Laserworld CS-100G User manual

CS-100G

USER MANUAL

Please read this manual carefully bef re use!

USER MANUAL: Laserworld CS-100G

Date: 01/2008

Page

Checking Parts

Please he k if the following parts are in luded:

1 x CS-100G Laser

1 x Power able

1 x DMX able

1 x Interlo k plug

1 x User manual

USER MANUAL: Laserworld CS-100G

Date: 01/2008

Page

DANGER LASER RADIATION!

Avoid dire t eye exposure!

Laser radiation an ause eye damage and/or skin damage

All prote tive measures for a safe operation of this laser must be applied.

1. SAFETY INSTRUCTIONS

- If the devi e has been exposed to drasti temperature flu tuation, do not

swit h it on immediately. The arising ondensation water might damage your

devi e. Leave the devi e swit hed off until it has rea hed room temperature.

1. The laser must only be used for shows. The operation is only allowed if it is

ontrolled by a skilled and well-trained operator.

- Never leave this devi e running unattended and keep it away from hildren

and unauthorized persons.

2. Keep away from heaters and other heating sour es. In order to safeguard

suffi ient ventilation, leave 50 m of free spa e around the devi e.

3. Never dire t the laser beam to people or animals.

4. CAUTION LASER DIODE: Never uns rew the housing!

There are no servi eable parts inside the devi e. Maintenan e and servi e

operations shall only be arried out by authorized dealers.

5. Always dis onne t from the mains when the devi e is not in use or before

leaning it.

- HEALTH HAZARD! Never l k directly int the light s urce, as

sensitive pers ns may suffer an epileptic sh ck!

USER MANUAL: Laserworld CS-100G

Date: 01/2008

Page

2. OPERATING DETERMINATIONS

6. The operator has to make sure that laser radiation – also refle ted laser

radiation –higher than the highest allowed level is avoided by te hni al or

organisational measures.

7. Make sure that the used voltage is : AC 220V~240V, 50/60Hz

8. If the devi e is used in a flying installation, the mounting bra kets and an

appropriate safety-rope must be fixed.

9. Laser effe ts are not designed for permanent operation. Consistent operation

breaks will ensure that the devi e will serve you for a long time without

defe ts.

10.In some ountries, the operator must notify the a iden e insuran e and the

authority for industrial safety, before operating a laser. For more information,

onta t the relevant authorities.

11.Please onsider that unauthorized modifi ations on the devi e are forbidden

due to safety reasons!

12.If this devi e will be operated in any way differently than des ribed in this

manual, the produ t may suffer damages and the guarantee be omes void.

Furthermore, any other operation may lead to dangers like short- ir uit,

burns, ele tri sho k, et .

13.When the laser is not atta hed to an ILDA output devi e (even for a short

period), swit h ILDA mode off (see below), or turn the devi e off.

USER MANUAL: Laserworld CS-100G

Date: 01/2008

Page

Thank you for pur hasing our CS-100G laser proje tor. In order to use this produ t

safely and throughtly. Please read over this manual arefully before any

operation,the operation must a ording to manual stri tly to avoid any personal hurt

or produ ts damage . Any problem ex lude in this manual please onta t us!.

Specificati n

Model Referen e# LP-209

Components

Laser proje tor×1

Power able×1

DMX512 able×1

Interlo k 9pin plug×1

Laser key×2

Using voltage

AC 110V~230V，50/60Hz

Voltage of input signal -10V ~ +10V

Control Mode Auto/AUDIO/DMX/ILDA(optional)

DMX hannel 12

S anning system 20KPPS

Lasers&Power

Green laser : 532nm/ 75~100mW

Operating temperature 10° ~ 40°

Dimension(mm) 280(L)×200(W)×150(H)

Weight(kg) 3

Safety fuse 250V / F2A Φ5×20mm

ATTENTION&MAINTENANCE

1. Do not dis onne t the devi e without professional instru tion

2. Keep surrounding dry and lean.this unit should be keep dry, do not use in the

rain or dank and dusty environment. Proje tor should be overed with water-

proof when operate at outside.

3. Keep surrounding temperature at15~30,Remain 10minutes for equipment

ooling after 2 hours ontinuously work,or laser expe ted time will be

redu ed.

4. Distan e between lasing aperture and proje ted item should not be less than 1

meter.

5. Do not turn devi e on/off frequently to avoid broken.

6. Do not look into the laser beam dire tly,or view laser beam dire tly with

opti al instruments.

7. Do not tou h the devi e with wet hands.

8. Turn off the power before installation and maintenan e.

9. When the laser diode be ame dim or broken, please onta t the dealer timely.

10.To use the original pa kage when transport again and to avoid shake.

