Küppersbusch IKD 976.2 User manual

Bedienungsanleitung

Instructions Booklet

Mode d’emploi

Libretto Istruzioni

Gebruiksaanwijzing

Manual de instrucciones

Manual de Instruções

IKD 976.2IKD 976.2

IKD 976.2

IKDEM 976.2IKDEM 976.2

IKDEM 976.2

Εγχειρίδιοοδηγιών

14GB

CONTENTS

Dear Customer,

If you follow the recommendations contained in this Instruction

Manual, your appliance will give you constant high performan-

ce and will remain efficient for many years to come.

RECOMMENDATIONS AND SUGGESTIONS 15

CHARACTERISTICS 16

INSTALLATION 18

USE 21

MAINTENANCE 22

15GB

650 mm min.

RECOMMENDATIONS AND SUGGESTIONS

INSTALLATION

• The manufacturer will not be held liable for any damages resulting

from incorrect or improper installation.

• The minimum safety distance between the cooker top and the

extractor hood is 650 mm.

• Check that the mains voltage corresponds to that indicated on the

rating plate fixed to the inside of the hood.

• For Class I appliances, check that the domestic power supply

guarantees adequate earthing.

Connect the extractor to the exhaust flue through a pipe of

minimum diameter 120 mm. The route of the flue must be as short

as possible.

• Do not connect the extractor hood to exhaust ducts carrying

combustion fumes (boilers, fireplaces, etc.).

• Iftheextractorisusedinconjunctionwithnon-electricalappliances

(e.g. gas burning appliances), a sufficient degree of aeration must

be guaranteed in the room in order to prevent the backflow of

exhaust gas. The kitchen must have an opening communicating

directly with the open air in order to guarantee the entry of clean

air.

USE

• The extractor hood has been designed exclusively for domestic

use to eliminate kitchen smells.

• Never use the hood for purposes other than for which it has ben

designed.

• Never leave high naked flames under the hood when it is in

operation.

• Adjust the flame intensity to direct it onto the bottom of the pan

only, making sure that it does not engulf the sides.

• Deep fat fryers must be continuously monitored during use:

overheated oil can burst into flames.

• The hood should not be used by children or persons not instructed

in its correct use.

MAINTENANCE

• Switch off or unplug the appliance from the mains supply before

carrying out any maintenance work.

• Clean and/or replace the Filters after the specified time period.

• Clean the hood using a damp cloth and a neutral liquid detergent.

16GB

CHARACTERISTICS

Dimensions

650 min.

732

435

898

500

min. 790

max. 1170

790

135

500

340

17GB

12f

2.1

2.2

12h

7.1

14.1

12g

12e

12c

7.1a

7.1b

Components

Ref. Q.ty Product Components

11 Hood Body, complete with: Controls, Light,

Blower, Filters

21 Telescopic Chimney comprising:

2.1 1 Upper Section

2.2 1 Lower Section

7.1 1 Telescopic frame complete with extractor,

consisting of:

7.1a 1 Upper frame

7.1b 1 Lower frame

81 Air Outlet Grill

91 Reducer Flange ø 150-120 mm

14 1 Hood BodyAir Outlet Extension Piece

consisting of two Half Shells

14.1 1 Air Outlet Connection Extension

15 1 Air Outlet Connection

24 1 Junction box

25 2 Pipe clamps

Ref. Q.ty Installation Components

11 4 Wall Plugs ø 10

12c 4 Screws 2,9 x 6,5

12e 2 Screws 2,9 x 9,5

12f 4 Screws M6 x 10

12g 4 Screws M6 x 80

12h 4 Screws 5,2 x 70

21 1 Drilling template

22 4 6.4 mm int. dia washers

23 4 M6 nuts

Q.ty Documentation

1 Instruction Manual

18GB

INSTALLATION

Drilling the Ceiling/shelf and fixing the frame

DRILLING THE CEILING/SHELF

• Use a plumb line to mark the centre of the hob on the ceiling/support shelf.

• Place the drilling template 2121

2121

21 provided on the ceiling/support shelf, making sure that the template

is in the correct position by lining up the axes of the template with those of the hob.

• Mark the centres of the holes in the template.

• Drill the holes at the points marked:

• For concrete ceilings, drill for plugs appropriate to the screw size.

• For hollow brick ceilings with wall thickness of 20 mm: drill ø 10 mm.

• For wooden beam ceilings, drill according to the wood screws used.

• For wooden shelf, drill ø 7 mm.

