Kollmorgen SERVOSTAR 400 User manual
SERVOSTAR®400
Quickstart Guide
Version 12.2010
Keep all manuals as a
product component during
the life span of the product.
Pass all manuals to future
users/owners of the product.
Preparation
The CD-ROM delivered with the servo amplifier contains all the manuals in PDF for-
mat and the setup software. Insert the CD-ROM into your PC.
Autostart function activated: A window with the start screen opens.
Autostart function deactivated: Click START (task bar), then on Run. Enter
x:\index.htm or x:\autorun.exe (x = CD drive letter). Click OK. The start screen
opens.
Install Setup Software
On the start screen you find a link to the setup software:
Install Setup Software SERVOSTAR S400/S600 Release _.__ Build __
Click it and follow the instructions from here.
Documents
You need Acrobat Reader to read the PDFs (installation link on every screen).
Select the language version on the start screen of the CD-ROM. Click "Servo Drives"
in the column "Technical Manuals". A table with links to all manuals appears.
Mechanical and Electrical Installation of the Servo Amplifier
1. Unpack servo amplifier and accessories
2. Keep the instructions manual ready (print if necessary)
3. Observe safety instructions in the manuals
4. Mount the servo amplifier as described in the instructions manual
5. Wire the servo amplifier as described in the instructions manual or apply the mini-
mum wiring for drive test (see next page)
2
Minimum Wiring for Drive Operation
3
Motor
Motor-Power
Feedback
RES
ENC
PC
Power
24V DC
-
1
2
24V ON
4
5
+
Enable
3
Power ON
Motor-Power
Feedback
Motor
1
2
This wiring does
not fulfill any
requirements to
safety or
functionality of
your application,
it just shows the
required wiring
for drive testing
without load.
Connect
lConnect the interface cable to a serial interface on your PC and to the serial in-
terface X6 of the servo amplifier. USB to serial converter can be used optionally.
lSwitch on the 24 V logic power supply for the servo amplifier.
lWait about 30 seconds, until the front display of the servo amplifier displays the
current rating (e.g. for 3 amps). If the mains power supply voltage is
switched on, too, a leading P is displayed (e.g. for Power, 3 amps).
If a fault code ( ) or a warning ( ) or a status message ("." or "_"
or "E" or "S") appears in the display, you will find the description and hints for
trouble shooting in the instructions manual. If there is fault, fix the problem.
Double-Click the Drive.exe icon on your Windows desktop to start the
software.
"Multidrive" must be activated in the
menu "Communication"!
You can work offline or online with
Drive.exe. We work online now.
Select the interface where the servo
amplifier is connected to.
4
The software tries to com-
municate with the drive
and to upload the param-
eters. If it's not success-
ful, you receive this error
message:
Frequent causes:
- wrong interface chosen
- wrong connector chosen at the servo amplifier
- interface is used by another software
- 24 V auxiliary voltage for the servo amplifier not working
- interface cable broken or wrong wiring
Click OK to remove the error message. Detect and remove the error source. Restart
the software.
If communication works, the drive selection screen appears:
The master and axis modules, recognized in the
system, with its station address and name are
listed. The master module is separately charac-
terized.
Doubleclick on the amplifier, which you want to
work with.
You can select additional other axis modules
later to show them in parallel at the screen and
parameterize them (Multidrive function).
Now parameters are transmitted from the servoamplifier to the computer. Then you
see the start screen.
Make sure, that the amplifier is disabled (Input HW-Enable connector X1 pin 3
must be0Voropen)!
5
Important Screen Elements
Help Function
The Online-Help gives detailed information to all parameters the servo amplifier can
work with.
Key F1 Starts Online Help for the actual screen page.
Menu Bar ? / Online HTML Help Starts Online Help with table of contents.
Tool Bar
Save to EEPROM,
required if you changed parameters.
Reset (coldstart),
required if you changed important configuration parameters.
Operation Mode, use Digital Velocity mode for
drive testing.
Disable and Enable of the amplifier's output
stage via software.
Status Bar
6
Basic Setup
On the start screen click "Basic Setup" button.
Regen Resistor: Change only if you use an external regen resistor. Most applica-
tions don't need an external regen resistor
Max. Mains Voltage: Select the nominal mains AC voltage
Mains Phase Missing: You can select either warning "n05" or error "F19" in case of
phase loss. The setting "F19" disables the output stage, "n05" is just a message.
Units: Acceleration, Velocity, Position
Select usable units for your application referring to the moved load.
Address: Adjust for master amplifier only (= highest address of the drive system, see
instructions manual: "Setup/Multi-Axis Systems")
Leave all other fields unchanged. Click OK.
7
Motor (synchronous)
On the start screen click "Motor" button.
Press function key F12 (Software Disable).
Motor Type: Select Synchronous Motor. If you use a linear motor or an induction
motor, please contact our support department.
Number-Name: Click the list to start uploading the motor parameter table, which is
stored in the servo amplifier. Search and select the connected motor. If your motor is
not listed, please contact our support department.
Leave all other fields unchanged.
Click OK.
8
If your motor has a built-in brake, click
"Yes", otherwise "No".
If Software Enable is active, a warning ap-
pears. You can proceed, but after the ampli-
fier is restarted, you must check whether the
holding brake configuration is correct.
Click OK.
Parameters are uploaded to the ampli-
fier's RAM now (takes some seconds).
When this is done, you have to accept
the changed configuration with "Yes" or
to discard the changes in the appearing
screen.
If you click "Yes", the parameters are
saved in the EEPROM and the ampli-
fier makes a coldstart (reset). This
takes some seconds.
9
Feedback
On the start screen, click "Feedback" button.
Press F12 (disable) before changing feed-
back parameters.
Feedback Type:
Select the feedback type used.
Leave all other fields unchanged.
If Software Enable is active, a warning
appears. The configuration change
cannot be performed. Click OK on the
warnings, press F12 (SW disable)
and start the Feedback procedure
again.
If everything was ok, the same procedure
(parameter upload) that has been described
for the motor selection starts.
If you click "Yes", the parameters are saved
in the EEPROM and the amplifier makes a
coldstart (reset). This takes some seconds.
10
Other manuals for SERVOSTAR 400
1
Table of contents
Other Kollmorgen Servo Drive manuals
Kollmorgen
Kollmorgen BDS4 Series User guide
Kollmorgen
Kollmorgen AKMH Series User manual
Kollmorgen
Kollmorgen AKD2G-S Series User manual
Kollmorgen
Kollmorgen S20260 User manual
Kollmorgen
Kollmorgen AKD-x00306 User manual
Kollmorgen
Kollmorgen AKD PDMM series User manual
Kollmorgen
Kollmorgen AKD PDMM User manual
Kollmorgen
Kollmorgen AKD 2G User manual
Kollmorgen
Kollmorgen AKD EtherCAT User manual
Kollmorgen
Kollmorgen SL3000 User manual
Kollmorgen
Kollmorgen MKD-C Series Operating manual
Kollmorgen
Kollmorgen AKD-CC User manual
Kollmorgen
Kollmorgen AKM Series User manual
Kollmorgen
Kollmorgen EB-8902 Manual
Kollmorgen
Kollmorgen AKD series User manual
Kollmorgen
Kollmorgen P70530 User manual
Kollmorgen
Kollmorgen AKM1 User manual
Kollmorgen
Kollmorgen SERVOSTAR 300 Installation and operating manual
Kollmorgen
Kollmorgen S70101 User manual
Kollmorgen
Kollmorgen AKD User manual
