Kahuna 2388926 Product information sheet
WWW.KAHUNA.CO.UK
TWO YEAR INTERNATIONAL
WATCH GUARANTEE
AND INSTRUCTIONS
Kahuna certify that this watch has been produced using
first class materials and fully tested before leaving our
Manufacturing Centre. Subject to the conditions stated
below, this watch is guaranteed against defects of material
and manufacture for the period of 2 years from the date of
purchase.
Please note that this guarantee does not cover the following:
Breakages caused through mishandling
or accidental damage.
Normal wear and tear.
Battery, Glass and Strap
WARNING: This watch should only be opened by a qualified
technician with water-resistancy testing equipment. Do NOT
attempt to open it yourself. This guarantee does not affect
your statutory rights. In the unlikely event of a fault arising
under the terms of the guarantee, return the watch DIRECTLY
to the Kahuna service centre, where it will receive expert
When returning your watch please enclose a cheque or
postal order for £5.00, payable to PH Service Centre, to
cover postage and insurance for loss or damage in transit.
We cannot be held liable for loss or damage without this
remittance.
attention and will be returned promptly. Please include, with
your watch, the completed guarantee form & enclose proof of
purchase clearly stating the nature of the fault together with
your FULL NAME AND ADDRESS.
Your watch will not resist water penetration if the crown is not
fully returned to normal, position 1.
DO NOT operate the crown or push buttons in water or when
watch is wet.
• Batteries should only be replaced by a qualified technician
• Water resistant watches are fitted with rubber seals which
should be replaced every 2-3 years to maintain water
resistancy.
• If condensation should appear in the watch then it should
be immediately overhauled as water will corrode the
electronic components inside causing malfunction.
• Remove your watch whilst applying sprays and cosmetics.
• Do not allow contact with any corrosive agent e.g. gasoline,
paint, solvents and adhesives as this may affect the case
and finish.
• After immersion in salt water (if water resistant), rinse the
watch thoroughly in fresh water as salt may render the
moving parts inoperable.
At Kahuna we offer excellent product servicing for watches
outside the guarantee period. Included in the service are the
following:
• Complete movement overhaul.
• Battery replacement.
• Replacement of water resistant rubber seals.
• Case and glass cleaning.
The watch will then be guaranteed against defective
workmanship or materials for a period of six months in
accordance with the exclusive clauses previously stated.
To obtain a price contact the service department on
0121 524 1400
To obtain this service please send your watch directly to
the Kahuna Service Centre together with your cheque or
postal order remembering to enclose your FULL NAME
AND ADDRESS.
To set the time pull out the crown to the first
click position 2.
Turn the crown to set the hour and minute hands.
When the time is set, push the crown back to
the normal position 1.
Pull out crown two clicks to position 3 (time setting) and
move the hands forward until they pass through 12:00
midnight and the calendar changes. Continue turning to
the appropriate time of day taking care to pass through
12:00 once more if setting at a time after 12:00 noon.
Push the crown in one click to position 2 (rapid date
setting). By rotating the crown, the date can be quickly
set without altering the time. This date setting procedure
will need to be followed after the last day of each month
not having 31 days.
Push the crown back
fully to position 1 for
the watch to operate
normally.
To set digital time and calendar
In normal time display press and hold S3 for 3 seconds,
alarm time flashing.
Press S3 again to enter time setting mode with seconds
flashing.
Press S2 to reset second digits to zero – note this will
increase the minute by 1 minute if digits were between 30-59
seconds.
Press S1 – minutes flashing, Press S2 to adjust.
Press S1 – hour flashing, press S2 to adjust.
Press S1 – month flashing, press S2 to adjust.
Press S1 – date flashing, press S2 to adjust.
Press S3 to confirm settings.
To change time display format
In normal time display press and hold S2 and then press
S3 to toggle between 12 hour (A = AM, P = PM) or 24 hour
format.
To change calendar format
In normal time display press and hold S1 and then press S2
to toggle between “month – date” or “date – month” formats.
In normal time display, press and hold S1 to view calendar.
Release to return to normal time display.
To set alarm time
In normal time display press and hold S3 for 3 seconds,
Alarm time hour flashing - press S2 to adjust.
Press S1 – minutes flashing, press S2 to adjust.
Press S3 to confirm.
Alarm now armed with ( ) symbol showing.
In normal time display press and hold S2 to view alarm time.
Release to return to normal time display.
To turn alarm ( ) and hourly chime ( ) on/off
In normal time display press and hold S2 then press S1 to
turn alarm on ( ) symbol showing and daily alarm on ( )
symbol showing or alarm and hourly chime off, no symbol
showing.
When the alarm sounds, press S2 or S3 to disarm.
To use chronograph
In normal time display press S3 once.
Press S1 to start / stop count.
When stopped, press S2 to reset.
During count, press S2 for split count, press S1 to stop then
S2 to show split count.
Press S2 again to reset.
Press S3 to return to normal time display.
To use back light
Press S1 to illuminate back light for approx 4 seconds.
S1S2
S3
