Korenix JetNet 6059G User manual
JetNet 6059G Series
Industrial 9-port Gigabit Managed
Ethernet Switch
Quick Installation Guide
www.korenix.com
V1.0
Introduction
JetNet 6059G series is an Industrial Gigabit Managed Ethernet Switch with 9 full gigabit
ports and 32G switching backplane to ensure high quality data transmission in industrial
applications requiring high-bandwidth connectivity. In addition to 4 Giga RJ-45 ports, the
switch is equipped with 5 Giga RJ-45/SFP combo ports to deliver maximum throughput and
ÀH[LELOLW\IRUKLJKGHQVLW\FRQQHFWLRQZKLOHSURYLGLQJ*LJDXSOLQNRU*LJD5LQJFRQQHFWLRQ
With the Korenix patented MSR technology, users can aggregate up to 4 Multi Gigabit Rings
into a single switch and ensure network reliability in applications with increased bandwidth
and expended system. Furthermore, JetNet 6059G supports advanced management and
security features, such as LLDP and JetViewPro, 4 Priority queues per port, 256 VLANs,
IGMP Snooping, DHCP, LACP to ensure high performance network communication. JetNet
6059G is compliant with NEMA -TS2 /Maritime, Railway standards and has dual redundant
10.5~60VDC power inputs and -40~75OC wide operating temperature range to work reliably
under vibrating and shock environments in Maritime, Railway or rolling stock applications.
Package Checklist
8QSDFNWKHER[\RXZLOO¿QG
JetNet 6059G with DIN Rail kit x1
Quick Installation Guide
Console Cable (RJ-45 /DB9)
Wall Mount kits
Mounting the Unit
Din-Rail mount: Mount the din-rail clip on the rear of
JetNet 6059G on the DIN rail.
For information about the DIN Rail installation, please
refer to user’s manual.
JetNet 6059G Series
Industrial 9-portGigabit Managed
Ethernet Switch
Quick Installation Guide
www.korenix.com
V1.0
Grounding JetNet 6059G
There is one grounding screw on the bottom side
of JetNet 6059G. Connect the frame grounding
of JetNet 6059G to the grounding surface to
ensure safety and prevent noise to interfere
communication.
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+ and V- contact on the terminal block
connector.
Wiring the Relay Output (DO)
The relay output contacts are in the bottom side as shown on Figure-3. The relay output (DO)
LVFRQWUROOHGE\WKHSUHGH¿QHGRSHUDWLQJUXOHV7RDFWLYDWHUHOD\RXWSXWIXQFWLRQSOHDVHUHIHUWR
the User’s Manual for the Relay Output information.
2. Tighten the wire-clamp screws to prevent the power wires from being loosened.
Notes: The recommended working voltage is DC 24V (Input range: DC10.5~ 60 V),
maximum power consumption is 20 Watts.
Note: The relay contact only
supports 1A current, DC 24V.
It is not recommended to apply
voltage and current higher than
WKHVSHFL¿FDWLRQV
Figure-3
Wiring the Digital Input (DI)
The Digital Input (D.I.) contacts are in the bottom side of the device as shown in Figure-4.
,WDFFHSWVRQHH[WHUQDO'&W\SHVLJQDOLQSXWDQGFDQEHFRQ¿JXUHGWRVHQGDOHUWPHVVDJH
through Ethernet when the signal is changed.
Note: the DI accepts DC type signal and supports isolated input circuit with Digital High
Level input DC 11V~30V and Digital Low Level input DC 0V~10V. Don’t apply higher
YROWDJHWKDQWKHVSHFL¿FDWLRQLWPD\FDXVHLQWHUQDOFLUFXLWGDPDJHRUDZURQJDFWLRQRI',
Connecting to Network
1. Connecting the Ethernet Port: Connect the Ethernet port of JetNet 6059G with the
other Ethernet device by Cat-5/Cat-6 UTP or STP cable, and then the LNK/ACT LED will
WXUQRQDQGVWDUWÀDVKLQJWRLQGLFDWHWKHFRPPXQLFDWLRQLVRFFXUUHGEHWZHHQGHYLFHV
2. Connecting the SFP Port:3OXJLQ6)3¿EHUWUDQVFHLYHU:HUHFRPPHQGXVLQJ.RUHQL[
FHUWL¿FDWHG6)3PLQL*%,&WUDQVFHLYHU&URVVFRQQHFWWKHWUDQVPLWFKDQQHODWHDFKHQGWR
the receive channel at the opposite end as illustrated in the Figure-5.
