laguna DriftMaster User manual
DriftMaster Fence System
Manual
LAGUNA TOOLS
2072 Alton Parkway
Irvine, California 92606
Ph: 800.234.1976
www.lagunatools.com
Model Number: ABAND1000-0180
© 2017, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved.
3
Table of contents
Page number
Safety Rules
4
Limited warranty
5
Specification sheet
6
Receiving your drift master
6
Introduction to the drift master
6
Parts of the drift master
7
Unpacking your drift master
9
What you will receive with the drift
master
10
Assembly and setup
11
Using the drift master
20
Drift master controls
22
Adjusting the fence for drift
25
Maintenance
27
Exploded view drawings and parts lists
28
4
Safety Rules
As with all machinery, there are certain hazards involved with the
operation and use. Using it with caution will considerably lessen the
possibility of personal injury. However, if normal safety precautions are
overlooked or ignored, personal injury to the operator may result. If you
have any questions relative to the installation and operation, do not use the
equipment until you have contacted your supplying distributor.
Read the following carefully before operating the machine:
1. Keep the working area clean and be sure adequate lighting is
available.
2. Do not wear loose clothing, gloves, bracelets, necklaces or
ornaments. Wear face, eye, respiratory and body protection devices
as indicated for the operation or environment.
3. Be sure that the power is disconnected from the machine before tools
are serviced or an attachment is to be fitted or removed.
4. Never leave the machine with the power on.
5. Do not use dull, gummy or cracked cutting tools.
6. Be sure that the keys and adjusting wrenches have been removed
and all the nuts and bolts are secured.
Limited Warranty
New machines and accessories sold by Laguna Tools carry a one-year warranty
effective from the date of shipping. Machines sold through dealers must be registered
with Laguna Tools within 30 days of purchase to be covered by this warranty. Laguna
Tools guarantees all new machines and accessories sold to be free of manufacturers’
defective workmanship, parts and materials. We will repair or replace, without charge,
any parts determined by Laguna Tools, Inc. to be a manufacturer’s defect. We require
that the defective item/part be returned to Laguna Tools with the complaint. Any
machines returned to Laguna Tools must be returned with packaging in the same
manner in which it was received. If a part or blade is being returned it must have
adequate packaging to ensure no damage is received during shipping. In the event the
item/part is determined to be damaged due to lack of maintenance, cleaning or
misuse/abuse, the customer will be responsible for the cost to replace the item/part,
plus all related shipping charges. This limited warranty does not apply to natural
disasters, acts of terrorism, normal wear and tear, product failure due to lack of
maintenance or cleaning, damage caused by accident, neglect, lack of or inadequate
dust collection, misuse/abuse or damage caused where repair or alterations have been
made or attempted by others.
Laguna Tools, Inc. is not responsible for additional tools or modifications sold or
performed (other than from/by Laguna Tools, Inc.) on any Laguna Tools, Inc.
machine. Warranty maybe voided upon the addition of such described tools and/or
modifications, determined on a case-by-case basis.
Software purchased through Laguna Tools Inc. is not covered under this warranty
and all technical support must be managed through the software provider. Software is
non-refundable.
Normal user alignment, adjustment, tuning and machine settings are not covered by
this warranty. It is the responsibility of the user to understand basic machinery
operation, settings and procedures and to properly maintain the equipment in
accordance with the standards provided by the manufacturer.
Parts, under warranty, are shipped at Laguna Tools, Inc.’s cost either by common
carrier, FEDEX ground service or a similar method. Technical support to install
replacement parts is primarily provided by phone, fax, e-mail or Laguna Tools
Customer Support Website. The labor required to install replacement parts is the
responsibility of the user.
Laguna Tools is not responsible for damage or loss caused by a freight company or
other circumstances not in our control. All claims for loss or damaged goods must be
notified to Laguna Tools within twenty-four hours of delivery. Please contact our
Customer Service Department for more information.
Only new machines sold to the original owner are covered by this warranty.
For warranty repair information, call 1-800-332-4094.
6
Specification sheet.
Drift Master
Specification
Fence height
4 inches in high position
1/2 inch in low position
Fence length
31 1/2 inches
Lateral fence travel
17 inches
Fence travel per rotation
0.07 inches [1.7 mm]
Fence travel per graduation
0.004 inches [0.1 mm]
Total weight
40 lbs
Receiving your drift master.
