Laserworld Club Series User manual

Laserworld

Laserworld EL-50G DMX User manual

Laserworld

Laserworld tarm Series User manual

Laserworld

Laserworld Garden Series User manual

Laserworld

Laserworld GREEN-150E User manual

Laserworld

Laserworld RS 400 G US User manual

Laserworld

Laserworld GREEN-4000 User manual

Laserworld

Laserworld LW25K User manual

Laserworld

Laserworld PL-16.000RGB User manual

Laserworld

Laserworld EL-60 G User manual

Laserworld

Laserworld GREEN-100E User manual

Laserworld

Laserworld V PRO-OEM User manual

Laserworld

Laserworld RS 800 G User manual

Laserworld

Laserworld GREEN-5000 User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions

Silvair

Silvair MESH-CEDRP quick start guide