Figure-5
Ǽ
This is a Class 1 Laser/LED product.
Don’t looke into the Laser/LED Beam.
TX
RX
AB
TX
RX
ATTENTION
Figure-4
Device Management
-HW1HW*,QGXVWULDO 0DQDJHG 6ZLWFKSURYLGHVERWKLQEDQGDQGRXWEDQGFRQ¿JXUDWLRQ
PHWKRGV<RXFDQFRQ¿JXUHWKHVZLWFKYLDWKH56FRQVROHZLWKWKHDWWDFKHGFRQVROH
cable. Or you can remotely manage the switch via network. You can choose Telnet/SSH,
Web/HTTPS management.
1. Preparation for console management: Attach the RS-232 DB9 connector to your PC’s
COM port. Connect the RJ-45 connector to the console port of the JetNet 6059G
Go to Start -> Program -> Accessories -> Communication -> Hyper Terminal
Give a name to the new console connection.
Choose the COM name and select the correct serial settings. The serial port settings of
JetNet 6059G are as below: 9600bps, No parity check, 8 Data bits, 1 stop bit
After connected, you will see the Switch login request. Type the username and password
then you can login. The default username is “admin”, password is “admin”.
)ROORZWKHPDQXDOWRFRQ¿JXUHWKHVRIWZDUHIHDWXUHV
2. Preparation for Web management: Before you attempt to use the embedded web
interface to manage switch operation, verify that JetNet 6059G is properly installed on your
network and that every PC on this network can access the switch via the web browser.
Launch the web browser (Internet Explorer or Mozilla Firefox) on the PC.
Type http://6059G_IP_Address (The default IP address is 192.168.10.1.) then press Enter.
The login screen will appear next.
Type in the user name and password and click
“OK” button. The welcome page of the Web-Based
management interface will appear then. The default
user name and password is admin/admin
Korenix Customer Service