Note. It is probable that your drift master will be delivered by a third party.
Before you unpack your drift master, you need to first inspect the packing,
invoice and shipping documents supplied by the driver.
Ensure that there is no visible damage to the packing or the drift master. You
need to do this prior to the driver leaving. All damage must be noted on the
delivery documents and signed by you and the delivery driver. You must then
contact the seller (Laguna Tools) within 24 hours.
Introduction to the drift master.
This drift master is designed to give you years of safe service. Read this
owner’s manual in its entirety before assembly or use.
7
Parts of the drift master.
4
9
12
13
10
8
7
6
5
4
3
2
1
11
8
1. Fence.
2. Lateral adjusting handle.
3. Fence support shaft.
4. Drift adjusting disc.
5. Drift release handle.
6. Drift pivot handle.
7. Fence support table.
8. Universal bracket.
9. Fence lateral clamp knob.
10. Nut special.
11. Fence clamp handles.
12. Lead screw.
13. Lead screw engage/disengage lever.
Fence.
The fence is a heavy-duty aluminum extrusion that can be fitted to either the
high or low position. The fence is adjustable to suit the width of the cut that is
required and the band saw that the drift master is being used on. The fence
attaches to the fence support table via a bar that fits into a “T” slot.
Lateral adjusting handle.
The lateral adjusting handle rotates the lead screw and moves the fence toward
or away from the blade. The handle is supplied fitted to the left hand side, but it
can be moved to the right hand side if you find it more convenient.
Fence support shaft.
The fence support shaft is a large-diameter hard-chromed steel shaft. The fence
support table rides on this shaft and guides the fence.
Drift adjusting disc.
The drift adjusting disc adjusts the angle of the fence to accommodate for drift
of the blade. Adjustments can only be made once the two clamp handles have
been released.
Drift release clamp.
The drift release clamp clamps the fence in the required angle.
9
Drift pivot clamp.
The drift pivot clamp clamps the fence to a pivot. The fence pivots about the
shaft while the drift is adjusted.
Fence support table.
The fence support table is constructed from cast iron and supports the fence and
other components of the system.
Universal bracket.
Two universal brackets are supplied to attach the drift master to the side of the
band saw.
Support table clamp.
The support table clamp clamps the fence support table to the fence support
shaft. This keeps the fence locked in the required position while cutting your
job.
Nut special.
Two nut specials are provided that fit the clamping bolts. The nut specials fit on
the inside of the table.
Fence clamp handles.
The fence clamp handles pull the fence up against the fence support bar.
Lead screw.
The lead screw, when rotated, moves the fence along the fence support shaft.
Lead screw engage/disengage lever.
The lead screw engage/disengage lever allows the lead screw to be disengaged
from the fence support table. This action reverts the drift master to a convention
fence and can be moved to any position along the fence support shaft. It is also
a convenient function, as the fence can be roughly positioned, then the thread is
engaged for fine adjustment.
Unpacking your drift master.
1. Dismantle the box.
2. Using the knife, cut the plastic wrap.
3. Remove all the parts that have been packed with the drift master.
10
Note. If you have any doubt about the described procedure, seek professional
assistance. Do not attempt any procedure that you feel is unsafe or that you do
not have the physical capability of achieving.
Packed Drift master
Cleaning the drift master.
Remove the rust protection grease with WD 40 or a similar solvent. It is
important that you remove all the grease and re-lubricate with a Teflon- based
lubricant, as Teflon has less tendency to attract sawdust and cause clogging.
You should also wax the fence, as this also protects and reduces friction.
What you will receive with the drift master.
Fence
Fixings
Nut special
Universal
brackets
11
Mounting studs
Main assembly
Assembly and setup.
The drift master can fit on most band saws, either using the existing holes on
the side of the band saw table or by drilling two holes.
The first part of this manual covers fitting the drift master using existing holes.
Note. If the universal mounting brackets hang below the bottom of the
table on your installation, they may interfere with the door. To open the
door, the table will have to be tilted.
Existing fence
Remove the existing fence.
Table of contents
