Keithley 2010 User manual

Model 2010 Multimeter

Quick Reference Guide

A GREATER MEASURE OF CONFIDENCE

2010-903-01B Page 6 Tuesday, February 13, 2001 10:56 AM

Model 2010 Multimeter

Quick Reference Guide



1996, Keithley Instruments, Inc.

Cleveland, Ohio, U.S.A.

Second Printing, February 2001

Document Number: 2010-903-01 Rev. B

Manual Print History

The print history shown below lists the printing dates of

all Revisions and Addenda created for this manual. The

Revision Level letter increases alphabetically as the manual

undergoes subsequent updates. Addenda, which are

released between Revisions, contain important change

information that the user should incorporate immediately

into the manual. Addenda are numbered sequentially.

When a new Revision is created, all Addenda associated

with the previous Revision of the manual are incorporated

into the new Revision of the manual. Each new Revision

includes a revised copy of this print history page.

Revision A (Document No. 2010-903-01) October 1996

Revision B (Document No. 2010-903-01) February 2001

All Keithley product names are trademarks or registered trademarks of

Keithley Instruments, Inc.

Other brand names are trademarks or registered trademarks of their

respective holders.

Table of Contents

Safety Precautions ...................................................... 1

Introduction ............................................................... 5

Front Panel Operation Summary ................................ 7

Remote Operation Summary .................................... 25

2010-903-01B Page 6 Tuesday, February 13, 2001 10:56 AM

Safety Precautions

The following safety precautions should be observed

before using this product and any associated instrumenta-

tion. Although some instruments and accessories would

normally be used with non-hazardous voltages, there are

situations where hazardous conditions may be present.

This product is intended for use by qualiﬁed personnel

who recognize shock hazards and are familiar with the

safety precautions required to avoid possible injury. Read

the operating information carefully before using the

product.

The types of product users are:

Responsible body

is the individual or group responsible for

the use and maintenance of equipment, for ensuring that

the equipment is operated within its speciﬁcations and

operating limits, and for ensuring that operators are ade-

quately trained.

Operators

use the product for its intended function. They

must be trained in electrical safety procedures and proper

use of the instrument. They must be protected from electric

shock and contact with hazardous live circuits.

Maintenance personnel

perform routine procedures on the

product to keep it operating, for example, setting the line

voltage or replacing consumable materials. Maintenance

procedures are described in the manual. The procedures

explicitly state if the operator may perform them. Other-

wise, they should be performed only by service personnel.

Service personnel

are trained to work on live circuits, and

perform safe installations and repairs of products. Only

properly trained service personnel may perform installation

and service procedures.

Exercise extreme caution when a shock hazard is present.

Lethal voltage may be present on cable connector jacks or

test ﬁxtures. The American National Standards Institute

(ANSI) states that a shock hazard exists when voltage levels

greater than 30V RMS, 42.4V peak, or 60VDC are present.

A good safety practice is to expect that hazardous voltage

is present in any unknown circuit before measuring.

Users of this product must be protected from electric shock

at all times. The responsible body must ensure that users

are prevented access and/or insulated from every connec-

tion point. In some cases, connections must be exposed to

potential human contact. Product users in these circum-

stances must be trained to protect themselves from the risk

of electric shock. If the circuit is capable of operating at or

above 1000 volts,

no conductive part of the circuit may be

exposed.

As described in the International Electrotechnical Commis-

sion (IEC) Standard IEC 664, digital multimeter measuring

circuits (e.g., Keithley Models 175A, 199, 2000, 2001,

2002, and 2010) are Installation Category II. All other

instruments’ signal terminals are Installation Category I and

must not be connected to mains.

Do not connect switching cards directly to unlimited

power circuits. They are intended to be used with imped-

ance limited sources. NEVER connect switching cards

directly to AC mains. When connecting sources to switch-

ing cards, install protective devices to limit fault current

and voltage to the card.

Before operating an instrument, make sure the line cord is

connected to a properly grounded power receptacle.

Inspect the connecting cables, test leads, and jumpers for

possible wear, cracks, or breaks before each use.

For maximum safety, do not touch the product, test cables,

or any other instruments while power is applied to the cir-

cuit under test. ALWAYS remove power from the entire test

system and discharge any capacitors before: connecting or

disconnecting cables or jumpers, installing or removing

switching cards, or making internal changes, such as

installing or removing jumpers.

Do not touch any object that could provide a current path

to the common side of the circuit under test or power line

(earth) ground. Always make measurements with dry hands

while standing on a dry, insulated surface capable of with-

standing the voltage being measured.

The instrument and accessories must be used in accor-

dance with its speciﬁcations and operating instructions or

the safety of the equipment may be impaired.

Do not exceed the maximum signal levels of the instru-

ments and accessories, as deﬁned in the speciﬁcations and

operating information, and as shown on the instrument or

test ﬁxture panels, or switching card.

When fuses are used in a product, replace with same type

and rating for continued protection against ﬁre hazard.

Chassis connections must only be used as shield connec-

tions for measuring circuits, NOT as safety earth ground

connections.

If you are using a test ﬁxture, keep the lid closed while

power is applied to the device under test. Safe operation

requires the use of a lid interlock.

If a screw is present, connect it to safety earth ground

using the wire recommended in the user documentation.

The symbol on an instrument indicates that the user

should refer to the operating instructions located in the

manual.

The symbol on an instrument shows that it can source

or measure 1000 volts or more, including the combined

effect of normal and common mode voltages. Use standard

safety precautions to avoid personal contact with these

voltages.

The

WARNING

heading in a manual explains dangers that

might result in personal injury or death. Always read the

associated information very carefully before performing the

indicated procedure.

The

CAUTION

heading in a manual explains hazards that

could damage the instrument. Such damage may invalidate

the warranty.

Instrumentation and accessories shall not be connected to

humans.

Before performing any maintenance, disconnect the line

cord and all test cables.

To maintain protection from electric shock and ﬁre,

replacement components in mains circuits, including the

power transformer, test leads, and input jacks, must be pur-

chased from Keithley Instruments. Standard fuses, with

applicable national safety approvals, may be used if the rat-

ing and type are the same. Other components that are not

safety related may be purchased from other suppliers as

long as they are equivalent to the original component.

(Note that selected parts should be purchased only through

Keithley Instruments to maintain accuracy and functional-

ity of the product.) If you are unsure about the applicability

of a replacement component, call a Keithley Instruments

ofﬁce for information.

To clean an instrument, use a damp cloth or mild, water

based cleaner. Clean the exterior of the instrument only.

Do not apply cleaner directly to the instrument or allow

liquids to enter or spill on the instrument. Products that

consist of a circuit board with no case or chassis (e.g., data

acquisition board for installation into a computer) should

never require cleaning if handled according to instructions.

If the board becomes contaminated and operation is

affected, the board should be returned to the factory for

proper cleaning/servicing.

10/99

Other manuals for 2010

Table of contents

Other Keithley Multimeter manuals

Keithley

Keithley DMM6500 User manual

Keithley

Keithley 2001 Use and care manual

Keithley

Keithley 2000 Use and care manual

Keithley

Keithley 2016 User manual

Keithley

Keithley 2110 User manual

Keithley

Keithley 164 User manual

Keithley

Keithley 2000 User manual

Keithley

Keithley 2700 User manual

Keithley

Keithley 2701 User manual

Keithley

Keithley 2110 User manual

Keithley

Keithley 2110-100 Use and care manual

Keithley

Keithley DMM6500 User manual

Keithley

Keithley 175 User manual

Keithley

Keithley 2001-TCSCAN User manual

Keithley

Keithley 195 User manual

Keithley

Keithley 2002 User manual

Keithley

Keithley 169 User manual

Keithley

Keithley 2010 User manual

Keithley

Keithley 172A User manual

Keithley

Keithley DMM7512 Owner's manual

Keithley

Keithley DMM7510 Use and care manual

Keithley

Keithley 197 User manual

Keithley

Keithley 165 User manual

Keithley

Keithley 2001 User manual

Popular Multimeter manuals by other brands

Agilent Technologies

Agilent Technologies 34420A user guide

Fluke

Fluke 83 user manual

Hameg

Hameg HM 8012 manual

Mastech

Mastech MY70 Operation manual

Steren

Steren MUL-300 user manual

Somogyi Elektronic

Somogyi Elektronic home SMA 92 instruction manual

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 operating instructions

PeakTech

PeakTech 4000 Procedure of calibration

YOKOGAWA

YOKOGAWA 90050B user manual

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 operating instructions

Fluke

Fluke 8846A Programmer's manual

Tempo Communications

Tempo Communications MM200 instruction manual

Elenco Electronics

Elenco Electronics CM-1555 operating instructions

Mastech

Mastech MS8238C user manual

SDAR

SDAR 830A, 830B, 830D, 830C user manual

RS PRO

RS PRO RS-9519BT instruction manual

BGS technic

BGS technic 8890 instruction manual

Amprobe

Amprobe Hexagon 60 user manual