KISAG AG
Bahnhofstrasse 3
H-4
12 B
ll
h
Tel. +41
2 617
2 60
Fax. +41
2 617
2 7
E-Mail: kisa
kisa
.ch Internet: http://www.kisa
.c
.
.
Kisa
item no. 8210 Total len
th:
76 cm/30 in.
Power: 230VAC / 550 W Depth of insertion: 50 cm/20 in.
Frequency: 50 Hz Length of cord: 4 m/13 ft.
Idling:
17000 r.
.m., 14000 r.
.m. Wei
ht:
4 kg/8.8 lb.
In operation:
10000 r.
.m., 8000 r.
.m
Safet
re
ulations for appliances EN 60
5 -
EN 60335 - 2 - 64
Emission standarts EN 55011
EN 61000 - 3 - 2
EN 61000 - 3 - 3
Interference immunity standards EN 61000 - 4 - 2 EN 61000 - 4 - 6
EN 61000 - 4 - 4 EN 61000 - 4 - 11
EN 61000 - 4 - 5
v
th
in
tr
ti
n
Holdin
scre
21
.
4
h
f
Blades com
let
21
.21
l
r
n
h
ft
21
.
F
R
t
in
r n
Hand blender item no.
210
En
lis
r m
n
r
i
n
1
2
Safet
instruction
Pr
t f
t
r
Specifications and testin
Service and Warrant
Safet
instructions must alwa
s be followed in order to
prevent dama
es resultin
from the use of this appliance
Appliance must only be operated by
staff trained in its operation.
Do not operate hand blender after
the appliance malfunctions or if it is
damaged in any manner. Contact
our customer service or the nearest
service facility in such case.
Blades are extremely sharp and
may cause cut injuries. Wear
suitable protection gloves!
NEVER dismantle or try to repair the
appliance. Do not insert anything
into the openings of the appliance.
Do not use hand blender for other
than intended use. In order to
prevent injuries or damages
appliance must onl
be repaired b
r
t
m
r
rvi
r
n
th
riz
rvi
ntr
Case of emer
enc
Unplu
from outlet immediatel
A
liance is intended for industrial use
in large containers.
At the end of its operating life appliance
should be recycled or disposed of
properly
– Do not touch power cord when your
hands are wet.
– Do not remove plug from outlet by
pulling the cord.
– Do not clean cord using water and do
not immerse in water or other liquid.
– Do not damage power cord and keep
awa
from hot or sharp parts etc.
Do not o
erate hand blender if it i
Blades and shaft sealin
are wearin
parts and need to be checked on a re
ular basis
It is recommended that the shaft seal
item no. 8210.304
is to be replaced when worn out or after two
ears.
Replacement of seal:
Loosen the holding screw and remove blades, pierce old seal with screwdriver and pull out. Clean shaft and
boring with a cloth, lubricate new sealing with food safe lubricant and push protruding seal over the shaft
towards the blades. Push the seal with blender blades in ori
inal position and ti
hten the blades in to positio
t th
h
f
s countersink with the holdin
screw
Terms of warranty:
Within a period of two years from the date indicated on the sales receipt any appliance or parts thereof, with
proven defects in material and workmanship, will be repaired or replaced at no charge. This warranty does not
cover any damages caused by misuse, damaged parts or repair service other than those which have been
authorized, wear or consequential damages. The appliance has to be returned to Kisag AG CH-4512 Bellach
or to a service facility chartered by Kisag. immediately after detection of a defect including a copy of the sales
receipt and a description of the defect detected. Shipping will be paid.
