Kero-Sun RS-220 User manual

RS – 220

GB OPERATING MANUAL ..............................PAGE 2

D GEBRAUCHSANWEISUNG............................PAGE 16

F MANUAL D’UTILISATION ............................PAGE 32

NL GEBRUIKSAANWIJZING .............................PAGE 48

E INSTRUCCIONES DE USO ............................PAGE 64

I ISTRUZIONI D’USO .................................PAGE 78

AFNOR CERTIFICATION - 11, RUE FRANCIS DE PRESSENSE

93571 LA PLAINE SAINT-DENIS CEDEX

FICHE INFORMATIVE

NF 128 45 / 01

La marque NF garantit

la qualité de cet article

suivant les normes françaises

et Règles de certification

de l’application NF 128

CONFORME A LA NORME NF D 35-300 ET AUX SPECIFICATIONS

COMPLEMENTAIRES DEFINIES PAR LES REGLES

DE CERTIFICATION DE LA MARQUE NF 128

PRINCIPALES CARACTERISTIQUES CERTIFIEES:

• Sécurité du dispositif d’allumage

• Débit calorifique

• Efficacité des dispositifs de sécurité

• Stabilité

• Contrôle de la teneur en NOx dans les produits de combustion

• Contrôle de la qualité de la combustion (absence de CO)

• Endurance

• Intermittence

CONSEILS D’UTILISATION ET D’ENTRETIEN

Se reporter à la notice jointe à l’appareil et à la plaque de sécurité sur

l’appareil

Référence et numéro de lot ou de série de l’article : se reporter au produit

Distributed in Europe by:

TOYOTOMI EUROPE SALES B.V.

Doornhoek 4025

5465 TD Veghel, The Netherlands

Email: [email protected] Website: www.toyotomi.eu

Si une difficulté subsistait, vous pouvez écrire à

EUROVENT CERTITA CERTIFICATION

Le Titien-48/50, rue de la Victoire

F-75009 PARIS

En cas d´insatisfaction, consultez d´abord votre revendeur :

Thank you for choosing a “TOYOTOMI” product!

Toyotomi products are used by satisfied customers worldwide. In order to

assure the comfortable and safe use of our products by customers in each

country, our products conform to the safety standards not only in Japan but

also in every country around the world we do business with.

Toyotomi tailors its products to satisfy its customer’s needs by always pursuing

our business philosophy, “sharing joys in daily living”. We will continue to

research, develop and manufacture products that match people’s lifestyle for

efficiency, safety and comfort.

We hope that you’ll enjoy your Toyotomi appliance for years to come!

We invite you to read this instruction manual first, to ensure the maximum

lifetime for this appliance.

Get to know us better…visit us at www.toyotomi.eu for our full line of

products.

1 Read the diRections foR Use fiRst.

2 in case of anY doUbt, contact YoUR dealeR.

3 befoRe YoU staRt Reading, consUlt the main components list on the last page.

geneRal diRections foR Use

Below you will find the main steps to be taken for

using your heater. For more details, please refer to

the MANUAL.

Remove all packaging materials (refer to Section A, Fig. A).

Fill the removable tank Iand wait 30 minutes before you

ignite the heater (refer to Section B, Fig. I).

Insert the batteries into the battery holder L

(refer to Section A, Fig. G).

Check whether the combustion chamber Dis fully upright

(refer to Section A, Fig. F).

Ignite the heater by turning the knurled wick adjustment

knob B as far to the right as possible and then gently push the

ignition button C (refer to Section C, Fig. K and L).

After igniting the heater it will take 10 to 15 minutes before you

can check if the heater burns well (refer to Section D).

Switch off the heater (refer to Section E).

•As a fire precaution, the tank must be filled either when the heater has been

switched off or in another room than the room where the heater is installed.

•Always ensure that the tank is closed properly after filling it at a safe distance from

all sources of heat and open flames (see Section B).

•Store all fuel containers with their original caps and seals in a cool and dark place.

•Fuel ages. Use new fuel at the start of every heating season.

•Only use high quality and water -free pure paraffin in accordance with local

legislation.

•Before changing brands and/or types of fuel make sure that the mobile heater first

completely empties all of the remaining fuel inside the heater.

•The first time you ignite your heater it will smell like ’new’ for a short time.

1 Read the diRections foR Use fiRst.

2 in case of anY doUbt, contact YoUR dealeR.

3 befoRe YoU staRt Reading, consUlt the main components list on the last page.

What YoU need to KnoW in adVance

ALWAYS MAKE SURE THAT THERE IS SUFFICIENT VENTILATION

Read this user manual carefully before using the appliance and keep it for future

reference. Install this device only when it complies with local/national legislation,

ordinances and standards. This product is intended to be used as a heater in

residential houses and is only suitable for use in dry locations, in normal household

conditions, indoors in living room, kitchen and garage.

This heater is equipped with an air quality control system . When there is

insufficient ventilation in the room or when the heater is being used in a room

which is too small, the heater will shut off automatically. For comfortable and safe

heating ensure that there is sufficient ventilation.

Note: To avoid unexpected shut off, we recommend to put a door or window ajar

when the heater is operating.

Regardless of the model, you must always make sure that the heater is used in

a room large enough to enable the heater to be used safely without extra

ventilation. If the room is smaller than required, you must always open a door or

window slightly (ensuring an opening of approx. 2.5 cm). It is important that every

room where the heater is used has sufficient air intake and efficient air outflow

(both openings must have a minimum cross section of 50 cm2). No modifications

to the safety system are allowed, as that will invalidate the guarantee that the air

probe will work properly. Consult your dealer in case of doubt.

Especially for France: Your heater was designed to operate exclusively on fuel for

liquid fuel-operated mobile heaters in accordance with the Decrees of 18-07-2002

and 25-06-2010. The use of other fuels is forbidden. Ask your dealer or check our

website for the addresses of our retailers. The liquid fuel-operated mobile heater

is intended as an extra heater, and not as a continuous source of heat.

Especially for United Kingdom: Only use Class C1 paraffin fuel in accordance with

BS2869; Part 2, or equivalent.

The user must comply with the following instructions for proper use:

DO NOT

- use the liquid fuel-operated mobile heater in caravans, boats, and vehicle

cabins;

- use the liquid fuel-operated mobile heater in insufficiently ventilated rooms

(consult the table of properties for the minimum dimensions of the room to be

heated), underground rooms and / or at a height of over 1500 metres;

- modify the heater safety features.

The use of this type of heating in public rooms is subject to prior regulatory

permission. Obtain proper information on this in advance.

THE RIGHT FUEL

Your heater has been designed for use with high-quality water-free pure paraffin

oil.. Only fuels of this kind will ensure clean and proper burning. Lower quality

fuel may result in:

increased possibility of malfunctioning

incomplete burning

reduced heater lifetime

smoke and/or smells

deposits on the grid or mantle

This transportation cap

is packed separately in

the box. Only this cap

ensures trouble-free

transportation of the

heater after use.

Store it well!

Only the use of the

correct fuel will ensure

safe, efficient, and

comfortable use of your

heater.

Using the right fuel is therefore essential for safe, efficient, and comfortable use

of your heater.

Damage and/or malfunctions of the heater due to the use of other than high

quality water-free pure paraffin oil is not covered by the warranty.

Always refer to your local dealer for the right fuel for your heater.

manUal

AINSTALLING THE HEATER

1Carefully remove your heater from the box and check the contents.

In addition to the heater you also need to have:

a transportation cap

these directions for use

Keep the box and the packaging materials (Fig. A) for storage and/or

transportation.

2Remove the other packaging materials:

Release the right side of the grill Gfrom the two slots by pulling the right

side of the grill to the left and then pull it forward (Fig. B).

Pull both ends of the packaging to the rear and at the same time slightly

downwards (see Fig. C).

Remove the combustion chamber Dfrom the heater and remove the pac-

kaging underneath (see Fig. D).

Put the combustion chamber back into its place. The combustion chamber

is positioned correctly when it can be smoothly moved a little to the left

and to the right by its handle E(Fig. E). Close the grill: Slightly lift it to

reposition it in its slot.

Open the lid of the removable tank Hand remove the piece of cardboard.

If the left side of the grill has been removed, first insert the flattened upper left

end of the grill into the upper left slot and then insert the other flattened end

into the lower left slot (Fig. F).

3Fill the removable tank as indicated in Section B.

4Insert the batteries into their holder Lat the back of the heater (Fig. G).

Ensure that the positive and negative poles match the + and - marks indicated

on the battery housing. It is best to use new alkaline batteries (4x D-size).

The floor should be firm and completely level.

Reposition the heater, when it is

not level. Do not correct the situation by placing books or other goods under the

heater.

6Your heater is now ready for use.

B FILLING FUEL

Fill the removable tank in a suitable place since there can always be some spillage.

Follow the procedure below:

1Make sure that the heater is switched off.

2Open the upper lid and lift the removable tank out of the heater (Fig. H).

Note: Some drops may leak from the tank. Put down the removable tank

(cap pointing upwards, handle on the floor) and screw off the fuel cap.

(Fig. I).

3Take the manual fuel pump and insert the smooth, most rigid tube into the

jerrycan. Make sure that it is in a higher position than the removable tank

(Fig. J). Insert the ribbed hose into the opening of the removable tank.

4Lock the valve on top of the pump (turn clockwise).

5Squeeze the pump a few times, until fuel starts flowing into the removable

tank. As soon as this happens, there is no need to press any longer.

6Check the fuel guage of removable tank while filling the tank (Fig. K). Stop

filling by loosening the valve on top of the pump (turn anti-clock-wise), once

the gauge indicates that the tank is full. Never overfill the tank, especially not

when the fuel is very cold (fuel expands when it heats up).

7Let the remaining fuel in the pump flow back into the jerrycan and carefully

remove the pump. Carefully screw the fuel cap back on the tank (Fig. L).

Clean off any spilled fuel.

8Check whether the fuel cap is straight and tightened properly. Reinstall the

removable tank in the heater (cap down). Close the lid.

Be sure to tighten the fuel tank cap and confirm that there is no leakage of the

fuel when the cap side is placed down. Then insert the removable fuel tank into

the heater.

CIGNITING THE HEATER

A new heater may give off some smells for a short while, when it is used for the

first time. You should therefore provide extra ventilation or ignite the heater

outside the living room.

When you use the heater for the first time, first put the filled removable tank into

place, and then wait approximately 30 minutes before you ignite the heater. This

allows the glass fibre wick to soak up the fuel. Follow the same procedure when

you have completely burnt up all fuel from the tank, and after the glass fibre wick

has been replaced.

empty full

Before igniting the heater, always check the fuel indicator to see whether the

removable tank needs filling up (Green=full, Red=empty).

Always ignite the heater with the ignition coil K. Never use matches or a cigarette

lighter.

Follow the procedure below:

1Turn the knurled wick adjustment knob clockwise to its stop (Fig. M). If you

apply more pressure you may turn it slightly further; however, it will

automatically return to the start position. When you have set the wick to its

highest position, this action will automatically activate the safety device.

2Push in the ignition button C(Fig. N), but do not apply too much force.

Release the ignition button as soon as a flame is visible in the combustion

chamber D.

When you have ignited the heater and it shuts off again shortly after, the batteries

need to be replaced. It is best to use new alkaline batteries (4x D-size).

If the heater has been used only a few times and the wick adjustment knob is not

locked, first turn the wick adjustment knob (Fig. O) completely left, before putting

the wick in the highest position for ignition (Section C).

After having ignited the heater, always check whether the combustion

chamber Dis level, by sliding it slightly to the left and the right by combustion

chamber handle (Fig. F). This should be a smooth movement. If the combustion

chamber is not level, this will cause smoke and soot to develop.

DBURNING OF THE HEATER

After you have ignited the heater, it will take 10 to 15 minutes before you can check

whether the heater is burning well. Too high a flame may cause smoke and soot,

whereas too low a flame causes smells. (Fig. U).

If the flame remains low after the adjustment, the wick height must be

adjusted (refer to Section G).

Burning that is too low may be caused by:

insufficient fuel (fill the tank)

poor fuel quality (contact your dealer)

insufficient ventilation (put window or door ajar)

wastage of the wick (contact your dealer or replace the wick, refer to section L)

✗

✓

✗ U

1-3 cm.

When there is insufficient ventilation in the room, the heater shuts off automatically.

After improving the ventilation of the room (e.g. by opening a door or window a

little more), the heater can be ignited again.

This heater is equipped with a safety mechanism which switches off the heater when

the removable fuel tank is taken out of its compartment (Fig. P). To re-ignite the

heater, place the removable fuel tank back in the heater and follow the instructions

as described in Section C.

ESWITCHING OFF THE HEATER

Push the OFF-button . The flame will extinguish after a little while (Fig. Q).

FMALFUNCTION, CAUSES AND SOLUTIONS

If any malfunctioning cannot be solved from the directions below, please contact

your dealer.

THE HEATER DOES NOT IGNITE

The batteries are not positioned correctly in the holder. Check (Fig. R).

There is not enough power left in the batteries for the ignition. Replace (Fig. R).

You have run out of fuel from the tank or the wick has been replaced.

After having refilled and replaced the removable tank, wait for 30 minutes

before igniting the heater.

You are pushing the ignition button Cwith too much force.

Push it in less forcefully (Section C).

The ignition coil K is defective.

Contact your dealer.

IRREGULAR FLAME AND/OR SOOT AND/OR SMELLS

The combustion chamber ❹has not been positioned correctly.

Use the combustion chamber handle to put it level, until you can easily slide it

slightly to the left and to the right and the chamber is level.

You are using fuel which is past its ‘use by’ date.

Start every heating season with fresh fuel.

You are using the incorrect type of fuel.

