Kendal Lighting Virtua User manual

(MODEL NUMBER:AC-22752)

1. Securely attach the hanger bracket to the outlet box

by washers and screws suppplied. Connect white

wire from ceiling to white wire from receiver with

wire nut. Connect black wire from ceiling to

black wire from receiver with wire nut. (see Fig.4)

2. Carefully lift the fan and seat the down rod ball

assembly on the hanger bracket. Be sure the

groove in the ball is lined up with tab on the

hanger bracket . Do not pinch wires between the

ball and down rod assembly and hanger bracket

(see Fig.5)

3. Install the safety cable into the building structure.

(see Fig.6)

Putting Your Fan Together

Hanging Your Ceiling Fan

1. Remove the hairpin clip & washer from the clevis

pin and remove clevis pin from down rod. (see

Fig.1)

2. Insert the down rod through the center opening in

the canopy,coupling cover and route the motor

leads through the hanger ball/downrod assembly.

Align the clevis pin holes in the downrod with the

holes in the motor coupling. The clevis pin must

pass through the holes in the motor coupling and

the downrod. Place the washer onto the clevis pin

and install the hairpin clip making sure to push

straight leg of the hairpin clip through the hole

near hanger ball to make sure the clevis pin is

properly installed(see Fig.2)

3. Reinstall the 2 set screws in the motor coupling and

securely tighten set screws against the down rod

assembly.

Attached each blade assembly to the blade bracket

using the blade screws and blade washers.Tighten

them securely.(see Fig.3)

Caution: To reduce the risk of personal injury.

Do not bend the blade when installing, balancing

or cleaning the fan. Do not insert foreign objects

between rotating fan blades.

DOWNROD

ASSEMBLY

WASHER

CLEVIS PIN

HAIR PIN CLIP

DOWNROD ASSEMBLY

CANOPY HOLE COVER

COUPLING COVER

WASHER

SCREW

FAN BODY

CLEVIS PIN

HAIR PIN CLIP

MOTOR COUPLING

CANOPY

SCREW

WASHER

BLADE

BLADE BRACKET

OUTLET BOX

HANGER BRACKET

FLAT WASHER

STAR WASHER

SPRING WASHER

SCREW

WHITE WIRE

BLACK

WIRE

WHITE WIRE

RECEIVER

BLACK

WIRE

HANGER BRACKET

DOWNROD

CEILING

SATETY CABLE

WASHER

SCREW

DOWNROD

HANGER BRACKET

Wiring Your Ceiling Fan

Caution: To avoid possible electrical shock,

be sure electricity is turned off at the main

fuse box before wiring.

1. If you are not sure that the electrical box is

grounded,contact a licensed electrician for

advice.It must be grounded for safe operation.

2. Connect the red wire from receiver to the

red wire from fan with wire nut .Connect

the purple wire from receiver to the purple

wire from fan with wire nut.Connect the

blue wire from receiver to the blue wire

from fan with wire nut. Connect the grey

wire from receiver to the grey wire from

fan with wire nut. Connect the white wire

from receiver to the white wire from fan

with wire nut.Connect the green wire from

ceiling,and green wire from hanger bracket

with green wire from downrod ball with

wire nut.(see Fig.7)

3.Remove one of screws and loosen the other

screw from the hanger bracket. (see Fig.8)

4. Mount the canopy on the hanger bracket

and tighten the screws.(see Fig.9)

5. Place the canopy hole cover over the screws

and twist the cover to tighten. (see Fig.10)

GREEN WIRE

OUTLET BOX

RECEIVER

BLUE WIRE

WHITE WIRE

GREY WIRE

RED WIRE

PURPLE WIRE

FAN

HANGER

BRACKET

SCREW

HANGER

BRACKET

CANOPY

SCREW

CANOPY

CANPOY HOLE

COVER

SCREW

LIGHT KIT ADAPTER

FAN

1. Remove 1 of 3 screws on light kit adapter,and

loosen the other 2 screws. (See Fig.11)

2.Gently pull the wire through light kit plate.Have

the key hole over the loosened the screws.Turn

the light kit plate until it get the end of narrow

end. Then, tighten the previously removed and

loosened screws.(see Fig.12 & 13)

3.Remove 3 screws on light kit plate.(see Fig.14)

4.Plug together light kit wires from fan to light kit

wires from LED light(see Fig.15)

5.Tighten the light kit by using the 3 screws

removed in step 3 (see Fig.16)

6. Attach the PC shade by locating tabs in light

kit with grooves on the light shade and twist

clockwise until tight (see Fig.17)

Installing The Light Kit

SCREW

LIGHT KIT PLATE

LIGHT KIT

ADAPTER

FAN

SCREW

LIGHT KIT

PLATE

LIGHT KIT PLATE

LED LIGHT

PLUG

LIGHT KIT PLATE

SCREW

TAB

LIGHT KIT PLATE

INDENTATION

PC SHADE

TNA18010305

REMOTE CONTROL SETTING AND OPERATION

UNIVERSAL MODE AND LEARNING MODE

There is a “Universal Mode” and “Learning Mode” with the remote control.

When selecting “Universal Mode”, simply place dip (code) switch at UPPER

position(COMMON CODE). Your fan remote control is ready to use.

Note: If using universal mode, your fan can be controlled with other remote

transmitters with the same setting.

