KaiDeng K70 Sky Warrior User manual
2.4 GHZ 6 AXIS R/C QUADCOPTER
1.Four-Rotor design allows great speed and maneuverability for indoor
and outdoor use.
2.Built-in 6-axis Gyro ensures excellent stability.
3.loading capacity up to 500g.
4.Auto hover/Headless function/One key to return.
5.360-degree 3-dimensional stunt and tumbling function.
6.WIFI Photo/Video.
7. 2MP camera Photo/Video.
8. 5MP camera Photo/Video.
9. 5.8G FPV real time transmission.
FEATURE:
The materials and specifications stated in this instruction manual
are for reference only.
-1-
Sky warrior K70
Key Introduction of K70 Remote Controller
Specification of K70
Preparation before flight
Basic Operation Guide
Special function button guide
CF mode
Upgrade accessories (Selective Buying)
Drone accessories (Selective Buying)
Trouble Shooting
Catalog
Sky warrior K70
-2-
Wonderful design could win player’s favor.
High pixel and stable flying could bring much more entertainment.
1.LED Light
2.Blade
3.Landing Gear
4.Camera
5.Motor
6.Protect Shield
Key Introduction of K70 Remote Controller
1
1
2
3
4
5
6
2
3
4
5
6
7
8
9
10
11
12
13
14
1. one key to return
2. Short press to take photo/long
press to record video( Point : the
drone will blink one time when
taking photo/blink three times when
recording/blink two times when
saving the photo or video)
3. camera lens up/down
4. left control stick
5. left/right turning trimmer
6. LED light control switch
7. CF mode
8. 3D flip
9. power switch
10. left/right side-fly trimmer/long
press to right side before power
on to switch the left/right control
stick(The remote controller makes
a sound DI indicating the switch
success)
11. forward/backward trimmer
12. right control stick
13. one key to launch/auto landing
(long press 3 seconds to stop)
14. Speed switch (Slow speed-one
sound DI/middle speed-two sound
DI DI/high speed-three sound DI
DI DI)
-3-
Ɣ$LUFUDIW
Ɣ5HPRWHFRQWUROOHU
Ɣ'URQHLQVWDOOWLRQ'LVDVVHPEO\
%DWWHU\LQVWDOOVWLRQ
539mm
159.6mm
163mm
559mm
Specification of K70
LWH 539X559X178MM
Weight Aprx 580g ( Basic version)
Max Flight Time 8 MIN
Operating Temperature Range 0°C to 40°C
Lens Angle Control Range 90°
SD Card Types 4G Micro SD Card
Battery Capacity 2000mAh
LWH 159.6X163X92MM
Weight 233g (without battery)
Operating Temperature Range 0°C to 40°C
Battery 4*1.5V AA
3UHSDUDWLRQEHIRUHIOLJKW
1.Use screwdriver to loose the battery cover in counterclockwise direction as
figure(1)show.
2.Pull out the battery cover and remove it as figure(2)show.
3.Plug the battery into the socket on the drone as figure(3)show.
4.Place the battery into battery base(figure 4).
5.Match the battery cover and base and then fix it.(figure 5).
6.Use screwdriver to tighten the battery cover in counterclockwise direction as
figure(6)show.
-4-
Ɣ/DQGLQJJHDULQVWDOODWLRQ
Ɣ&DPHUDLQVWDOODWLRQGLVDVVHPEO\
Ɣ/DQGLQJJHDUGLVDVVHPEO\
Figure 1 Figure 2
Figure 1 Figure 2
Figure 1 Figure 2
Figure 3
Figure 4 Figure 5 Figure 6
1.Insert the landing gear firmly to the slots on the drone.( Figure1)
2.Use screwdriver to tighten the landing gear in clockwise direction. ( Figure2)
1.Use screwdriver to loose the landing gear in anti-clockwise direction.
2.Take out the landing gear.
&DPHUDLQVWDOODWLRQ
1.Insert the SD card to the camera.
2.Use screwdriver to tighten the camera in clockwise
direction as figure (1)show.
-5-
Ɣ%ODGHLQVWDOODWLRQ'LVDVVHPEO\
Figure 1 Figure 2 Figure 3 Figure 4
Figure 1 Figure 2 Figure 3 Figure 4
&DPHUDGLVDVVHPEO\
1. Use screwdriver to loose the camera in anti-
clockwise direction.
2. Take out the camera.
NOTE: Please make sure the drone is off while mount/dismount the camera.
NOTE: It is important for the correct blade to be put on the correct motor or the
drone will not fly correctly. A letter is marked on each blade to indicate
which motor it should go on.
%ODGHLQVWDOODWLRQ
1.Insert the blade into main axis as figure (1)show.
2.Insert the main axis sleeve into main axis tube as figure (2) show. Make
sure the notch of the main axis sleeve match with the hole on the main axis
tube and then insert the iron axis.
