Krups KP1010 User manual

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should

always be followed to reduce the risk of fire, electric shock, and/or

injury to persons including the following :

1. Read the instructions carefully before using your appliance for

the first time: use that does not comply with the instructions

will release Krups from any responsibility.

2. Do not touch hot surfaces. Use handles or knobs.

3. To protect against fire, electric shock and injury to persons, do

not place cord, plugs or appliance in water or other liquid.

4. Not intended for use by children. Close supervision is necessary

when any appliance is used near children.

5. Unplug from outlet when not in use and before cleaning. Allow

to cool before putting on or taking off parts, before cleaning

the appliance, and before storing.

6. Do not operate any appliance with a damaged cord or plug or

after the appliance malfunctions, or has been damaged in any

manner. Return appliance to the nearest KRUPS Service Center

for examination, repair or adjustment.

7. The use of accessory attachments not recommended by KRUPS

may result in fire, electric shock or injury to persons.

8. Do not use outdoors.

9. Do not let cord hang over edge of table or counter, or touch hot

surfaces.

10. Do not place on or near a hot gas or electric burner, or in a

heated oven.

11. Before unplugging the appliance, check that it is not switched

on (light off).

12. Do not use the appliance for other than intended use.

13. Do not pour liquids other than water and descaling solutions

specified in this manual into the water tank.

14. Do not operate the coffee maker without water.

15. Make sure that the upper lid is properly locked before starting

the brew process.

English

sauvegarde 3 US.PM6.5 4/05/06, 11:094

16. Do not unlock the upper lid while coffee is being prepared.

17. This appliance is for household use only. Any servicing, apart

from cleaning and maintenance mentioned in the manual,

should be carried out by a Krups approved service center.

SAVE THESE INSTRUCTIONS

SHORT CORD INSTRUCTIONS

A. The length of the cord has been chosen to reduce the risk of

accidents.

B. Extensions are available and may be used with care.

C. If you use an extension,

1) its electric capacity must be equal to or greater than that of

the appliance,

2) The extension and the cord should be arranged so that they

do not hang over the work top or table, in order to prevent

children being able to pull on them or someone accidentally

tripping and falling.

D. This appliance has a polarized plug (one blade is wider than

other). To reduce risks of electric shock, this plug is intended to

fit into a polarized outlet only one way. If the plug does not fit

fully into the outlet, reverse the plug. If it still does not fit,

contact a qualified electrician. Do not attempt to modify the

plug in any way.

sauvegarde 3 US.PM6.5 4/05/06, 11:095

ADrip tray

BDrip tray plate

CSpray head

DLock lever

EUpper lid

FTank

GTank lid

HCoffee pod holder (one left-side and one right-side)

ISpecialty pod holders (one left-side and one right-side)

JWater filter holder

KWater filtration change indicator

LWater filter (Duo filter)

MOn/Off button

NIndicator light

OBrew button

PBrew selection control

QRemovable nozzle (depending on model)

DESCRIPTION

sauvegarde 3 US.PM6.5 4/05/06, 11:096

BEFORE FIRST USE

Read all instructions carefully.

• Remove all packaging and stickers from the product.

• Rinse all components completely.

• Fill the tank (F) with cold drinking water up to the “max” mark.

• Unlock the upper lid (E) by moving the lever (D) to the far left

position.

• Lift the upper lid.

• Position 2 coffee pod holders without the pods.

• Close and lock the upper lid (E) by moving lever to the right.

• Place a container on the drip tray beneath both spouts.

• Turn the Brew Selection Control (P) to the setting for two 9-oz cups.

• Press the on/off button (M).

The brew indicator light blinks slowly while preheating and then glows consistently when the

coffee machine is ready to brew.

• Press the brew button (O).

sauvegarde 3 US.PM6.5 4/05/06, 11:097

The brew indicator light blinks once and brewing starts, the container will be filled with hot

water rinsing the system. Discard the hot water. Your Home Cafe is now ready for use.

Your appliance may include an optional nozzle attachment (Q).

This nozzle attachment can be used to regulate the flow of the beverage into the cup.

It is recommended to remove and rinse the attachment after each use.

Your coffee machine is equipped with water filtration

The Duo-Filter is a double action anti-chlorine and anti-scaling filter (Krups steampart # 472-00).

The filter’s anti-chlorine action allows the most subtle flavors of the coffee to be released. The

level of chlorine in tap water very often prevents the flavor of the coffee from fully developing.

The anti-scaling action means that descaling is needed less frequently. (see descaling on page

12)

The components of the “Duo Filter” (plant-based active charcoal and anti-scaling resin) comply

with food safety standarts. The filter can be disposed of with household waste.

• Remove the “Duo Filter” (L) from its plastic bag and

soak it in tap water for 1 minute.

• Open the lid of the water tank and remove the water

filter holder (J).

• Release the lower part of the filter holder and insert

the filter in its housing.

• Replace the filter support in the coffee maker.

