Larson Electronics EPS-SW1-ESTP User manual

EPS-SW1-ESTP

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 1of 2

Explosion Proof Switch w/ E-stop

C1D1/C2D1 - Tumbler Switch, (1) E-Stop PB - Double Gang Box

Instruction Manual

Thank you for your purchase of the Larson Electronics EPS-SW1-ESTP.

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CRITICAL SAFETY INSTRUCTIONS:

•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY

RELEVANT LOCAL BUILDING CODES.

•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL

SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.

•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP

OBJECTS. SUITABLE FOR DAMP LOCATIONS.

WARNING

TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,

INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL

APPLICABLEELECTRICAL CODES.

TO AVOIDELECTRIC SHOCK:

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING

CONDUCTOR.

TO AVOID EXPLOSION:

•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.

•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS

ATMOSPHERE.

•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT

NAMEPLATE.

•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR

DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.

•ALL FASTENERS SHOULD BE PROPERLY SEATED.

IMPORTANT SAFEGUARDS; READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

1) Do not use this equipment other than the intended use as specified on the equipment nameplate.

2) Turn OFF the supplying circuit before beginning installation or performing any maintenance.

3) Service should be performed by qualified service personnel.

4) All installations must comply with the applicable local and/or National Electrical Code.

(Note: In the orientation of the enclosure (box & cover), the “TOP” is considered to be at the location of the cast-in part

numbers.)

The Larson Electronics EPS-SW1-ESTP Explosion Proof Switch is suitable for motor and electrical control in flammable

work sites. The 20-amp device features an on/off tumbler switch and one, emergency-stop mushroom push button. This

NEMA-rated unit is constructed of non-sparking aluminum and takes on a double-gang box configuration.

EPS-SW1-ESTP

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 2of 2

WIRING

Standard pigtail(flying leads) wiring

We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas

where weatherproofing may be required. Universal voltage driver permits operation at 120-277V AC.

Warning: Check product label for correct input voltage!

Attach supply line wires to the appropriate light fixture wires as shown

in thediagram 

Secure each pair of wires according to the diagram. Utilize ajunction box or

similar device and take precautionary steps for weatherproofing all

connectionsif installed in alocation where water may come in contact with the

unit. Ensurethe unit is properly grounded and that wiring is done according to

all local and national electrical/building codes.

•Disconnect power running to the unit and be sure the fixture iscool to the touch.

•Use a non-abrasive cleaning solution to clean the unit.

USE AND CARE

Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.

Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of

children when not in use.Inspect for good working condition prior to storage and before re-use.

REPLACEMENT PARTS

The EPS-SW1-ESTP is designed to provide years of reliable performance. Should the need for replacement parts arise,

please contact Larson Electronics.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

MAINTENANCE

There are no serviceable parts inside the fixture. However, itis good practice to routinely clean and check the

fixture for proper function.

INSTALLATION:

1) Install non-fused disconnect of your choice on din rail and align per instructions on page 3.

2) Install the two end blocks (provided) onto the din rail. Secure the blocks permanently on both sides of disconnect

by using a screw driver and tightening the recessed screws.

3) Cut “square shaft” provided, to the over-all length dimension shown in the chart on page 2, for the specific device

being used. (NOTE: smooth out the cut edge of the shaft)

4) Insert “square shaft bracket” into disconnect device interface opening per the orientation shown in the

picture on page 2.

5) Insert thecut shaft thru the square hole in the bracket, allowing it to rest at the bottom of the device interface

opening and in the orientation shown in the picture on page 2.

6) Terminate incoming cables to the line and load side of disconnect (field installation only).

7) Assemble cover on box making certain that the cross pinin the square shaft is engaged in the slot of the

operator in cover.

8) Tighten cover bolts.

Table of contents

Other Larson Electronics Switch manuals

Larson Electronics

Larson Electronics EPSW-3PH-20 User manual

Larson Electronics

Larson Electronics EPS-2XPB-SG-600V-LKC User manual

Larson Electronics

Larson Electronics EXP-EL-CSS-250A-R1-NO User manual

Larson Electronics

Larson Electronics EPS-3PSW-MMS User manual

Larson Electronics

Larson Electronics MPD-DS-WM-FDS Series User manual

Larson Electronics

Larson Electronics GAU-SW-4P-WW-24V User manual

Larson Electronics

Larson Electronics VPLHL-7WLED-50-NP User manual

Larson Electronics

Larson Electronics EPS-10HP-3PST User manual

Larson Electronics

Larson Electronics EPCS-PB10-2XMPB-2PS-N4X-M1 User manual

Larson Electronics

Larson Electronics EPS-PB10-MS-SPDT User manual

Larson Electronics

Larson Electronics GAU-125V-20A-P User manual

Larson Electronics

Larson Electronics EPS-PB10-GRN-2XC User manual

Larson Electronics

Larson Electronics EPS-PB10-2XC-M2-YR User manual

Larson Electronics

Larson Electronics EPL-SW Series User manual

Larson Electronics

Larson Electronics LED-ILS User manual

Larson Electronics

Larson Electronics EPS-PB10-MS-AT-N4X-V3 User manual

Larson Electronics

Larson Electronics EPS-DCSW-50A-600V User manual

Larson Electronics

Larson Electronics EPS-PB10 User manual

Larson Electronics

Larson Electronics EPS-PB20 User manual

Larson Electronics

Larson Electronics EPS-PB10-MS-AT-V4 User manual

Larson Electronics

Larson Electronics EPCS-PL-2X-RG User manual

Larson Electronics

Larson Electronics EPS-2XPB-SG-DPMS User manual

Larson Electronics

Larson Electronics EXHL-TRN-LE1 Series User manual

Larson Electronics

Larson Electronics PDU-ATS-100A-208Y.120-3PH User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual