Ken A Vision TRIG X-1000-1 User manual

Microprojector

Instruction Manual

X-1000-1

TRIG

Table of Contents

Using the Microprojector 4

Setting up Microprojector 4

Revolving the Dustproof Disk 4

Table Projection 6

Screen Projection - Direct Projection 7

Horizontal Projection - Using the mirror 8

To Polarize Light - Using the Microprojector as a

polarizing microscope

Using the Microprojector

General Notes:

Your Microprojector is a very stable technology that has been available for

many years but still incorporates many advances in the microprojection field.

Uniquely, it will project an image either vertically or horizontally. For small

groups or an individual, it is best to project vertically. When using the Micro-

projector with a large group or entire class, project from the horizontal posi-

tion. For showing wet demonstrations, use the unit in the vertical position, and

then use the mirror to reflect the image onto a screen for whole class viewing.

Use your Microprojector whenever possible, as it allows everyone to see the

same image simultaneously, making it ideal for study, discussion and lectures.

Setting up Microprojector:

1. Make sure all electrical cords, plugs are in good shape with no fraying

and loose prongs

2. Suggestion - Wrap cord around table leg a few times. If a student

accidentally pulls on cord, then the Microprojector will not be pulled off

the table.

3. Plug Microprojector into proper electrical outlet.

4. Turn on Switch in base of Microprojector unit.

Revolving the Dustproof Disk:

The Revolving Dustproof Disk (5) is located under the nosepiece of the

objective, and has four options for the microprojector. These must "click" into

place at the red line (7) (left side as you face the front of the Microprojector)

on the metal base of the revolving nosepiece.

C Clear View (no additional lens in light pathway)

E Eyepiece 10x

P Polarizer (used in conjunction with Revolving Polarizing

Analyzer)

A Auxiliary 5X lens

Figure 1

Figure 2

Figure 3. Labeled diagram of Microprojector.

Table Projection:

1. Turn the switch to the "ON" position.

2. Place a white sheet of paper between the legs of the base, or focus on a

white or light colored surface.

3. Be sure the mirror is out of the way of the light beam coming straight

through the stage and going to the table surface.

4. Be sure that the Revolving Polarizing Analyzer (7) is out of the light path.

5. Rotate the Revolving Dustproof Disk (5) until the RED "C" on the left side

of the disk is directly under the RED line (7) on the upper disk. Feel the

Revolving Disk (5) "click" into position.

6. Place the specimen slide on the stage and hold in place with the stage

clips (3).

7. Focusing - Use the knurled focusing knob (6), located under the stage (3),

at the back of the unit behind the 16mm objective to focus image onto

1. Light Source 5. Revolving Dustproof Disc

2. Revolving Polarizer Analyzer 6. Knurled Focusing Knob

3. Stage with Stage Clips 7. Red Line

4. 16mm Objective Lens 8. Mirror

the desktop. First lower the stage to the lowest position, and then reverse

direction until the specimen is brought into focus.

8. To gain an additional 5X magnification, rotate the Revolving Dustproof

Disk (5) until the RED "A" is under the red line (7) on the upper disk.

Again feel the Revolving Disk "click" into position.

9. The Microprojector may be used in a lighted room or in a darkened

room, depending on the nature of the specimen being looked at or the

experiment being done.

Screen Projection- Direct Projection

Figure 2. Position of Head for Screen Projection

1. Turn the switch to the "ON" position. Room may need to be darker for

horizontal projection then for vertical projection.

2. Carefully rotate the entire head of the unit into a horizontal position. Do

this by placing one hand on the base, just below the hinge joint to

stabilize the base. Then position the head assembly with your other hand

by pushing gently on THE BACK of two metal bars which support the

stage and lens assembly. DO NOT FORCE anything, as it should move

smoothly.

3. Be sure the mirror (8) is out of the way of the light beam coming straight

through the stage and going to screen or wall on which you wish to

project the image.

4. Be sure that the Revolving Polarizing Analyzer (2) is out of the light path.

5. Rotate the Revolving Dustproof Disk (5) until the RED "C" on the left side

of the disk is directly under the RED line (7) on the upper disk. Feel the

Revolving Disk "click" into position.

6. Place the specimen slide on the stage and hold in place with the stage

clips (3).

7. Focusing - Use the knurled focusing knob (6), located under the stage, at

the back of the unit behind the 16mm objective to focus image onto the

desktop. First lower (move away from light source) the stage to the

lowest position, and then reverse direction until the specimen is brought

into focus.

8. To gain an additional 5X magnification, rotate the Revolving Dustproof

Disk (5)until the RED "A" is under the red line (7) on the upper disk.

Again feel the Revolving Disk "click" into position.

9. In general, the higher the magnification, the darker the room needs to

be. NOTE: sometimes it is easier to set up for Vertical projection first and

then tip the assembly up for Horizontal projection

Horizontal Projection- Using the mirror

Figure 1. Position for Horizontal Projection

1. The most common reason for using the Microprojector in this position is

for "wet" specimen's such as depression slides with pond water, or any

specimen where water, oil, etc. would flow off the slide because unit is in

the Horizontal position.

2. Turn the switch to the "ON" position.

3. Be sure that the Revolving Polarizing Analyzer (2) is out of the light path.

4. Rotate the mirror (8) into position so that it intersects with the light beam

coming through the stage. The light should now be reflected onto the

screen or wall on to which you intend to project.

5. Rotate the Revolving Dustproof Disk (5) until the RED "C" on the left side

of the disk is directly under the RED line (7) on the upper disk. Feel the

Revolving Disk "click" into position.

6. Place the specimen slide on the stage and hold in place with the stage

clips (3).

7. Focusing - Use the knurled focusing knob (6), located under the stage, at

the back of the unit behind the 16mm objective to focus image onto the

desktop. First lower the stage to the lowest position, and then reverse

direction until the specimen is brought into focus.

8. To gain an additional 5X magnification, rotate the Revolving Dustproof

Disk (5) until the RED "A" is under the red line (7) on the upper disk.

Again feel the Revolving Disk "click" into position.

9. In general, the room needs to be darker when using the mirror to project

the image.

To Polarize Light - Using the Microprojector as a polarizing

microscope:

Figure 3.

1. Set up the microprojector in either the vertical or horizontal position as

noted above.

2. Move the Revolving Polarizing Analyzer (2) so that the polarized lens

(dark tinted) into the light path (located just below the light source).

3. Turn the Revolving Dustproof Disc (5) until the P (Polarizer) clicks into

place. This places the lower or second polarized lens in place.

4. Use the focusing knob (6) to focus image onto desk top.

5. Rotate the Analyzer lens located within the ring of the Revolving Polarizing

Analyzer (2) to change orientation of the polarized light. (Remember to

achieve polarization of light two polarizing lenses in the same optical

plane must rotate so that the lines of the lenses alternately move between

being parallel to each and perpendicular to each other).

Using Microprojector as a standard microscope -

1. Turn the switch to the "ON" position.

2. Carefully rotate the entire head of the unit into a horizontal position. Do

this by placing one hand on the base, just below the hinge joint to

stabilize the base. Then position the head assembly with your other hand

by pushing gently on THE BACK of two metal bars which support the

stage and lens assembly. DO NOT FORCE anything, as it should move

smoothly

3. Rotate the Polarizer analyzer (2) so that the opaque (not the polarizing

lens) is in the light path from the light source.

4. Rotate the Revolving Dustproof Disk (5) until the RED "E" on the left side

of the disk is directly under the RED line (7) on the upper disk. Feel the

Revolving Disk "click" into position.

5. Place the specimen slide on the stage and hold in place with the stage

clips (3).

6. With the assembly in the horizontal position, now look through the

eyepiece back towards the light assembly.

7. Using the knurled focusing knob (6), lower the stage to the

lowest position, and then reverse direction until the specimen is brought

into focus

8. This will be the image normally seen in a standard microscope.

This manual suits for next models

Table of contents

Other Ken A Vision Microscope manuals

Ken A Vision

Ken A Vision Professor Stereo ESH200 User manual

Ken A Vision

Ken A Vision Video Flex® except 2000 series User manual

Ken A Vision

Ken A Vision Vision Scope 2 T-22XXX Series User manual

Ken A Vision

Ken A Vision T-1955 User manual

Ken A Vision

Ken A Vision Research Scope T-29041 User manual

Ken A Vision

Ken A Vision T-1922C User manual

Ken A Vision

Ken A Vision T-1953B User manual

Ken A Vision

Ken A Vision CoreScope T-1701C User manual

Ken A Vision

Ken A Vision Comparison Scope T-1924C User manual

Ken A Vision

Ken A Vision PrepScope 2 T-12011C User manual

Ken A Vision

Ken A Vision Digital CoreScope 2 T-17541C User manual

Ken A Vision

Ken A Vision T-1951 User manual

Ken A Vision

Ken A Vision Professor Stereo ESH200 User manual

Ken A Vision

Ken A Vision T-3300 User manual

Ken A Vision

Ken A Vision Comprehensive T-1901C User manual

Ken A Vision

Ken A Vision CoreScope T-1701C User manual

Ken A Vision

Ken A Vision Comprehensive T-1901C User manual

Ken A Vision

Ken A Vision Microprojector 2 User manual

Ken A Vision

Ken A Vision T-2701 User manual

Ken A Vision

Ken A Vision PupilCAM 1402KEM User manual

Ken A Vision

Ken A Vision Comprehensive Scope T-1901 User manual

Ken A Vision

Ken A Vision T-19541C User manual

Ken A Vision

Ken A Vision T-3300 User manual

Ken A Vision

Ken A Vision Digital Comprehensive Scope 2 User manual

Popular Microscope manuals by other brands

Thermo Scientific

Thermo Scientific Nicolet iN10 Using

National

National DC3-163 instructions

KERN Optics

KERN Optics OPE-1 User instructions

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Operation manual

Prior

Prior Lux POL operating instructions

Opitec

Opitec Smartscoop 115615 instructions

KERN

KERN OPO-1 operating instructions

Topcon

Topcon SP-1P user manual

Motic

Motic PA43 Operation manual

Leica

Leica DVM5000 Setup manual

MshOt

MshOt MZ62 user manual

KERN Optics

KERN Optics OZR-5 User instructions

VWR

VWR VisiScope 384 Series instruction manual

Nikon

Nikon ECLIPSE E200 POL instructions

Leica

Leica DI C800 User's manual & installation instructions

ThermoFisher Scientific

ThermoFisher Scientific Continuµm manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm manual

Olympus

Olympus SZ61 instructions