Note: An indicator with numbers 1-12 to correspond to months of the year is located on the

upper part of the filter support to remind you when to change the “Duo Filter” (K):

For example: If you insert the “Duo Filter” at the beginning of January, you should change it at

the beginning of May (set to 5) depending on the hardness of the water in your area.

The absence of the water filter does not prevent the coffee machine from working.

If you have not used your coffee machine for over a month, we advise you to rinse the “Duo

Filter” under running water and to thoroughly clean the water tank.

It is recommended not to leave the water filter in place for over 5 months.

sauvegarde 3 US.PM6.5 4/05/06, 11:098

PREPARING COFFEE

Do not use ground coffee or torn pods, as you risk damaging your coffee machine.

• Fill the tank with fresh cold drinking water to the desired

level. The quality of the water is a prime factor in the taste of

your coffee.

Do not fill the tank with anything other than water.

• Press the on/off button (M) to start your appliance.

The indicator light blinks while the appliance is warming up.

• Unlock the upper lid (E) by moving the lock lever (D) to the far left position.

• Lift the lid.

Choose the type of pod holder to insert:

(H) (I)

Use of coffee pod holder

• Insert pod holders (H) or (I).

- Use smaller pod holders (H) for regular coffee.

- Use the larger specialty pod holder (I) for cappuccino or latte and tea.

Do not use regular coffee or tea pods in the specialty pod holders.

• Position the pod(s) in the pod holders with the flat surface facing

upwards.

The specialty coffee pods are easily identified by their size, over 1’’ thick.

sauvegarde 3 US.PM6.5 4/05/06, 11:099

If you are preparing one cup, use the left pod holder marked «ONE CUP THIS SIDE»

• Close and lock the upper lid (E) by moving the locking

lever (D) to the far right.

• Turn the brew selection control to the desired setting.

Note : «the setting marked late are programmed

specifically for specialty pods».

For regular coffee or tea pods use any of the other one

cup ( ) or two cups ( ) settings.

• Place the mug(s) on the drip tray.

When the indicator light glows steadily, your appliance is ready to brew.

• Press the brew button (O) to start the preparation. The indicator light

will blink during the brewing process.

At the end of the brew cycle there is a steam purge. You may see some steam

dissipate from the unit. This process completes the extraction of flavor from the

coffee pod, at the same time clearing the system and drying the pod for easier

disposal.

If brewing stops mid-cycle check to see that there is water in the tank.

• Remove and discard the pod(s) using the pod holders when complete.

• After preparing a specialty beverage such as a latte or cappuccino, immediately clean the spray

heads and the seals using a damp cloth, then thoroughly wash the pod holders. In addition,

you can run a cycle without pods to rinse the appliance.

Never open the upper lid when the indicator light is blinking (brewing in progress).

sauvegarde 3 US.PM6.5 4/05/06, 11:0910

The coffee machine will automatically shut off after 1 hour if not used.

You can interrupt the brewing cycle by pushing the brew button. The brewing will stop and go

directly to the steam phase (purge). The brew indicator light will steady at the end of this phase.

If, during the brewing, you stop your machine by pressing the on /off button (M), your coffee

machine will stop. You will not have a steam (purge). Wait two minutes before opening the brew

head.

Immediately clean the spray heads and the seals using a damp cloth, then thoroughly wash

the pod holders.

If you change the volume during brewing by turning the selector (P) the new volume will be

used.

Particular attention for the use of the « specialty » pod holders (I)

Before use :

The « specialty » pod holders are equipped with a removable nozzle.

The removable nozzle provides a creamy foam finish on top of the cappuccino or latte drinks.

Before use, check that they are not clogged.

It is important to keep these nozzles clean and free of any sediment to prevent clogging.

Rinse with warm water after each use. Periodically or if clogged, remove the nozzle more

thoroughly clean.

To remove the nozzles :

• Push the tip of the nozzle from the bottom.

• Pull the nozzle out from inside the pod holder.

• If the small holes are blocked, unblock them by using a fine needle.

• Run under hot water.

• Ensure that the 2 gaskets are in place.

• Reinsert the nozzle into the pod holder from the top.

• The nozzle is correctly in place when the end of the nozzle is visable

from the end of the exit tube on the pod holder.

sauvegarde 3 US.PM6.5 4/05/06, 11:0911

CLEANING

• Run a brewing cycle without pod(s) to rinse the appliance.

• Unplug the appliance.

• Do not clean the appliance when hot.

• Clean with a damp cloth or sponge.

• Never put the appliance in water or under running water.

•Occasionally clean the spray head and the gaskets with a wet cloth.

• The pod holders (H), the drip tray (A) and its plate (B) are dishwasher safe.

•It is recommended to remove and rinse the nozzle (Q) after each use.

DESCALING

• Turn the appliance off before descaling.

• Remove the water filter holder and discard the water filter (Duo Filter).

• We recommend that you use KRUPS descaling solution (ref: 42821). Mix descaling solution as

directed.

• Pour the mixture into the tank (F) and place the smaller pod holders in the coffee machine.

