Viewing Area 92×42mm
Cartridge Size 110×90mm
UV/IR Protection UP to shade DIN 16 at all times
Light State/Grind Mode DIN 4
Dark State Variable shade, DIN 9 ~ 13
Switch Time 1/2,5000S, from Light to Dark
Dark to Light Time/Delay Control
0.1-1.0S, by infinitely dial knob
Sensitivity Control Low - High, by infinitely dial knob
Power Supply
Solar cell and non-replaceable lithium battery
Power On/Off Fully automatic
Arc Sensor 2
TIG AMP Rating DC≥10, AC≥10
Operating Temperature -5°C to +55°C
Storing Temperature -20°C to +70°C
Compliance
DIN EN 379:2009-07, DIN EN 175:1997-08
Safety
ARC Rays can injure eyes
and burn skin
• Before welding, always
inspect helmet and auto-
darkening filter (ADF) to be
sure they are fitted properly
and in good condition.
• Keep the sensors, solar
cell and filter lens clean. Clean the filter cartridge using a
soapy water solution and soft cloth. Do not use solvents or
abrasive cleaning detergent.
• Donotweldintheoverheadpositionwhileusingthishelmet.
• Inspect the lter lens frequently and immediately replace
any scratched, cracked, or pitted filter lens or cover lenses.
• Always wear safety glasses or goggles under the welding
helmet, and protective clothing to protect your skin from
radiation, burns and spatter.
Specifications
Operation
Headgear Adjustment
1. Adjust the headgear diameter with
the twist knob on the back. The
knob is locked until pushed in.
Once unlocked, twist clockwise to
tighten and counterclockwise to
loosen.
2. Adjust the height by snapping the
pin into the hole to lock securely
in place.
3. To adjust the viewing angle,
loosen the knob and push the helmet forward and back to
the desired tilt position. Once the angle is correct, tighten
the knobs until snug. The helmet should still swing up, but
it should not drift downward when in place for welding.
4. To adjust the distance between the user’s face and ADF,
loosen the outside tension knobs to allow for headgear to
be repositioned to a different location. This should be done
one side at a time and both sides should be located the
same for proper auto-darkening filter operation.
Shade Control/Grind Mode
Select the shade 9 to 13 based upon the welding process
you will use by consulting the “Shade Guide Table”. The
variable shade control knob is mounted to shell for external
adjustment.
The welding helmet can also be used to protect the face when
grinding. Grind mode prevents filter lens from auto-darkening.
Delay Control
When welding ceases, the viewing window automatically
changes from dark back to light but with a pre-set delay to
compensate. The delay time can be set to MIN (0.1 sec) or
MAM (1.0 sec), by infinitely dial knob inside the cartridge. The
minimum delay suits spot or short welds. The maximum delay
suits heavy current welding and reduces eye fatigue from the
arc. Selections between MIN and MAX are suitable for most of
indoor and outdoor welding operations.
Sensitivity Control
The sensitivity can be set to LOW or HIGH by using the infinitely
dial knob on the back of the cartridge. The LOW setting suits
excess ambient light or with another welding machine close
by. The HIGH setting suits low amperage welding and welding
in areas with low light conditions, especially low amperage
argon arc welding. Selections between LOW and HIGH are
suitable for most of indoor and outdoor welding operations.
Operation
Front Cover Lens Replacement
Replace the front cover lens if it is damaged (cracked,
scratched, pitted or dirty). Place your finger or thumb into the
recess in the bottom of frame and flex the front cover lens
upwards until it releases from one edge. Then remove any
protective film before installing the new one.
Inside Cover Lens Replacement
Replace the inside cover lens if it is damaged (cracked,
scratched, pitted or dirty). Place your finger or thumb into
the recess as marked below and flex the inside cover lens
upwards until it releases from one edge. Then remove any
protective film before installing the new one.
Cleaning and Storing
Keep the sensors, solar cell and filter lens clean. Clean filter
cartridge and helmet shell by using a soapy water solution and
soft cloth. Do not use solvents or abrasive cleaning detergent.
Switch the product to Grind Mode and put it in a clean, dry
location for storage.
