Kramer VS-62HA User manual

KRAMER

VS-62HA Quick Start Guide

This guide helps you install and use your VS-62HA for the first time. For more detailed information, g

http://www.kramerav.com/manual/VS-62HA to download the latest manual or scan the QR code on the left.

o to

Step 1: Check what’s in the box

1 Power cord

1 Quick Start Guide

1 Set of rack “ears”

4 Rubber feet

VS-62HA 6x2 HDMI/Audio Matrix Switcher

IR remote control transmitter with batteries

Step 2: Install the VS-62HA

To mount the VS-62HA in a rack, attach both “ear” brackets to the machine using the three screws on

each side of the machine. Alternatively, attach the rubber feet to the bottom of the machine and place

it on a table.

Step 3: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your .

For best results, always use Kramer high-performance cables to connect your AV equipment to the .

VS-62HA

VS-62HA

WWW.KRAMERAV.COM

Laptop/

Desktop VIA Connect PRO Remote Input

Select Switch

Remote Input

Select Switch

Dante Audio

Source

Audio

Receiver

Audio

Receiver

Controller

LCD

TV

LCD

TV

VS-62HA Quick Start (P/N: 2900-300469QS REV 2)

2 9 0 0 - 3 0 0 4 6 9 QS

2

P/N: Rev:

Left

Right

Ground

For the Ethernet and HDBaseT connectors,

see the proper wiring diagram below

1

2

3

4

5

6

7

8

Orange / White

Orange

Green / White

Blue

Blue / White

Green

Brown / White

Brown

PIN Wire Color

EIA / TIA 568B

RJ-45 Pinout Audio Input

Pinout

For optimum range and performance use

Kramer's

BC-HDKat6a cable. This specially built cable significantly

outperform regular CAT 5/CAT 6 cables.

Balanced

stereo audio output

Balanced

stereo audio output

to unbalanced

acceptor

Line Output Pinout

Step 5: Operate via the front panel buttons and via the:

WWW.KRAMERAV.COM

IR Remote Embedded Web Page

Step 4: Connect the power

Connect AC power to the rear of the switch on its power and then switch on

the power on each device.

VS-62HA,

RS-232 and Ethernet

RS-232

Protocol 3000 (Default) Legacy

Baud Rate: 115,200 9,600

Data Bits: 8 8

Stop Bits: 1 1

Parity: None None

Command Format: ASCII ASCII

Example (Set display mode to Picture in Picture): #Y 0,110,1<CR> >Y 0 110 1<CR>

Ethernet

To reset the IP settings to the factory reset values, power cycle the device while holding in the Ethernet Reset button, located on the

rear panel of the unit

IP Address: 192.168.1.39

Subnet mask: 255.255.000.000

Default gateway: 000.000.000.000

TCP Port #: 5000

UDP Port #: 50000

Maximum UDP Ports: 10

Maximum TCP Ports: 4

Web page password 1234

Full Factory Reset

Front panel buttons Turn power off. Turn power on again while holding the RESET TO XGA/720p front panel button.

The LEDs blink. Full factory reset is complete once the LEDs cease to blink and react normally.

Note that Full Factory reset includes Ethernet reset as well

OSD Factory Reset through the Misc menu item

Web pages Factory reset via the Device Settings embedded Web page

Protocol 3000 Use “Factory” command or #Y 0,771,1<CR>

Other manuals for VS-62HA

2

Other Kramer Matrix Switcher manuals

Popular Matrix Switcher manuals by other brands

Broadcast Tools

Broadcast Tools SS 8.2 Installation and operation manual

Altimium

Altimium MATF32 user manual

ALFAtron

ALFAtron ALF-MUK44N manual

Monoprice

Monoprice Blackbird 15377 user manual

PTN

PTN FMX12 user manual

CYP

CYP nT15GX01 Operation manual

TESmart

TESmart HMA0402A40 quick start guide

Octava

Octava HD4XSTPMX installation guide

Intelix

Intelix FLX-88 Installation and operation guide

Roland

Roland XS-1HD owner's manual

Atlona

Atlona AT-HDMI-22M user manual

Link

Link HD8X8 user manual

AMX

AMX AVS-OP-2020-117 Product View

Lindy

Lindy 38042 quick start guide

Extron electronics

Extron electronics MTPX Plus Series Setup guide

Key Digital

Key Digital Champion KD-16x16CS operating instructions

Shinybow USA

Shinybow USA SB-8811 instruction manual

Optimus

Optimus Compact operating instructions