Keysight U1610A User manual
Keysight U1610/20A
Handheld Digital
Oscilloscope
Quick Start
Guide
Contacting Keysight
www.keysight.com/find/assist
(worldwide contact information for
repair and service)
Safety and EMC Information
This handheld scope is certified to
the following safety and EMC
requirements.
– IEC 61010-1:2001/EN
61010-1:2001
– Canada: CAN/CSA-C22.2
No. 61010-1-04
– USA: ANSI/UL 61010-1:2004
– IEC 61326-1:2005/EN
61326-1:2006
– Australia/New Zealand: AS/NZS
CISPR 11:2004
– Canada: ICES/NMB-001:
ISSUE 4, June 2006
Use with compatible test probe/
leads.
Safety Notices
CAUTION
A CAUTION notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly
performed or adhered to, could
result in damage to the product or
loss of important data. Do not
proceed beyond a CAUTION notice
until the indicated conditions are
fully understood and met.
WARNING
A WARNING notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly
performed or adhered to, could
result in personal injury or
death. Do not proceed beyond a
WARNING notice until the
indicated conditions are fully
understood and met.
Safety symbols
Direct current (DC)
Alternating current (AC)
Both direct and alternating
current
Earth (ground) terminal
Caution, risk of danger
(refer to the instrument
manual for specific Warning
or Caution information)
Equipment protected
throughout by double
insulation or reinforced
insulation
Caution, risk of electric
shock
CAT II Category II overvoltage
protection
CAT III Category III overvoltage
protection
2 Keysight U1610/20A Quick Start Guide
For further safety information details, refer to the
Keysight U1610/20A Handheld Digital Oscilloscope User’s Guide.
Keysight U1610/20A Quick Start Guide 3
Table of Contents
Charge the Battery . . . . . . . . . . . . . . . . . . . . . . 6
Power On the Handheld Scope . . . . . . . . . . . . . 7
Product Outlook . . . . . . . . . . . . . . . . . . . . . . . . 8
Set the Date and Time . . . . . . . . . . . . . . . . . . 11
Set the Language . . . . . . . . . . . . . . . . . . . . . . 11
Reset the Oscilloscope . . . . . . . . . . . . . . . . . . 11
Data Logging . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Connect Probes to Oscilloscope Terminals . . 12
Connect Test Leads to Meter Terminals . . . . . 13
Meter Measurements . . . . . . . . . . . . . . . . . . . 14
Compensate the Scope Probe . . . . . . . . . . . . 15
Access the Quick Help . . . . . . . . . . . . . . . . . . 16
4 Keysight U1610/20A Quick Start Guide
THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK.
Keysight U1610/20A Quick Start Guide 5
Verify that you received the following items in the
shipment of your handheld scope:
✔1 x Power cable
✔1 x Li-Ion battery pack, 10.8 V (included in the
handheld scope)
✔1 x AC/DC adapter
✔2 x 10:1 CAT III 600 V scope probe
✔1 x BNC-to-probe adapter
✔1 x DMM (digital multimeter) test lead kit
✔1 x USB cable
✔
1 x Hand strap (attached on the handheld scope)
✔
1 x Neck strap
✔
Printed Quick Start Guide
✔
Certificate of Calibration
If anything is missing or damaged, contact the
nearest Keysight Sales Office.
NOTE
All related documents and software are available for
download at www.keysight.com/find/hhTechLib.
6 Keysight U1610/20A Quick Start Guide
Charge the Battery
Before using the handheld scope for the first time
or after a prolonged storage period, fully charge
the battery for at least 3 hours, with the handheld
scope turned off, using the AC/DC adapter
provided. If the battery is fully discharged after
subsequent use, charge the battery with the
handheld scope turned on.
The power key will turn constant yellow when
the battery is fully charged.
Keysight U1610/20A Quick Start Guide 7
Power On the Handheld Scope
Press and hold for approximately 3 seconds.
When the handheld scope display appears, the
handheld scope is ready for use.
NOTE
Hook up all cables and accessories before applying
power. You can connect/disconnect probes while
the handheld scope is turned on.
8 Keysight U1610/20A Quick Start Guide
Product Outlook
Scope terminals
Display screen
Function softkeys
To perform the
function displayed
above each softkey.
Acquisition and
function controls
To access the scope,
meter, logger,
system, and help
functions.
Vertical controls
To set the
vertical scaling
(volt/div) and
vertical offset.
Power key
USB interface
connectorand
DC power
inlet
Directional keys
Horizontal controls
To control the sweep speed
(sec/div) and horizontal position
of the waveform. Use
to zoom into the waveform.
Meter terminals
Keysight U1610/20A Quick Start Guide 9
Oscilloscope Display
Multimeter Display
6
4
1 5
7
8
3
2
6
4
10
9
11
12
13
10 Keysight U1610/20A Quick Start Guide
Logger Display
1
Displays the channel and timebase setup
information.
2
Displays the channel input waveforms.
3
Displays the sample rate.
4
Displays the key/softkey function menus.
5
Displays the signal acquisition mode.
6
Displays the battery status and AC
connectivity for battery charging.
7
Displays the signal triggering status.
8
Displays the date and time.
9
Displays the acquisition, start date and time,
and duration status.
10
Displays the measurement.
11
Displays the virtual measurement scale.
12
Displays the average, maximum, and
minimum values.
13
Indicates the auto or manual ranging mode.
14
Displays the logging graph.
6
9
10
14
4
12
Other manuals for U1610A
2
This manual suits for next models
1
Table of contents
Other Keysight Test Equipment manuals
Keysight
Keysight M8050A User manual
Keysight
Keysight TS-5020 User manual
Keysight
Keysight Infiniium 90000A Series User manual
Keysight
Keysight 85053A Manual
Keysight
Keysight InfiniiVision 4000G X Series User manual
Keysight
Keysight 90000 X Series User manual
Keysight
Keysight InfiniiVision 2000 X Series User manual
Keysight
Keysight 10070D User manual
Keysight
Keysight TS-5400 Operating instructions
Keysight
Keysight PXB MIMO Receiver Tester Owner's manual
Keysight
Keysight Infiniium MXR Series User manual
Keysight
Keysight N5242-60124 User manual
Keysight
Keysight Infiniium 8000 Series User manual
Keysight
Keysight M9380A User guide
Keysight
Keysight 4000 X-Series Setup guide
Keysight
Keysight 6 Series User manual
Keysight
Keysight Infiniium 9000 Series User manual
Keysight
Keysight TS-5020 Operating instructions
Keysight
Keysight U2701A User manual
Keysight
Keysight N2840A User manual
