Kohler DK2 POWER OPC566E User manual
CHIPPER ASSEMBLY GUIDE
MODEL: OPC566E
6 INCH KINETIC DRUM CHIPPER
DETAIL K2 INC.
DK2 POWER USA
4301 S Valley View Blvd STE 10-11
Las Vegas, NV 89103
1-702-331-5353
KINETIC DRUM
DOT TOWABLE
KOHLER ENGINE
6IN KINETIC DRUM CHIPPER
REV 1 –9-19-2019
DETAIL K2, INC.
1080 Clay Avenue Unit 2
Burlington, Ontario, Canada L7L0A1
DK2 USA EAST
6245 Industrial Parkway
Whitehouse, OH 43571
PARTS AND SERVICE 702-331-5353 OR WWW.DK2POWER.COM CONTACT US
OPC566E 6 INCH
KINETIC DRUM CHIPPER
STEP 1:
Open and unpack all items. Leave lots of working space.
Inspect all parts.
The CHIPPER is shipped in a crate. Remove all sides before
you begin.
NOTE: UPON INSPECTION OF PARTS IF YOU FIND ANY DAMAGE OR MISSING
PARTS PLEASE CALL DK2 POWER AT 702-331-5353 OR CONTACT US VIA
OUR WEBSITE WWW.DK2POWER.COM
WE WILL REPLACE ANY MISSING PARTS TO YOU FREE
PLEASE DO NOT RETURN TO THE STORE
REV 1 –9-19-2019
STEP 2:
1. PREPARE TO INSTALL THE AXLE
2. Slide chipper body to hang off side of the crate as shown.
3. Have a helper tip the unit forward while you complete the
next step.
Extend the unit off the crate
REV 1 –9-19-2019
STEP 3:
1. Tip the unit forward
2. Install the axle using the 2 bolts and hardware provided and
tighten.
REV 1 –9-19-2019
2 BOLTS AND NUTS
STEP 4:
1. INSTALL THE WHEELS
2. Place the 2 black spacers on the axle first
3. Install the 2 wheel with nuts
4. Wheels should spin free.
5. Install end caps
Spacers
REV 1 –9-19-2019
End Cap
Washer then Nut and Pin
STEP 5:
1. INSTALL FEED CHUTE
2. With a helper slide the feed chute hinge pins into place,
close and latch.
REV 1 –9-19-2019
STEP 6
1. Holding the feed chute, lay the unit down as shown
2. Prepare to install the front hitch assembly.
REV 1 –9-19-2019
STEP 7
1. Install the front hitch assembly
2. Use 8 bolts and hardware provide and secure tightly
Use bolts provided both sides
REV 1 –9-19-2019
STEP 8
1. Install the articulated front wheel assembly
2. Use bolt and pin hardware provide and semi tight to allow
assembly to raise and lower.
3. Raise and pin when towing
PIN
REV 1 –9-19-2019
BOLT
STEP 9
1. Install the TOW BAR
2. Use 2 bolts and hardware provide and secure tightly
3. Tip unit forward and lower to level
Use 2 bolts provided
REV 1 –9-19-2019
Table of contents
Other Kohler Chipper manuals
Popular Chipper manuals by other brands
Value Leader
Value Leader z9400 Assembly, operation and parts manual
Timberwolf
Timberwolf TW 230HB instruction manual
Salsco
Salsco 600PTO Operator and parts manual
Cub Cadet
Cub Cadet 24A-424M710 Operator's manual
Champion
Champion 91050 Owner's Manual and Operating Instructions
Kellfri
Kellfri 13-WC17H2 operating instructions