KYMCO Stryker 125 User manual

Dear KYMCO Motorcycle Users:

Before the delivery of each new motorcycle, the fuel in carburetor is

drained off to ensure the excellent performance and safety of the

motorcycle. Therefore, when first starting a new motorcycle, it is

normal to take 20～30 seconds. The quality of each KYMCO

motorcycle is guaranteed.

Dear Users:

We greatly appreciate your patronage of KYMCO STRYKER 125/150

This User‘s Manual describes the correct operating methods, inspection and

maintenance procedures for the KYMCO STRYKER 125/150 details in order

to prolong the service life of motorcycle and provide you with a comfortable

riding.

Please note that the information and illustrations included in this manual may be

different from the motorcycle in case specifications are changed.

To enable you to have a safe and comfortable riding, we recommend you to read

this manual carefully and wish you a happy riding.

Note: 1. The information and specifications stated in this manual are for reference only

and subject to change without notice.

2. When starting the engine, the battery must be installed to facilitate starting

and increase the engine performance.

TABLE OF CONTENTS

1. PRECAUTIONS FORA SAFE RIDING................................................................. 1

2. ASSEMBLY PARTS................................................................................................... 3

3. OPERATION INSTRUCTIONS............................................................................... 5

4. PRE-RIDE INSPECTION....................................................................................... 10

5. ENGINE STARTING METHODS ......................................................................... 19

6. NORMAL RIDING METHOD............................................................................... 22

7. PRECAUTIONS FOR RIDING ............................................................................. 24

8. HOW TO STOP RIDING........................................................................................ 27

9. EASY MAINTENANCE.......................................................................................... 29

10. IMPORTANT NOTICES ........................................................................................ 36

-1-

1. PRECAUTIONS FOR A SAFE RIDING

(1) CLOTHES

yTo relax and wear comfortable clothes are the

main points for a safe riding.

yTo observe traffic laws, keep a cool mind, relax

and be careful will provide you a safe riding.

cWear helmet and fasten it tightly.

dHave the clothes well-arranged. Fasten shirt

cuffs and keep them from hooking the brake

lever.

eWear low-heeled shoes for a safe riding.

fWhen riding, use both hands to grasp the

handlebar. It is very dangerous to hold the

handlebar with one hand.

nCAUTION:

yA motorcycle rider should not wear loose or too

long clothes to avoid danger.

yDuring riding or 10 minutes after the motorcycle

is stopped, do not touch the exhaust muffler to

avoid scalding.

yWhen parking the motorcycle, keep it away from

dry lawn or inflammables to avoid danger.

-2-

(2) RIDING METHOD

yThe safety of two-wheel vehicles is influenced by

sitting position. The rider should sit on the central

part of the seat cushion. If the rider sits on the

rear part of the seat, the load of front wheel will

decrease. As a result, the handlebar will swing

and cause danger to the rider.

yWhen making a turn, it will be easier for the rider

to steer the motorcycle by leaning the body

inward slightly. The motorcycle will lose its

balance if the rider fails to keep his body leaning

inward.

yWhen riding on a damaged or macadam road.

Slow down the speed and hold the handlebar

tightly.

(3) CARRYING GOODS

yKeep a good sitting posture to operate the

motorcycle properly.

yThe feel of the handlebar will be different when

carrying goods on the motorcycle. Overloading

may cause the handlebar to swing. Avoid riding

with overload.

cMax. loading capacity of the rear carrier is 3kg.

-3-

2. ASSEMBLY PARTS

Engine Serial No.

Clutch panel

Taillight

Stoplight

Side Suppor

L. Front Turn

Signal Light

Turn Signal Switch

Headlight Dimmer Switch Fuel Tank

Cap

VIN (Vehicle

Identification No.) L. Rear Turn

Signal Light

Tool Boxp

-4-

Starte

Button

Kick Leve

Rear Brake Leve

Ignition

Switch

Exhaust Pipe

Instruments

Frame Serial No.