USER MANUAL: Laserworld CS-100G

Date: 01/2008

Page

11.Maintenan e should be performed every 15-day period, by using a sponge

whi h is dipped with al ohol, rather than wet loth or other hemi al liquid, to

lean the mirror.

WARNING & SAFETY

Class IIIblaser produ ts

Power output from 5 milliwatts to 500 milliwatts. These lasers are onsidered a

definite eye hazard, parti ularly at the higher power levels, whi h WILL ause eye

damage. So these laser series models supplied with a key swit h to prevent

unauthorized use, warning labels and aperture labels affixed to the laser.

Installation safety

Prior to installation and operation of the laser, the paths of the beams and effe ts

should be onsidered, parti ularly with respe t to how they will tou h the audien e.

If dire t audien e s anning is desired then the laser energy in the effe ts needs to be

onsidered to de ide if the effe ts are safe for dire t viewing.

INSTALLATION

1,Ba k panel instru tion

USER MANUAL: Laserworld CS-100G

Date: 01/2008

Page

1: ON/OFF(Power input with inner fuse)

2: REMOTE---------Interlo k (pin 1,2), onne t to emergeny swit h, or use interlo k

plug

3: DIP swit hes, referen e to DMX Control Mode as below.

4: DMX IN/OUT

5: AUDIO-------- Tune the sensitivity of sound a tivation(H),MAX→high sensitivity;

MIN→low sensitivity.

6: MIC(mi rophone).-------- To re eive sound a tivated signal

7: LASER--------Turn lasers ON or OFF.

8: ILDA--------DB-25 Female

Operati n M de Instructi n:

A. Sound A tive

Referen e to DIP swit h as below to hoose this mode.

B. Auto

In ludes Auto mode-Auto and Auto mode-Animal, referen e to DIP swit h as below.

C. DMX Control Mode

The first part is DIP address ode referen e, follow this to hoose the mode you

need.

DIP swit h:

Address 1-10 Pin,(1:ON,0:OFF,x:ON or OFF)

Address ode Cal ulate,When the mode is DMX ontrol:

x x x x x x x x x 1

1 2 4 8 16 32 64 128 512 DMX ontrol

when address is 1000 0000 01

this mean is 1 x 1=1, the same you must sele t DMX hannel 1 as the Start hannel,

DMX hannel 25 as the End hannel

when address is 0100 1000 01

this mean is 1 x 2 + 1 x 16=18, the same as above,sele t DMX hannel 18 as the

Start hannel, DMX hannel 42 as the End hannel.

1 ~ 10 Mode

0,0,0,0,0,0,0,0,0,0 Auto mode-Sound

1,0,0,0,0,0,0,0,0,0 Auto mode-Auto

1,1,0,0,0,0,0,0,0,0 Auto mode-Animal

0,0,1,0,0,0,0,0,0,0 Slave

x,x,x,x,x,x,x,x,x,1 DMX ontrol

USER MANUAL: Laserworld CS-100G

Date: 01/2008

Page

DMX Channel Instru tion----------12CHS single/three olor

Please refer to appendix1

D. ILDA M de

This laser proje tor has designed with a ILDA automati swit hing feature.ILDA

mode will be a tive when the pin-25 female(on the rear panel) was be onne ted.

All outputs are lo ated at an ILDA-standard onne tor (In and Out). This an be a

25-pin D-Sub onne tor(female) or a 25-pin IDC- onne tor(male).

The IDC- onne tor allows to onne t a separate D-Sub onne tor by using a flat

able. All outputs are symmetri al and be used in 3 different onfigurations:

1. symmetri al signal. Outputs + and – are onne ted dire tly with the

orresponding pins of the re eiving unit. For signal inversion, the 2 lines just have

to be rossed.

2. Single ended. Output – will be grounded to 0V (GND) and the outputs + and

GND have to be onne td to the inputs of the re eiving unit.

3. Single ended inverted. Output + is grounded to GND and the outputs – and

GND are onne ted to the inputs of the re eiving unit.

The maximum signal level between the s anneroutputs X and Y is 10V and the

signal level between, the oloroutputs is 5V.

All outputs an be grounded and are short ir uit prote ted.