KoreCARE is Korenix Technology’s global service center, where our professional staffs are
ready to answer your questions at any time.
At the left column of the web management interface
are the software features, where ring column will
list the available settings.
For more operating instructions, please refer to
the User’s manual of JetNet 6059G included in the
packing or downloadable from the Korenix Website
– www.korenix.com.
Ᾰ䘦
JetNet 6059G㌱ࡍᱥжⅴޞݼ㖇㇗ශᐛѐԛའ㖇Ӛᦘᵰθ9Ѡݼㄥθ᭥ᤷ32GӚᦘ
㜂ᶵθѰ儎ᑜᇳᐛѐᓊ⭞ᨆב儎䍞ᮦᦤՖ䗉ᵃࣗȾ䲚Ҽ4ѠݼRJ-45ㄥθӚᦘᵰ䘎䞃༽
5ѠݼRJ-45/SFP combo䘿ㄥθᨆבᴶཝ䠅ૂ⚫⍱ᙝθѰ儎ᇼᓜ㖇㔒ᨆבݼр
㚊ᡌݼ⧥㖇䀙ߩᯯṾȾ᭥ᤷKorenixщMSR⧥㖇ߍ֏ᢶᵥθ⭞ᡭ൞ঋӚᦘᵰр᮪4
Ѡݼ⧥㖇θуӻ⺤ؓᐛѐ⧦൰㖇㔒Ⲻ䶖ᙝθ䘎㜳ᨆᑜᇳᢟኋ㌱㔕ᶺȾ↚ཌθJetNet
6059G䘎᭥ᤷޞ䶘Ⲻ儎㓝㖇㇗ࣕ㜳ૂᆿޞᵰθׁྸLLDPঅ䇤ૂJetViewPro㇗⨼䖥Ԭθ∅ㄥ
᭥ᤷ4ѠՎݾ㓝θ256ѠVLAN㓺θIGMP SnoopingθDHCPθLACPㅿθ⺤ؓ㖇㔒䙐䇥ⲺՎ
䍞儎᭾ȾJetNet 6059G┗䏩NEMA -TS2 /⎭Ӂᓊ⭞θ䫷䐥ᓊ⭞ḽθᒬ᭥ᤷ10.5Њ60VDCߍ
֏⭫Ⓠ䗉ޛૂ-40~75OCᇳᐛ֒⧥ູθ൞儎ᥥࣞ儎ߨ࠱⧥ູⲺ⎭Ӂθ䫷䐥θ〱ࣞ䖜䖼ᓊ⭞ѣ
⺤ؓ㖇㔒Ⲻ䶖ᙝȾ
⺢Ԭᆿ㻻
ᢉᔶ㻻Ỷḛ䞃Ԭ:
JetNet 6059Gδሲ䖞ε
ᘡ䙕ᆿ㻻ሲ
㓵㔼(RJ-45 /DB9)
ᤸᆿ㻻䞃Ԭ
䇴༽ᆿ㻻
ሲ䖞ᆿ㻻: ⭞JetNet 6059Gᵰ䓡㜂䶘Ⲻሲ䖞ሼ䇴༽গр
ሲ䖞Ⱦᴪཐሲ䖞ᆿ㻻ؗᚥθ䈭৸㘹⭞ᡭᬃ֒ᢁ߂Ⱦ
CH
JetNet 6059G Series
Industrial 9-portGigabit Managed
Ethernet Switch
Quick Installation Guide
www.korenix.com
V1.0
JetNet 6059G䇴༽൦
JetNet 6059Gᵰ䓡ᓋ䜞ᴿжѠ൦㷰ѓȾሼ൦㓵㷰
ѓ൦θ⺤ؓ䇴༽ᆿޞθ䱨↘⭫≊ᒨᢦȾ䇴༽ᵠ
൦θഖ㠠❬ഖ㍖䙖ᡆᦕᇩθሼуҾԛؤགྷȾ
⭫Ⓠ䘔
1. ሼ⭫ⓆⲺ↙䍕ᶷᕋ㓵࠼ࡡޛ䇴༽ᓋ䜞⭫Ⓠ㓵″ⲺV+ૂV-ㄥȾ
Relay Output (DO)㔝⭫ಞᣛ䆜䘔
ྸഴ-3ᡶ⽰θ㔝⭫ಞᣛ䆜䀜⛯փӄᵰ䓡ᓋ䜞ȾRelay Output (DO)㔝⭫ಞᣛ䆜ṯᦤ人ᇐѿⲺу
ᬃ֒ᶛ䀜Ⱦྸࣞ㔝⭫ಞᣛ䆜ࣕ㜳θ䈭৸ⵁ⭞ᡭᢁ߂㔝⭫ಞᣛ䆜ࣕ㜳䈜䀙Ⱦ
2. ᤝ㍝㷰ѓθ䱨↘⭫Ⓠ㓵㝧㩳
༽⌞: ᧞㦆ᐛ֒⭫ুѰDC 24V (䗉ޛ⭫ু㤹പ: DC10.5~ 60 V), ᴶཝࣕ㙍20W.
༽⌞:㔝⭫ಞᣛ䆜䀜⛯ӻ᭥ᤷ1A⭫
⍷θDC 24V⭫ুȾ䈭ֵ⭞儎ӄ
↚㿺ṲⲺ⭫ু⭫⍷Ⱦ
ഴ-3
Digital Input (DI)ᮦᆍ䗉ޛ䘔
ྸഴ-4ᡶ⽰θᮦᆍ䗉ޛ䀜⛯փӄᵰ䓡ᓋ䜞Ⱦᆹж䐥ཌ䜞DCؗ䗉ޛθᖉؗᰬ
䘷ᣛ䆜ؗᚥȾ
㖇㔒䘔
1. 䘔ԛའ㖇ㄥ: ⭞Cat-5/Cat-6ኅ㭳ᡌ䶔ኅ㭳㔔㓵䘔JetNet 6059GⲺ㖇ૂެᆹԛའ
㖇䇴༽θࡏLNK/ACT LED⽰⚥ՐӤ䎭ᒬ䰠⛷θ㺞⽰њѠ䇴༽ҁ䰪↙൞䙐䇥Ⱦ
2. 䘔SFPㄥ: ᨈޛSFPݿ㓚᭬ಞ⁗ඍȾ᧞㦆ֵ⭞㔅Korenix⎁䈋䇚䇷ⲺSFP mini GBIC
ݿ㓚᭬ಞ⁗ඍȾྸсഴ5ᡶ⽰θሼ䘷ㄥ䘔ࡦⴤⲺ䇴༽Ⲻ᭬ㄥθ䘑㺂Ӛӈ䘔Ⱦ
ഴ-5
༽⌞: DIDCؗ䗉ޛθ䙱䗇1φDC11V~30Vθ䙱䗇0φDC 0V~10VȾ࠽ֵ⭞儎ӄ↚㿺
ṲⲺ⭫ুθࡏ㜳ሲ㠪䜞ഔ䐥ᡌ䙖ᡆDI᭻䳒Ⱦ