R. Front Turn

Signal Light

R. Rear Turn

Signal Light

-5-

3. OPERATION INSTRUCTIONS

(1) IGNITION SWITCH/STEERING

HANDLEBAR LOCK

cON :At this position, power is connected to

start the engine. The key cannot be

taken out.

dOFF :At this position, power is cut off and the

engine stops. The key can be taken out.

eLOCK :At this position, the steering handlebar

is locked. The key can be taken out

《Locking Method》

Turn the steering handlebar left to the full and then

press to turn the ignition switch key to “LOCK”

position and the handlebar is locked.

《Unlocking Method》

Turn the key to “OFF” and the lock is released

automatically.

nCAUTION:

yAfter locking, turn the handlebar gently to make

sure that it is locked.

yDo not turn the ignition switch to “LOCK”

during riding, or the handlebar will be out of

control and cause accidents.

yDon‘t park your motorcycle at a place to hinder

the traffic.

-6-

(2) STARTER BUTTON

yRelease the steering handlebar lock before

starting the engine. Turn on the ignition switch

and then press the starter button. Make sure to

depress the gear shift pedal into the neutral

position to avoid engine damage.

nCAUTION:

yDuring engine running, do not push the starter

button to avoid engine damage.

yBefore starting the engine, please rebound the

side stand.

(3) HEADLIGHT SWITCH/ HORN BUTTON

zAt this position, the position light,

headlight, instrument lights and taillight go

out together.

P At this position, the position light, instrument

lights and taillight light together.

HAt this position, the position light, headlight,

instrument lights and taillight light together.

yWhen the ignition switch is turned “ON”, press

the horn button and the horn will sound.

yThe horn switch do not work when the ignition

switch is “OFF”.

-7-

(4) HEADLIGHT DIMMER SWITCH/

PASSING SIGNAL SWITCH

HI Switch to this position for using high beam.

LO When riding in downtown area or there is a

car coming from the opposite direction, use

low beam to avoid affecting the visibility of

coming cars.

PASSING When passing, if there are cars coming

from the opposite direction, press and

release the PASSING switch and the

headlight will wink to warn the

coming cars.

(5) TURN SIGNAL SWITCH

yThe turn signal switch do not work when the

ignition switch is “OFF”.

yWhen the winker lamp is used, both the winker

lamp on the panel will blink same time.

cÖFor turning to the right. dÕFor turning to

the left. ePush the turn signal switch button to

release it.

nCAUTION:

yThe turn signal light will not release

automatically. Be sure to reset it after use;

otherwise it may affect the traffic safety.

PASSING

This manual suits for next models

Table of contents

Other KYMCO Motorcycle manuals

Popular Motorcycle manuals by other brands

OHVALE

OHVALE GP-0 Use & maintenance

Yamaha

Yamaha Star XV19CTSZ 2009 owner's manual

KTM

KTM 350 XCF-W USA owner's manual

HYOSUNG

HYOSUNG ST7 owner's manual

Husqvarna

Husqvarna FC 250 2016 owner's manual

Ducati

Ducati SCRAMBLER 800 Workshop manual

MOTO GUZZI

MOTO GUZZI QUOTA 1100 ES owner's manual

APRILIA

APRILIA ETV MILLE CAPONORD - PART1 02-2001 manual

Yamaha

Yamaha 2006 YZF-R1V owner's manual

KTM

KTM Freeride E-XC 2021 owner's manual

Fantic

Fantic Enduro 125 user manual

Ducati

Ducati Supersport 750 desmodue owner's manual

MV Agusta

MV Agusta 2008 F4 312RR 1078 Workshop manual

Yamaha

Yamaha XVS650A owner's manual

Yamaha

Yamaha YZF-R6T(C) Supplementary service manual

Ducati

Ducati 748 monoposto strada owner's manual

ATK

ATK 1988 250 owner's manual

Excelsior-HENDERSON

Excelsior-HENDERSON 1999 HCX Riders handbook