(Do not use the specialty pod holders for descaling.)

• Place a container that can hold up to 40 ounces on the drip tray.

• With the unit’s power turned off, press the brew button for at least 5 seconds.

The indicator light will begin to blink slowly. The solution will run through the system and

disperse intermittently.

The descaling cycle automatically stops when the tank is empty. The indicator light goes out.

After descaling rinse your coffee machine by running two brew cycles on the 2 cup 9 oz setting.

• Rinse the water tank before making coffee.

Never put the descaling agent directly into the tank, mix the solution first into water.

Because your machine is equipped with Water Filtration you generally only need to

descale your appliance every 4 to 5 months.

Caution: Do not leave the descaling solution within the reach of children.

The warranty excludes coffee machines that are not working properly because they

have not been descaled.

sauvegarde 3 US.PM6.5 4/05/06, 11:0912

ACCESSORIES

In the United States, accessories can be purchased at most Krups retailers or by calling 1-888-

344-0727.

• Duo Filter Water Filtration Cartridges - pack of 2 : Reference # F472

• Descaling Solution : Reference # 42821

TROUBLESHOOTING

PROBLEM SOLUTION

The brew cycle stops and the indicator • The water tank is empty and the

light blinks rapidly during brewing : brew cycle has been interrupted. Fill the

water tank. Press “brew”to begin

a new cycle. When you reach

the volume required, press “brew” again

to end the preparation.

• The circuit is blocked: wait until your

coffee maker has cooled down

completely, then open the upper lid (E).

- Check that the pod holders are not

blocked. If this is the case, the pod

holders should be cleaned.

- Otherwise, descale the unit.

A large amount of steam is given off • Descale the unit.

during the brewing :

The tank is not emptied during the • Your coffee maker is heavily scaled,

descaling cycle : repeat the descaling cycle.

You cannot unlock the lid : • Do not force the unlock button, wait

until your coffee machine has cooled

down completely and then try again. It is

sometimes necessary to wait 24 hours

before unlocking the lid. This generally

occurs when the spout has some restric-

tion or is clogged. After allowing time for

the pressure to clear unlock the lid and

clear the restriction before brewing

again.

Drinks prepared are not hot : • Descale the unit.

Power cut during the preparation : • Wait until your coffee machine has

cooled down completely.

• Throw away the pods, clean the pod

supports and the spray heads and run 1

2*9-oz preparation cycle with empty

coffee pod supports to rinse your

appliance.

Clog : • If the nozzle of the pod holder is

clogged clean it with a fine needle.

sauvegarde 3 US.PM6.5 4/05/06, 11:0913

Table of contents

Other Krups Coffee Maker manuals

Krups

Krups CafePresso 171 User manual

Krups

Krups EA8911 User manual

Krups

Krups Nespresso my machine CITIZ MILK YY2730 User manual

Krups

Krups Espresso Automatic EA88 Series User manual

Krups

Krups XP52 Series User manual

Krups

Krups AUTOMATIC XP52 Series User manual

Krups

Krups Evidence ECO-Design User manual

Krups

Krups XP228050 User manual

Krups

Krups Nespresso Prodigio&Milk XN411T10 User manual

Krups

Krups Nespresso Maestria XN800 User manual

Krups

Krups EA81P070R User manual

Krups

Krups CONTROL KM442D50 User manual

Krups

Krups ESSENZA XN2003 User manual

Krups

Krups XP6180 User manual

Krups

Krups EA815050 User manual

Krups

Krups KM600 User manual

Krups

Krups NESPRESSO CITIZ XN740 User manual

Krups

Krups EA875 INTUITION PREFERENCE User manual

Krups

Krups Intuition Preference EA872 User manual

Krups

Krups NAPOLI ROMA User manual

Krups

Krups Excellence KM480 User manual

Krups

Krups KM101050 User manual

Krups

Krups Nescafe Dolce Gusto PICCOLO XS User manual

Krups

Krups T8 User manual

Popular Coffee Maker manuals by other brands

Taurus

Taurus Livorno 6 manual

Delta-q

Delta-q QUICK instruction manual

Bunn

Bunn LCA-1 Installation & operating guide

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Use and care book

Saeco

Saeco Vienna Plus Sup 018M operating instructions

DeLonghi

DeLonghi DC300 Owner's instructions

INCAPTO

INCAPTO BXCO1470E Instructions for use

Bosch

Bosch TASSIMO finesse TAS16B Series user manual

Exido

Exido 245-072 Specifications

Animo

Animo OptiVend Choco user manual

Siemens

Siemens TQ505DF Series user manual

DeLonghi

DeLonghi ECI341 Instructions for use

Cimbali

Cimbali M32 Classic manual

Philips

Philips HL3844N Service manual

Bosch

Bosch TES 515 SERIES instruction manual

Tekmatix

Tekmatix TMFM - 65 Operation manual

Scarlett

Scarlett SC-CM33005 instruction manual

LAVAZZA

LAVAZZA CLASSY PLUS instructions