To control the fan with speciﬁc remote transmitter, choose “ Learning Mode ”

by placing the dip (code) switch at LOWER position(L.CODE) and then select

function setting as below.

Learn function setting: Restore power source to your fan, press and hold

the “ LEARN ” button for at least 3 seconds. You must press the “LEARN ”

button within 60 seconds of restoring power to the fan.

Note: Power must be off for a minimum 10 seconds, then turn the power

back on for remote control learn function setting.

Note: If the fan is installed with light, light will blink 2 times. The remote

control setting process is complete and your fan is ready for use. For fans

without light, check operation using remote transmitter.

Note: To control multiple fans, ensure the settings are set at the same setting.

A fan can be controlled by 2 transmitters maximum.

TRANSMITTER OPERATION

Remove the battery cover from the remote control transmitter and install batteries,

Replace the cover.

Note : Use 2 1.5V/AAA batteries (included).

Note : If not using for long period of time, remove battery to prevent damage

to remote transmitter, and store the remote transmitter away from excess

heat or humidity.

DIM

LEARN

L.CODE

COMMON

CODE

L.CODE

COMMON

CODE

DIM

Universal Mode

Learning Mode

DIMMING / NON DIMMING SETTING

The “DIM” selection is the light dimmable selection , the light will cycle

from bright to dim to bright until button is released. The “ON” selection is the

light ON/OFF only (non dimming function).Light will maintain last setting if

turned off.

Note: The remote control is pre-set with dimming function at factory,

Note: Ensure electricity is turned off before installing the receiver (Refer

to the ceiling fan instructions)

Dimming/

Non dimming

LEARN

Learn

RECEIVER PROTECTIVE FUNCTIONS

Lock protection- The DC motor has a built-in safety feature against blade or motor obstruction during operation. should

something obstruct the fan blades or motor, the motor will keep trying to run for 5 times and then stop operation

after about 60 seconds of interruption. Please remove obstacles and reset. To reset, turn the fan off with remote

transmitter and then turn the fan on. Or, you may turn the power off for 15 seconds. Then turn the power back on, and

then turn the fan on.

Over load protection (current limit)- The device limits the maximum current output from the receiver/drive when the fan

or light load is increased abnormally. The fan will shut off if over lamped.

TN15122801

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS

SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1)THIS DEVICE MAY NOT

CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY

INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE

UNDESIRED OPERATION.

Remote Control Fan Speed And Light Functions.

Fan speed

1 = minimum speed 2 = low speed

3 = medium low speed 4 = medium speed

5 = medium high speed 6 = high speed

This button turns the fan off.

Forward/ Reverse button- This button controls the direction of the fan rotation

Press once to change direction of the fan rotation. Fan must be running to reverse.

Light button-Press this button to turn light on or off. To dim light (

Setting at “DIM”

position

), hold down the button, the light will cycle from bright to dim to bright until button

is released.

Note

: This remote control has an auto resume function, the fan and light will maintain the

last setting if power is turned off.

NOTE:

1. When powering on after installation, the fan may start automatically due to factory preset settings.

2. If fan or light isn’t working, reset power ( turn the power off for at least 10 seconds and then turn the power back on

)

and redo the learn function setting.

3. If there are multiple fans in the same room, when setting, please make sure the power supply for the setting fan is

independant of the other fans.

4. When turning the fan on or operating the forward/reverse function, it is normal for the fan to rotate and run on both

directions, for approximately 1 minute and then stop.

TN15122801

Install Transmitter wall mount cradle with 2 screws provided.

WALL MOUNT CRADLE INSTALLATION

(Note: It can take a few seconds to change direction once button has been pushed.)

This manual suits for next models

Table of contents

Other Kendal Lighting Fan manuals

Kendal Lighting

Kendal Lighting AC-21454 User manual

Kendal Lighting

Kendal Lighting AC-12452 User manual

Kendal Lighting

Kendal Lighting AC6842B User manual

Kendal Lighting

Kendal Lighting AC-22160 User manual

Kendal Lighting

Kendal Lighting AC-24344 User manual

Kendal Lighting

Kendal Lighting AC-23856 User manual

Kendal Lighting

Kendal Lighting AC-19752 User manual

Kendal Lighting

Kendal Lighting AC-21750 User manual

Kendal Lighting

Kendal Lighting AC-30052 User manual

Kendal Lighting

Kendal Lighting AC-30152 User manual

Kendal Lighting

Kendal Lighting Triax AC-22352 User manual

Kendal Lighting

Kendal Lighting AC-20070 User manual

Kendal Lighting

Kendal Lighting AC-24144 User manual

Kendal Lighting

Kendal Lighting AC-16652 User manual

Kendal Lighting

Kendal Lighting AC-20644 User manual

Kendal Lighting

Kendal Lighting AC-30252 User manual

Kendal Lighting

Kendal Lighting AC-30952 User manual

Kendal Lighting

Kendal Lighting AC-30552 User manual

Kendal Lighting

Kendal Lighting AC-21852 User manual

Kendal Lighting

Kendal Lighting AC-22452 User manual

Kendal Lighting

Kendal Lighting AC-22054 User manual

Kendal Lighting

Kendal Lighting AC-21560 User manual

Kendal Lighting

Kendal Lighting AC-19544 User manual

Kendal Lighting

Kendal Lighting AC-20152 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual