Kogan KAPRNTPKLBA User manual
PORTABLE POCKET
BLUETOOTH LABEL PRINTER
KAPRNTPKLBA
2
Safety & Warnings
3
Components
4
Overview
4
Operation
7
Cleaning & Care
15
Troubleshooting
16
Specifications
17
Notes
18
3
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions.
1. This device may not cause harmful interference and
2. this device must accept any interference received, including interference that may
cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Notes:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
SAFETY & WARNINGS
WARNING: RF warning for Portable device:
• The device has been evaluated to meet general RF exposure
requirement.
• The device can be used in portable exposure condition without
restrictions.
4
Label Maker
User Guide
USB Charging Cable
COMPONENTS
OVERVIEW
Paper compartment
cover
Window
Paper
compartment
Print head
Paper exit
Slider cutter
Indicator
Power Button
Charging port
5
Label paper
Various label paper is are available for purchase for this printer.
The label paper features an ‘easy tear’ line, to help peel off the adhesive backing.
Gently bend the label paper along the ‘easy tear’ line to make it easier to peel the bottom
paper from the adhesive.
Cut paper
Continuous paper
Continuous paper printing surface
Back of continuous paper
Easy tear line
Bottom paper
Easy tear line
Adhesive
6
Power Button and Indicator
Power button
Button
Operation method
Functions
Power button
Press and hold for 3s
Turn On/Off
Short press
Print out the paper
Double press
Print the content of the
self-test paper
Indicator status
Solid Green
Normal status
Slowly flashing Green
Charging with power on
Rapidly flashing Green
Charging with power off
Solid Red
Error (low paper, cover opened, high
temperature)
Slowly flashing Red
10% battery
Rapidly flashing Red
5% battery
Indicator
7
1. Open the paper compartment cover.
2. Place the label paper in the paper
compartment with the printing side
facing up.
3. Pull out approximately 5mm of the
label paper.
4. Align the tabs on the cover with the
holes in the printer and close the cover.
5. Press and hold the power button for 3s
to turn on.
6. Short press the power button to
identify the label position.
OPERATION
Printing side faces
toward this direction
About 5mm
8
7. The printer will eject a small amount of
paper. Paper installation is completed.
8. After printing a label, slide the cutter
up to tear off the label.
Notes:
• When installing or replacing the label roll for the first time, the label position
identification is required; (Step 6.).
• If the label position identification is not carried out, failures may occur such as first
printing missing, not centred etc.
• When using, continuous paper, if will not be required to press the power button for
positioning. Instead, pull the paper until it is in position.
Download the Print Master App
Print master
Notes:
• This product requires the Print Master App to operate.
• Android mobile phone will need to enable GPS and confirm the authorisation.
9
Use your mobile phone to scan the QR
code to download the APP.
Alternatively, search for “Print Master” in
the App Store (iOS) or Google Play Store
(Android) and download.
Pair the Label Printer to your Phone
1. Turn on GPS (Android mobile phone only)
2. Open the App
3. Click “Connect now” to search for your
device
4. Once connected the label printer
is ready to be used.
Note: When connecting device in the App, make sure that your Label Maker is turned on
and Bluetooth is enabled on your mobile phone.
Print master
Privacy
Location Services:
On
10
Confirm the Label Size
Method 1: Check the sticker on the label
paper.
Method 2: Check the label paper
packaging
Method 3: Use a ruler to measure
Method 4: Check the label paper pads.
Product: Pattern label
Model: DP-P06
Detail: Seal, Snow fox
Spec: 12 x 40mm/210pcs
Quantity: 3
40mm
12mm
Table of contents