USER MANUAL: Laserworld CS-100G

Date: 01/2008

Page

ILDA-standard c nnect r 25/26-pin

1 X+ S anneroutput +

2 Y+ S anneroutput +

3 Intens+ Intensity/Blanking +

4 Interlo k A Internally onne ted to 17

5 Red + Coloroutput Red +

6 Green + Coloroutput Green +

7 Blue + Coloroutput Blue +

8 – 12 n. . Not used

13 Shutter +5V *

14 X- S anneroutput –

15 Y- S anneroutput –

16 Intens- Intensity/Blanking –

17 Interlo k B Internally onne ted to 4

18 Red - Coloroutput Red -

19 Green - Coloroutput Green -

20 Blue - Coloroutput Blue -

21 – 24 n. . Not used

25 GND Signal ground

26 n. not used (IDC- onne tor only)

* Note: maximum load 20mA for 5V!

USER MANUAL: Laserworld CS-100G

Date: 01/2008

Page

Appendix1

12CHS DMX INSTRUCTION

CHANNEL# DMX

Value

Functi n

0~49 Auto mode---Sound

50~99 Auto mode---Auto

100~149

Auto mode---Graphi

150~199

Manual mode---Sound

1) C ntr l

m de

200~255

Manual mode---Auto

0~15 Laser off

16~25 No Blanking

26~135 Wave Blanking,Speed from 0 to27 (4)

136~245

Flash blanking,Speed from 0 to 27 (4)

2) Blanking

246~255

Fixed Blanking

3) Pattern 0~255 249 Pattern sele t

0~127 Manual Verti al Move

128~191

Auto Down Move,Speed from 0 to 16 (4)

4)Vertical

m ving 192~255

Auto Up Move,Speed from 0 to 16 (4)

0~127 Manual Horizontal Move

128~191

Auto Right Move,Speed from 0 to 16 (4)

(re ommend adjust 4 hannel and 13 hannel )

5) H riz ntal

M ving

192~255

Auto Left Move,Speed from 0 to 16 (4)

(re ommend adjust 4 hannel and 13 hannel )

0~127 Manual Vertical Roll

6) Vertical

R lling 128~255

Auto Vertical Roll,Speed from 0 to 16 (8)

0~127 Manual Horizontal 7) H riz ntal

R lling 128~255

Auto Horizontal Roll,Speed from 0 to 16 (8)

0~127 Manual Rotation

128~191

Auto lo kwise rotation,Speed from 0 to 16 (4)

8) R tati n

192~255

Auto anti- lo kwise rotation,Speed from 0 to 16 (4)

0~85 Auto from small to large,speed from 0 to 18 (5)

86~170 Auto from large to small,speed from 0 to 18 (5)

9) Z m

171~255

Auto Zoom by turns,speed from 0 to 18 (5)

10) Pattern

Size 0~255 The size from 0 to 255

11) D t view 0~255 0 Normally,Dot view from 1 to 10 (24)

0~127 Auto Slow draw A, speed from 0 to 21 (6) 12) Sl w

draw 128~255

Auto Slow draw B,speed from 0 to 21 (6)

PLEASE NOTE

This devi e has left our premises in absolutely perfe t ondition. In order to maintain

this ondition and to ensure a safe operation, it is absolutely ne essary for the user

to follow the safety instru tions and warning notes written in this user manual.

Laserworld annot be made liable for damages aused by in orre t installations and

unskilled operation!

Table of contents

Other Laserworld Lighting Equipment manuals

Laserworld

Laserworld Ecoline Series User manual

Laserworld

Laserworld Club Series User manual

Laserworld

Laserworld EL-60 G User manual

Laserworld

Laserworld RB-1.5 User manual

Laserworld

Laserworld GREEN-250A User manual

Laserworld

Laserworld CS-150G DMX User manual

Laserworld

Laserworld FX Series User manual

Laserworld

Laserworld Ecoline Series User manual

Laserworld

Laserworld GREEN-1500 User manual

Laserworld

Laserworld PRO-600R-640 User manual

Laserworld

Laserworld Ecoline EL-200RGB User manual

Laserworld

Laserworld Evolution Series User manual

Laserworld

Laserworld GREEN-5000C User manual

Laserworld

Laserworld PL-4000RGB User manual

Laserworld

Laserworld EL-120 R User manual

Laserworld

Laserworld EL-200S DMX User manual

Laserworld

Laserworld GREEN-75 User manual

Laserworld

Laserworld EL 200 LED User manual

Laserworld

Laserworld GREEN-300E User manual

Laserworld

Laserworld EL-400RG User manual

Laserworld

Laserworld CS-4000RGB FX MK2 User manual

Laserworld

Laserworld Evolution Series ES-800S RGB 3D Assembly instructions

Laserworld

Laserworld EL-60 G User manual

Laserworld

Laserworld PL-20.000RGB CT User manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions

Silvair

Silvair MESH-CEDRP quick start guide