Refer to THE RIGHT FUEL (See Section ’What you need to know in advance’).

Dust has gathered in the lower part of the heater.

Contact your dealer.

The wick height is not correct.

Contact your dealer.

THE HEATER SLOWLY EXTINGUISHES

The removable tank is empty.

See Section B.

The lower reservoir is contaminated by water.

Contact your dealer.

The wick has hardened on the upper side.

Burn the heater until all fuel is used (Section G). Use the right fuel.

You are using fuel which is past its ‘use by’ date.

Start every heating season with fresh fuel.

THE HEATER REMAINS BURNING LOW

Wick position too low.

Contact your dealer.

Before you refilled the tank, the heater had burnt up almost all the fuel.

After having refilled and replaced the removable tank, wait for 30 minutes

before igniting the heater.

You are using the incorrect type of fuel.

Refer to THE RIGHT FUEL (See Section ’What you need to know in advance’).

The room is insufficiently ventilated.

Leave a window or a door wide open for a while.

THE HEATER IS BURNING TOO HIGH

You are using an incorrect, too volatile type of fuel.

Refer to THE RIGHT FUEL (See Section ’What you need to know in advance’).

Wick position too high.

Contact your dealer.

GMAINTENANCE

Your heater needs hardly any maintenance. It is, however, important that you

remove dust and stains in time with a damp cloth, because otherwise these

may cause stains that are hard to remove. Under normal conditions, only two

components are subject to wear:

1. THE BATTERIES

You may replace the batteries yourself. Do not dispose of old batteries along with

the other domestic waste. Follow the locally applicable regulations regarding the

disposal of domestic chemical waste.

2. THE WICK

To extend the glass fibre wick life, you must occasionally let the heater burn until

the tank is completely emptied and the heater extinguishes by itself. Do this when

you notice that the flame is weakening. The burn-out will cause some smells, so it

is recommended that you take the heater outside of the living room.

3. THE IGNITION COIL

The ignition coil will have a longer life, if you ignite the heater in the correct

manner. Replace the batteries in time and take care not to push in the ignition

button with too much force. If the filament is broken, the ignition coil must be

replaced.

Do not remove any heater components yourself. Always contact your dealer for

repairs.

Let the heater cool down first, before you start any maintenance or service work.

HSTORAGE (END OF THE HEATING SEASON)

We recommend that you burn up all the fuel in the fuel tank at the end of the

heating season and store the heater properly. Follow the procedure on the next

page:

1Ignite the heater outside the living room and let it burn until all fuel is used.

2Let the heater cool down.

3Clean the heater with a damp cloth and then dry it with a dry cloth.

4Remove the batteries from the holder Land store them in a dry place.

5Store the heater in a dust-free place, if possible in its original packaging.

Unused fuel cannot be used for the next heating season. If there is still some

fuel left, do not throw it away, but dispose of it in accordance with the local

regulations for the disposal of domestic chemical waste. Always start the new

heating season with fresh fuel. When you start re-using the heater, follow the

instructions again (starting from Section A and as specified).

broken ignition coil

Table of contents

Other Kero-Sun Heater manuals

Kero-Sun

Kero-Sun KTMC-15 User manual

Kero-Sun

Kero-Sun CH-900 User manual

Kero-Sun

Kero-Sun KHFN-2021 User manual

Kero-Sun

Kero-Sun KCF-70 User manual

Kero-Sun

Kero-Sun Moonlighter User manual

Kero-Sun

Kero-Sun LME-900M User manual

Kero-Sun

Kero-Sun OMNI 230GEF User manual

Kero-Sun

Kero-Sun LC-45 User manual

Kero-Sun

Kero-Sun KPT/R 2000 User manual

Kero-Sun

Kero-Sun KBH-30 User manual

Kero-Sun

Kero-Sun TKRMC-15 User manual

Kero-Sun

Kero-Sun Radiant Fan 111 User manual

Kero-Sun

Kero-Sun DC-90 Manual

Kero-Sun

Kero-Sun LC-43 User manual

Kero-Sun

Kero-Sun KRMC-15 User manual

Kero-Sun

Kero-Sun Moonlighter H User manual

Kero-Sun

Kero-Sun LC-300 User manual

Kero-Sun

Kero-Sun KON-09 User manual

Kero-Sun

Kero-Sun LC-43G User manual

Kero-Sun

Kero-Sun Omni 105 Type M User manual

Kero-Sun

Kero-Sun Omni 105 Type J User manual

Kero-Sun

Kero-Sun Sunsprite User manual

Kero-Sun

Kero-Sun Omni 105 Type L User manual

Kero-Sun

Kero-Sun KSC-960A User manual

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide