L.B. White I17 Instruction manual

Gas Conversion Kit

Individual / Zone Controlled

Radiant Brooders

View these instructions online at www.lbwhite.com

Tools required:

Phillips- head screwdriver

Adjustable wrench

Hand held butane torch

ASSEMBLY and INSTALLATION INSTRUCTIONS

Qualifications for installation:

• You must be able to read and understand these instructions.

• You must have sufﬁcient training and experience to install the kit.

• You must be able to test the brooder for proper operation.

Discussion:

These instructions are speciﬁc to radiant brooders models I-17 with D design sequence level in the model number (example:

I17P11000D). Refer to the brooder’s clearance and data plate disk.

Initial Preparation:

1. Ensure 5 PSIG is supplied to all brooders.Appropriate regulators must be installed if necessary.

2. Close the fuel supply valve and allow all heaters to cool.

3. Remove the brooder’s ﬁlter.

4. Disconnect the brooder’s gas hose.

5. Clean the brooder and its ﬁlter. Refer to the brooder’s owner’s manual for instructions.

Conversion:

1. Disassemble the brooder as shown in Fig. 1 (Individual controlled brooder) or Fig. 2 (Zone controlled brooder)

FIG. 1 (Individual Controlled)

MODULATING

VALVE BODY

LOOSEN

NUT

DISCONNECT

THERMOCOUPLE

SOFT FLAME

BYPASS

ORIFICE CLEARANCE

AND DATA

PLATE DISK

REMOVE SCREW

AND RETAINER

CLIP

AIR HOUSING

Gas Conversion Kit

www.lbwhite.com

Gas Conversion Kit •Individual and Zone Controlled Radiant Brooders

FIG. 2 (Zone Controlled)

2. Back the jam nut half - way down the threads of the original air housing assembly.

3. Using the torch, apply a soft ﬂame to the safety valve where it threads onto the air housing, sufﬁciently to

soften the thread locking compound used in assembly of the brooder.

4. Replace the air housing with the similar component form the kit.

-- Individual control heaters: replace the by-pass oriﬁce located in the modulating valve body.

5.Assemble the replacement air housing onto the brooder. See Fig. 3 and refer to the following:

a. Back the kit’s jam nut half-way down the replacement air housing’s threads.

b.Apply a couple drops of Loctite thread sealant from the kit to the air housing’s threads.

c. Thread the safety control valve onto the air housing threads at least four full turns, and as needed to

allow the safety control to be installed in an upright position.

d. Thread the jam nut hand tight against the body of the safety control valve and secure in place

with a wrench.

FIG. 3

REMOVE

JAM NUT CLEARANCE AND

DATA PLATE DISK

REMOVE SCREW

AND RETAINER

CLIP

AIR HOUSING

DISCONNECT

THERMOCOUPLE

APPLY SOFT

FLAME

APPLY LOCTITE TO FIRST

FOUR THREADS THERMOCOUPLE

AUTO RESET

ENSURE O-RINGS IS

SEATED IN JAM NUT

Gas Conversion Kit

Gas Conversion Kit •Individual and Zone Controlled Radiant Brooders

Conversion:

1. Reconnect the gas hose to the brooder, tightening it securely.

2. Ensure proper hanging conﬁguration. See the back of this instruction sheet.

3. Open the fuel supply valve and leak check using approved leak detectors.

4. Light the brooders and check for proper operation.

5. Set the second stage regulator to ensure proper gas supply pressure to all heaters in the zone. Check pres-

sure at maximum and minimum heat output. Refer to Clearance and Data Plate disk on brooder or to zone

panel.

6. When steps 1 – 5 are complete, set the temperature control on the zone panel or on individual control brood-

ers to desired setting.

7. Keep these instructions for future use.

ATTENTION:

• Ensure the brooder is hung so its control is positioned 10 to 50 down from horizontal after the gas supply hose

is attached. This allows proper venting of the brooder and prevents potential heat damage to the ﬁlter.

• Repositioning of the hanging brackets key ring may be required to achieve proper hanging position.

Installation Layout for Safe Clearances:

INSTALLATION LAYOUT

FOR SAFE CLEARANCES

I17 - 3 FT. MINIMUM

BROODER TOP TO CEILING

POSITION THE GAS HOSE AND ELECTRICAL POWER CORD

OUTSIDE OF THE HOT ZONE DIRECTLY ABOVE THE HEATER.

POSITION THE GAS HOSE AND POWER CORD TO AVOID

ANY OPPORTUNITY FOR CONTACT WITH THE HOT CANOPY

SURFACE OF THE HEATER.

MINIMUM 3 FT. CLEARANCE

TO COMBUSTIBLES

FLOOR

I17 - 3.5 FT. MINIMUM

POINT OF COMBUSTION

CONE TO FLOOR

HANG THE HEATER WITH THE

CONTROL END 1 TO 5 DEGREES DOWN

FROM HORIZONTAL (SEE BELOW)

CONTROL PANEL

GAS PIPING

THIS NOT THIS

CONTROL END

KEYRING

STEEL CABLE

HANGING

CONTROL END

OR CHAIN

BRACKET

OF HEATER

MUST BE 1 TO 5 DOWN

FROM HORIZONTAL

Contact your local L.B. White dealer for replacement parts

and service. You may also call the L.B. White Co., Inc. at

U.S. & Canada: 1-800-345-7200, Overseas: 001-608-783-5691

assistance, or email us at [email protected].

Be sure that you have your heater model number and

conﬁguration number when calling.

Service

WORLD PROVIDER - INNOVATIVE

HEATING SOLUTIONS

411 Mason Street, Onalaska, WI 54650

800-345-7200 • 608-783-5691

608-783-6115 (fax)

www.lbwhite.com

150-28263 REV.B

Other manuals for I17

Other L.B. White Heater manuals

L.B. White

L.B. White Therma Grow 120NG Manual

L.B. White

L.B. White CP300CKI Manual

L.B. White

L.B. White TS350DF Manual

L.B. White

L.B. White CP045DK Manual

L.B. White

L.B. White CV100 Manual

L.B. White

L.B. White Tradesman K70 User manual

L.B. White

L.B. White CR125AZPA220206 Manual

L.B. White

L.B. White PALS Manual

L.B. White

L.B. White Tradesman CP045CK Manual

L.B. White

L.B. White Therma Grow 120 User manual

L.B. White

L.B. White GUARDIAN Smart Sense AD250 Instruction manual

L.B. White

L.B. White Foreman CI230 Manual

L.B. White

L.B. White Sun Blast CR015 Instructions for use

L.B. White

L.B. White Journeyman User manual

L.B. White

L.B. White Director CP100AKI Manual

L.B. White

L.B. White Tradesman K70 User manual

L.B. White

L.B. White 377 Operating instructions

L.B. White

L.B. White Premier TS080 Manual

L.B. White

L.B. White AW230 Manual

L.B. White

L.B. White Twin Jet 400 Manual

L.B. White

L.B. White Sun Blast HD CR100 Manual

L.B. White

L.B. White Tradesman 400 Dual Fuel Manual

L.B. White

L.B. White CP350AK User manual

L.B. White

L.B. White AD060 Manual

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide