Kostal PLENTICORE plus Instruction Manual

Seite 1 / 12 DOC_Guide_PLENTIOCRE_BYD_ 2019-04-17-FW_1.20_EN

Guideline

Commissioning PLENTICORE plus inverter in

combination with a BYD Battery-Box HV H5.1 -

H11.5

This guide does not replace the operating instructions or manuals required for proper assembly and installation.

The trademarks, trade names, product descriptions and other designations used may be protected by law even without special

designation (e.g. as trademarks). KOSTAL Solar Electric GmbH does not assume any liability or warranty for their free usability.

Great care has been taken in the compilation of illustrations and texts. Nevertheless, errors cannot be excluded. The compilation

is made without guarantee. Technical changes and errors excepted

Seite 2 / 12 DOC_Guide_PLENTIOCRE_BYD_ 2019-04-17-FW_1.20_EN

IMPORTANT INFORMATION

Installation may only be carried out by a trained and qualified electrician!

Observe the safety instructions in the operating instructions for the inverter and

the battery.

In order to start up the system completely and to make all necessary settings,

the Service/PARAKO password and a computer/tablet as well as the battery

activation code are required.

The inverter and the battery must be completely disconnected from the voltage supply for all work on the inverter

or on the supply lines. Refer to the relevant operating instructions for the respective devices (inverter/battery).

Install PLENTICORE plus inverter, connect AC cables and control cables but DO

NOT start up yet.

DO NOT yet connect the DC plug of the PV strings to the inverter.

Connect DC cable, connect ground cable, connect RS485 cable to the BCU and to

the SCB of the WR, but DO NOT yet put into operation.

DO NOT yet connect the DC plug of the battery to the inverter.

Install the Energy Meter or Energy Manager and connect the RS485 cable to the SCB

of the inverter.

Establish LAN connection between inverter and router (customer network).

Connection of the RS485 cable of the Energy Meter or Energy Manager with the SCB (X452) of

the PLENTICORE plus inverter.

Seite 3 / 12 DOC_Guide_PLENTIOCRE_BYD_ 2019-04-17-FW_1.20_EN

The Modbus RTU interface (A) is preconfigured as standard with the readout intervals

for the PLENTICORE plus or PIKO IQ inverters.

The KOSTAL Smart Energy Meter can be installed directly in the sub-distribution

cabinet and connected to the inverter without a PC (adjustment of parameters) and

other settings. The device is immediately ready for use.

ATTENTION: The B-control EM300 LR and the KOSTAL Smart Energy Meter

have different RS485 pin connections.

Seite 4 / 12 DOC_Guide_PLENTIOCRE_BYD_ 2019-04-17-FW_1.20_EN

X601 on the SCB in PLENTICORE plus inverter.

Position of jumper, it must be plugged

to JP2, newer BCU devices have two

jumpers plugged to (JP1 and JP2).

Connection of the RS485 cable of the BCU from the BYD Battery-Box HV to the SCB (X601) of

the PLENTICORE plus inverter.

Configuring the BCU of the BYD Battery-Box HV via WLAN

Activating the WLAN on the computer

Select the BYD battery from the list of devices in the WLAN network

Enter the network key for the WIFI of the BYD battery access: 123456789

In the URL field of the browser now enter the IP of the BCU: 192.168.5.1

A login window will open

Enter username: installer and password: byd@12345 and confirm

The web server opens with the "HOME" page

Click on "Installation" in the menu

The "Installation" window opens

All necessary values for the configuration are now entered here

Seite 5 / 12 DOC_Guide_PLENTIOCRE_BYD_ 2019-04-17-FW_1.20_EN

The time and date must be entered.

Then click on the "Next" button.

Series Battery Counts - Enter number of memory modules - 4 to 9

Inverter - Select inverter manufacturer - KOSTAL

Country - Select your country –e.g. Germany

Finally click on the "Finish" button.

The battery system restarts and is ready for operation.

Seite 6 / 12 DOC_Guide_PLENTIOCRE_BYD_ 2019-04-17-FW_1.20_EN

Initial commissioning of the PLENTICORE plus inverter

Attention: Commissioning only possible with sufficient PV voltage and irradiation.

Check the RS485 connection Energy Meter to the SCB of the inverter.

Plug in the DC plug of the PV strings.

Connect the DC plug of the battery.

Switch on AC fuses.

Switch on DC Switch.

The start-up process of the inverter has started.

The installation assistant appears in the inverter display.

Commissioning can be carried out completely via the display.

Simply follow the instructions on the display.

Alternatively, the commissioning can also take place partly via the web server.

oSelect language, date and country in the display.

oActivate IPv4 / DHCP in the display

oSelect e.g. the NSR Germany country code in the display and complete the

installation.

Make all other settings on the web server of the inverter.

Read IP address from inverter display.

Enter the IP of the inverter into the URL line of your browser e.g. Mozilla or Firefox.

The login window will open.

Seite 7 / 12 DOC_Guide_PLENTIOCRE_BYD_ 2019-04-17-FW_1.20_EN

All other settings can now be entered in the service menu.

Service menu Energy management: Choice of energy meter and position of the

sensor

Seite 8 / 12 DOC_Guide_PLENTIOCRE_BYD_ 2019-04-17-FW_1.20_EN

Checkbox: "Storage of excess AC energy from local generation."

This feature works with the Energy Manager from B-control, the EM300 LR

as well as with the KOSTAL Smart Energy Meter (KSEM).

IMPORTANT: The sensor (Energy Manager/Meter) must be mounted in the

"Mains connection point" position.

Activate reception of Broacast control signals

Service menu Energy management: Activate storage of excess AC energy from

local generation.

Seite 9 / 12 DOC_Guide_PLENTIOCRE_BYD_ 2019-04-17-FW_1.20_EN

Service menu Battery settings: All settings for the connected battery made here.

Seite 10 / 12 DOC_Guide_PLENTIOCRE_BYD_ 2019-04-17-FW_1.20_EN

When all settings have been completed, the KOSTAL storage system is running. The

green LED on the inverter lights up.

The PLENTICORE plus (or PIKO IQ) is now ready for operation.

A firmware update is available: Download from our homepage

Download and install the software for the PLENTICORE plus inverter that was released/up to date at

the time of installation. This software can be downloaded from our homepage under the following link:

https://www.kostal-solar-electric.com/de-

de/download/download#PLENTICORE%20plus/PLENTICORE%20plus%2010/Deutschland/Update/

Install the software package as described in detail in the inverter operating instructions.

Other manuals for PLENTICORE plus

This manual suits for next models

Other Kostal Inverter manuals

Kostal

Kostal PIKO Inverter 3.0 How to use

Kostal

Kostal PIKO 1.5 MP User manual

Kostal

Kostal PLENTICORE plus How to use

Kostal

Kostal PIKO CI How to use

Kostal

Kostal PIKO 3.0 User manual

Kostal

Kostal PLENTICORE plus User manual

Kostal

Kostal PLENTICORE plus How to use

Kostal

Kostal PIKO CI User manual

Kostal

Kostal PIKO MP plus series User manual

Kostal

Kostal PLENTICORE BI How to use

Kostal

Kostal PIKO 10 User manual

Kostal

Kostal PIKO CI User manual

Kostal

Kostal PIKO 10 User manual

Kostal

Kostal PIKO IQ How to use

Kostal

Kostal PIKO 10-20 User manual

Kostal

Kostal PLENTICORE plus G2 User manual

Kostal

Kostal PIKO MP plus 1.5-1 Manual

Kostal

Kostal PIKO User manual

Kostal

Kostal PIKO 36 EPC User manual

Kostal

Kostal PIKO 36 EPC How to use

Kostal

Kostal PLENTICORE plus G2 User manual

Kostal

Kostal PLENTICORE plus User manual

Kostal

Kostal PIKO 4.2 User manual

Kostal

Kostal PIKO 6.0 BA How to use

Popular Inverter manuals by other brands

Fourgroup

Fourgroup Easy use and Programming Handbook

Velleman

Velleman PI300M user manual

Sungrow

Sungrow SG350HX-US user manual

WilTec

WilTec 61897 Operation manual

SMA

SMA SUNNY BOY STORAGE 2.5 Quick reference guide

Simplicity

Simplicity LANDLORD 316 product manual

Santak

Santak SMAX 3000 user manual

ATON

ATON RA.Store-3 user manual

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ operating instructions

Tektronix

Tektronix CFG250 Operator's manual

Champion

Champion 200989 Operator's manual

Vanner

Vanner 20-500 Series owner's manual

GE GEP user manual

Astrel Group

Astrel Group Power Reducer Installation and instruction manual

MULTIQUIP

MULTIQUIP GDP-5H Operation and parts manual

GoWISE

GoWISE PS1007 user manual

Promate

Promate PM13500D ES Operator's manual

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM user manual