ഴ-4
Ǽ
↚ѰClass 1 Laser/LEDݿӝθ
࠽㿼◶ݿᶕȾ
TX
RX
AB
TX
RX
⌞ᝅ
䇴༽㇗⨼
JetNet 6059G㖇㇗ශᐛѐԛའ㖇Ӛᦘᵰ᭥ᤷᑜ(in-band)ᑜཌ(out-band)䇴㖤⁗ᕅȾ⭞ᡭ
ԛ䙐䗽RS232ㄥሯӚᦘᵰ䘑㺂䇴㖤θᡌ䙐䗽㖇㔒䘑㺂䘒ぁ㇗⨼Ⱦᛞ䘎ԛ䘿Telnet/
SSH, Web/HTTPSཐ〃㇗⨼⮂䶘Ⱦ
1. Console㇗⨼Ⲻ༽ᐛ֒: ሼRS-232 DB9ཪㄥ䘔ࡦ֖䇗㇍ᵰⲺCOMθሼRJ-45ㄥᨈޛ
JetNet 6059GⲺConsleㄥȾ
䘆㺂Start(ࣞ) -> Program(ぁᓅ) -> Accessories(䱺Ԭ) -> Communication(䙐䇥) -> Hyper
Terminal(䎻㓝㓾ㄥ)
䘿COMㄥθ䇴ᇐ↙⺤ⲺѨ৸ᮦȾJetNet 6059GⲺѨ৸ᮦ䇴ᇐྸс:
⌘⢯⦽φ9600bps, ṗ僂փφᰖ, ᮦᦤփφ8, ڒ↘փφ1
䘔θՐ࠰⧦ӚᦘᵰⲺⲱᖋᨆ⽰Ⱦ䭤ޛ⭞ᡭᇼ⸷ⲱᖋȾ唎䇚⭞ᡭᱥćadminĈθ
ᇼ⸷ᱥćadminĈȾ
䈭ṯᦤ⭞ᡭᢁ߂䘑㺂ࣕ㜳䇴㖤Ⱦ
2. Web㇗⨼༽ᐛ֒: ൞ֵ⭞㖤Web⮂䶘ሯӚᦘᵰᇔ᯳㇗⨼ҁࢃθ䈭ݾ僂䇷JetNet 6059Gᐨ
㔅↙⺤ޛ㖇㔒θъ㖇㔒ѣⲺԱᝅ䇗㇍ᵰ䜳ԛ䙐䗽Web⎅㿾ಞ䇵䰤ӚᦘᵰȾ
ࣞ䇗㇍ᵰрⲺ⎅㿾ಞ (IE⎅㿾ಞᡌMozila Firefox)Ⱦ
൞൦൶ṅ䭤ޛhttp://6059GⲺIP൦൶ (唎䇚ⲺIP൦൶ᱥ192.168.10.1.)❬ഔ䖜ȾՐ࠰⧦ⲱᖋネ
Ⱦ
䭤ޛ⭞ᡭૂᇼ⸷θ⛯࠱ćOKĈ䭤θࡏՐ࠰⧦web
㇗⨼⮂䶘Ⲻѱ享Ⱦ唎䇚Ⲻ⭞ᡭૂᇼ⸷ᱥadmin/
adminȾ
Other manuals for JetNet 6059G
4
Table of contents
Other Korenix Switch manuals
Korenix
Korenix JetNet 3906G User manual
Korenix
Korenix JetNet 5728G series User manual
Korenix
Korenix JetNet 6710G-HVDC Series User manual
Korenix
Korenix JetNet 3008f v3 User manual
Korenix
Korenix JetNet 5628G Series User manual
Korenix
Korenix JetNet 3705-24V User manual
Korenix
Korenix JetNet 3018G Series User manual
Korenix
Korenix JetNet 3212G-2C2F User manual
Korenix
Korenix JetNet 3808G-M12 Series User manual
Korenix
Korenix JetNet 5428G Series User manual
Korenix
Korenix JetNet 4508i Series User manual
Korenix
Korenix JetNet 3018G Series User manual
Korenix
Korenix JetNet 3810G(f) User manual
Korenix
Korenix JetNet 5428G-20SFP Series User manual
Korenix
Korenix JetNet 3810G Series User manual
Korenix
Korenix JetNet 3808G Series User manual
Korenix
Korenix JetNet 4706 User manual
Korenix
Korenix JetNet 3505 User manual
Korenix
Korenix JetNet 5710G Series User manual
Korenix
Korenix JetNet 5210G User manual