3.Install the iron axis inside the main axis sleeve then rotate it in clockwise
direction in 90°as figure (3) show.
4.Insert the blade cover into main axis as figure (4) show.
%ODGHGLVDVVHPEO\
1.Pull out the blade cover as figure (1) shows.
2.Rotate the main axis sleeve in counterclockwise direction until the iron axis
is match with the notch on the main axis sleeve as figure (2)show.
3.Pull out the iron axis according to figure (3) show. And pull out the main axis
sleeve.
4.Pull out the blade as shown in figure (4).
-6-
Ɣ3URWHFWVKLHOGLQVWDOODWLRQGLVDVVHPEO\
Ɣ0RWRULQVWDOODWLRQ'LVDVVHPEO\
Figure 1 Figure 2
Figure 1 Figure 2
3URWHFWVKLHOGLQVWDOODWLRQ
3URWHFWVKLHOGGLVDVVHPEO\
1.Insert protect shield into the slot on the drone as shown in figure (1).
2.Use screwdriver to tighten the screw on the protect shield in clockwise
direction as shown in figure (2).
1.Use screwdriver to loose the protect shield in anti-clockwise direction.
2.Take out the protect shield.
,QVWDOODWLRQ
1.Insert the motor to the motor base then use screwdriver in clockwise
direction to tighten the screws on the front side of the motor as figure (1)
show.
2.Plug the motor to the motor socket as figure (2) show.
3.Close the motor cover then use screwdriver in clockwise direction to tighten
it as figure (3) show.
See diagram below:
-7-
Ɣ&KDUJLQJWKHEDWWHU\
Figure 1 Figure 2 Figure 3
Figure 1 Figure 2 Figure 3
'LVDVVHPEO\
1. Use screwdriver to loose the screws on the motor cover in anti-clockwise
direction. Figure(1)
2.Pull out the motor socket as figure (2) show.
3.Use screwdriver in counterclockwise direction to loose the screws on the
motor as figure (3) show.
Connect the charger and adaptor, and then connect the 3S plug on the
battery with adaptor, then plug the charger in battery socket, at this time
the red light and green light are on, the green light will off after finished
charging.
Note:1. Cut off the power before you pull out the
battery.
2. Be cautious about the polarity when
connecting the battery and adaptor,
reverse is prohibit.
Note:
In case that the quadcopter might descend to a further or insecure zone due to the
low battery power when flying in outdoor, the quadcopter is specially designed with
the function of secure warning. When the battery power is too low, the led light
would turn from constant on to flickering. Then the operator would have time to
take back the quadcopter and change the battery or recharge it for the next flight.
-8-
Ɣ5HPRWHFRQWUROOHUSUHSDUDWLRQ
1.Take out the battery cover on the back of the controller.
2.Insert 4*1.5V AA battery then put on the battery cover.
Remote controller low power indicator:When the remote controller under low power
status,the light on the remote controller change from constantly in to flicker,and the
buzzer on the remote controller make the alarm sound "DI DI" continuously.
6RIWZDUHLQVWDOODWLRQ
Ɣ6PDUWSKRQHSDGWDEOHWKDUGZDUHVRIWZDUHLQVWDOODWLRQ
Two-dimension code is provided on color box packing and back cover of
specification to scan.
Connection instruction:
1.Turn on the drone, the FPV indicate light blink slowly, which shows the
drone is ready to connect with phone.
2.Open your phone and into “settings” , turn on the WIFI, search the KD-
**** from the signal list, connect the signal, exit “setting” option until the
signal shows connected.
3.Open the PANTONMA APP, click “MY DRONE” into control interface. The
indicate light on the drone will on, which means is connected.The phone
shows the real time image. The wifi signal in full grid showing the
strongest signal.
QR code for google play QR code for IOS QR code for 360
-9-
Ɣ6PDUWSKRQHLQVWDOODWLRQ
Ɣ*)39&RQQHFWLRQ,QVWUXFWLRQ
Figure 1 Figure 2
Antenna
Power switch
Charge socket
Liquid crystal
display (LCD)
Fixation kits
Ɣ*)39GLVSOD\
1.Use screwdriver in anti-clockwise direction to loose the screws in the fixed
clip as figure (1) show.
2.Put the fixed clip on the handle of the controller then use screwdriver in
clockwise direction to tighten it as figure (2) show.
1.Use screw driver to loose the screws on the fixation kits and open the
fixation kits as figure 1 show.
2.Fix the handle on the remote and the fixation kits, and then use
screwdriver in clockwise direction to tighten the screws as figure 2 show.
3.Open the shield cover and turn on the power as figure 3 show.
Figure 1 Figure 2 Figure 3
Table of contents
Other KaiDeng Quadcopter manuals
