LahZit D220 SPH Instruction Manual
USER & SAFETY MANUAL
LOG PEELER TOOL D220 SPH / PLR
ATTENTION! The cutting blades of this power tool are very sharp!
We suggest you read this information before you begin to
use this product. To use this product safely, always follow
general requirements and safety rules!
www.lahzit.ee
GENERAL REQUIREMENTS AND RECOMMENDATIONS
1. Usable 9’’ (230mm) angle grinder’s rated power must be at least 2000 W (watts), optimal spindle
speed is 6000 min-1, max spindle speed 6600 min-1.
2. The log peeler disc (figure 1, pos. 1) must be fixed to the angle grinder with standard (22.23 mm,
7/8’’) disc flange (figure 2, pos. 5) and clamp nut M14 (figure 2, pos. 4). Ensure that the clamp
nut’s step edge is directed towards the tool’s fixing hole. Clamp nut must be tightened with a
special angle grinder’s wrench, but it is important to use gloves, because there is a risk to injure
operator’s hand against the cutting blades, when the wrench should be accidentally slipping
away. Please be very careful!
3. Always disconnect the tool from the power source when changing cutting blades (figure 1, pos, 2)
or when performing any general maintenance activities (such as adjusting or cleaning).
4. Handle cutting blades with care. After sharpening, the blades can injure hands –therefore always
use gloves! Sharpening information is shown in figure 4 and figure 5.
5. Cutting blades must be adjusted according to processing requirements - the thicker bark of log
requires to adjust larger cutting depth (up to 3.0 mm), the wood surface finishing needs
adjustment of blades to 0.5…1.0mm. Make sure that the cutting blades are equally adjusted
(figure 3).
6. Ensure that cutting depth and screws M6x12 ISO7380 (figure 1, pos. 3) are tighted. Screws must
be tightened up to the torque 9.0 Nm (79.7 In. Lb. or 6.64 Ft. Lb.). Please use ¼’’ Torx T30
screwdriver bit, which included to the set of log peeler tool.
7. It is not allowed to start the angle grinder with not correctly tightened cutting blades!
8. If there are some deviations from the normal product operation (strange noise, vibration, loose
cutting blade), you must stop the machine immediately!
Fig. 1 Complete log peeler tool
Fig. 2 Mounting sheme of log peeler tool D220
SPH / PLR to the 9’’ (230 mm) angle grinder
Fig. 3 Principle of peeler tool D220 PLR cutting blades adjusting. The same principle applies for model
D220 SPH
Fig. 4 Sharpening angles for log peeler D220 SPH / PLR blades
Fig. 5 Dimensions of peeler D220 SPH / PLR cutting blades
SAFETY RULES
Always start peeling (debarking) operation with rotating peeler disc.
During operation always hold the angle grinder securely with two hand.
Do not remove workpiece or cut-off pieces from tool during a cut while the peeler disc is
rotating.
Do not leave tool until it comes to a complete stop.
Wear proper eye/ear protection. Everyday eyeglasses have only impact-resistant leses;
they are not safety glasses. Also use a face or dust mask if log peeling operation is dusty.
Visitors should wear the same protection.
We recommend to use special designed extra protective cover Lahzit®PC-D230, which can
be ordered from our company’s webshop www.lahzit.ee.
Use proper work gloves and anti slip security shoes
Avoid wearing clothing with loose sleeves.
When tool is not in use, please store it safely in original plywood box in dry storage. We
reccomend to keep peeler’s blades sharp and to process them with conservation oil. This
helps to prevent corrosion damages.
Producer and contact:
LAHZIT OÜ
Registration code 12614575
Vana-Koidu st 4, Elva EE-61507, Estland / Estonia
+3725105184
toomas.laatsit@lahzit.ee
www.lahzit.ee
This manual suits for next models
1
Table of contents
Other LahZit Power Tools manuals
