Kodak Ektalite E30 User manual
Overhead Projector
Instructions
Bedienungsanleitung
Instrucciones de
operación
1KODAK EKTALITE E30/E31 OVERHEAD PROJECTORS
ENGLISH
CONTENTS
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . 2
Names of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Using the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Lamp Replacement . . . . . . . . . . . . . . . . . . . . . . . . 7-8-9
Fuse Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2KODAK EKTALITE E30/E31 OVERHEAD PROJECTORS
Important Safety Instructions
Read all instructions before using the projector.
Follow the safety instructions below when using the over-
head projector.
• Do not allow children to operate this unit.
• Do not touch hot parts near the lamp housing.
• Do not operate a damaged unit or disassemble the unit by yourself.
• Use a qualified service technician when repair is required. Incorrect
assembly can cause electric shock.
• Keep the power cord away from hot surfaces. If the power cord is dam-
aged have it repaired before using.
• If it is necessary to use an extension power strip, use one which is fuse
and safety certified.
• Disconnect the power plug when not in use. Pull on the plug, not the
cord, when disconnecting from the power source.
• Make sure the unit is completely cooled before storage.
• Place the projector on a flat and stable surface.
• To prevent electric shock, do not operate the unit if it is wet or on a wet
surface.
• Disconnect the power cord from the power source before removing the
lamp.
• Do not touch the projection lens while the lamp is on.
• Do not obstruct the ventilation area.
• Always open the projection head before operating the unit. Trapped heat
can cause mirror damage.
• Do not look directly at projected light to prevent eye damage.
• Do not use the unit for purposes other than projection of transparencies
or LCD panels.
• Use only the lamp as indicated on the label inside your projector. Use of
improper lamp can result in damage or poor performance.
3KODAK EKTALITE E30/E31 OVERHEAD PROJECTORS
ENGLISH
Names of Parts
4KODAK EKTALITE E30/E31 OVERHEAD PROJECTORS
Set Up
ARM RETAINER CLIP
1. Press the ARM RETAINER CLIP to
release the arm.
2. Rotate the FOCUS KNOB to move
the head slightly away from the
housing.
3. Lift the arm into the full, upright
and locked position and open the
PROJECTION LENS head.
5KODAK EKTALITE E30/E31 OVERHEAD PROJECTORS
ENGLISH
Using the Projector
1. If using an LCD panel, install it and turn it on first.
2. Plug overhead projector in and turn the POWER SWITCH to the “ON”
position.
3. Place a flat transparency on STAGE GLASS as shown and center it.
6KODAK EKTALITE E30/E31 OVERHEAD PROJECTORS
Using the Projector
4. Adjust the PROJECTION LENS head angle to center the image on the
screen.
5. Turn the FOCUS KNOB until the projected image is sharp.
Should an orange or blue fringe appear around the outer edge of the
projected image, turn the COLOR FRINGE KNOB to clear it.
6. When the lamp is burned out, use the LAMP CHANGE HANDLE to
switch to new lamp.
The power is cutoff automatically during lamp change; switch power on
again after using lamp switch.
NOTE:
Remember to replace the old lamp with a new one before next use.
Do not remove lamp until it is completely cooled.
7KODAK EKTALITE E30/E31 OVERHEAD PROJECTORS
ENGLISH
Category of Lamp: EVD(36V/400W)/EHJ(24V/250W)/EYB(82V/360W)
Note: Use only the lamp type that is named on the label inside the projector.
Model Lamp AC Input Voltage Lamp Voltage Watt
E3O
EYB 120V 32V 360W
EHJ 230V 24V 250W
E31 EVD 120/230V 36V 400W
Using lamps of higher wattage than indicated on the label can cause
damage.
Lamp Replacement
8KODAK EKTALITE E30/E31 OVERHEAD PROJECTORS
Lamp Replacement
LAMP HOUSING COVER
LAMP HOUSING CLIP
1. Turn POWER SWITCH “OFF.”
2. Unplug power cord.
Wait for lamp to cool before removal.
3. Open and remove the TOP COVER.
4. Open the LAMP HOUSING COVER.
This manual suits for next models
1
Table of contents
Languages:
Other Kodak Projector manuals
Kodak
Kodak Carousel S-AV 1030 User manual
Kodak
Kodak KP1300X User manual
Kodak
Kodak DP1050 ULTRA User manual
Kodak
Kodak Carousel S-AV1000 User manual
Kodak
Kodak Carousel 4200 User manual
Kodak
Kodak EKTAGRAPHIC III User manual
Kodak
Kodak EKTAGRAPHIC III User manual
Kodak
Kodak EKTAPRO 9020 CINE User manual
Kodak
Kodak V600 User manual
Kodak
Kodak Pocket Portable Projector User manual
Kodak
Kodak DP2900 - Digital Projector User manual
Kodak
Kodak EKTALITE User manual
Kodak
Kodak Carousel S-AV 2050 Operating manual
Kodak
Kodak Pocket Portable Projector User manual
Kodak
Kodak EKTALITE User manual
Kodak
Kodak FLIK HD9 User manual
Kodak
Kodak FLIK X7 User manual
Kodak
Kodak EKTAGRAPHIC AFT User manual
Kodak
Kodak FLIK X4 User manual
Kodak
Kodak DP850 - Ultra Digital Projector Quick start guide