• For the power supply cable feed, drill ø 10 mm.

• For the air outlet (Ducted Version), drill according to the diameter of the external air exhaust

duct connection.

FIXING THE FRAME

Before fixing, separate the Upper Section 2.12.1

2.12.1

2.1 and

the Lower Section 2.22.2

2.22.2

2.2 from the Frame by

unscrewing the screws 12c12c

12c12c

12c, then separate the two

sections of the frame by unscrewing the 6 side

screws to obtain the Upper frame and Lower fra-

me.

19GB

Upper frameUpper frame

Upper frame

• Align the power supply cable feed hole

• Fix the upper frame to the ceiling or shelf using:

• For concrete ceilings, use the appropriate plugs for the screw size (not provided).

• For hollow brick ceilings of wall thickness of approximately 20 mm: use 4 plugs 1111

1111

11 and 4

screws 12h12h

12h12h

12h, provided.

• For wooden beam ceilings, use 4 wood screws (not provided).

• For wooden shelf, use 4 screws 12g12g

12g12g

12g with washers 2222

2222

22 and nuts 2323

2323

23, provided.

Lower frameLower frame

Lower frame

• Fix the lower frame using the 8 previously removed screws, adjusting the length according to the

installation height (hood body lower fixing surface must be at least 720 mm from the hob).

• For the recirculation version, turn the frame in the direction chosen for the recirculated air outlet.

• The frame mountings must be secure to withstand the weight of the hood and any stresses caused

by the occasional side thrust applied to the device. On completion, check that the base is stable,

even if the frame is subjected to bending.

• In all cases where the ceiling is not strong enough at the suspension point, the installer must

provide strengthening using suitable plates and backing pieces anchored to the structurally sound

parts.

Connections

DUCTED VERSION AIR EXHAUST SYSTEM

When installing the ducted version, connect the hood to the chimney using either a flexible or rigid

pipe ø 150 or 120 mm, the choice of which is left to the installer.

• To install a ø 120 mm air exhaust connection,

insert the reducer flange 99

9 on the hood body

outlet.

• Fix the pipe using the pipe clamps 2525

2525

25 provided.

• Remove any activated charcoal filters.

RECIRCULATION VERSION AIR OUTLET

• Insert reducer flange 99

9 on the extractor outlet.

• Push fit the extension piece 1414

1414

14 onto the flange.

• Push fit connector 1515

1515

15 onto the extension piece.

• Insert extension piece/connector 14.114.1

14.114.1

14.1 laterally

on connector 1515

1515

15, ensuring that the outlet is in

line with the chimney intake.

120

150

14.1

20GB

12f

12e

Cmd

12c

Lux

Flue assembly - Mounting the hood body

• Position the upper chimney section and fix the

upper part to the frame using the 2 screws 12c12c

12c12c

12c

provided.

• Fit the lower chimney section onto the frame,

holding it in place until the hood body has been

fixed in place.

RecirRecir

Recirculation versionculation version

culation versionculation version

culation version

• Make sure that the outlet of the extension piece

14.114.1

14.1 is horizontally and vertically aligned with

the chimney outlet.

• If this is not the case, remove the lower chimney

section and adjust the position by cutting the

hoodbody extension 1414

1414

14 along one of thethinner

section channels denoting the pre-fixed lenghts,

then reassemble as described previously.

Before fixing the hood body to the frame:

• Remove the grease filters from the hood body;

• Remove any activated charcoal filters.

• From below, use the 4 screws 12f12f

12f12f

12f provided to

fix the hood body to the frame.

• For the recirculation version, locate the

directional grill 88

8 in its housing. Ensure that it

is inserted correctly in connector 1515

1515

15.

ELECTRICAL CONNECTION

• Connect the hood to the mains through a two-

pole switch having a contact gap of at least 3 mm.

• Connect the control connector CmdCmd

CmdCmd

Cmd.

• Connect the lights connector LuxLux

LuxLux

Lux.

• Place the connectors in the junction box 24 and

close it using the 2 screws 12e (2,9 x 9,5)

provided.

• Fix the junction box to the hood body using the

2 screws 12c (2,9 x 6,5) provided.

• For the recirculation version, fit the activated

carbon odour filter.

• Replace the grease filters.

21GB

USE

Control panel

L Light Switches the lighting system on and off.

S1S1

S1 Led Motor running led. Flashes when the grease filters are saturated.

S2S2

S2 Led Intensive speed led. Flasheswhentheactivated carbon odour filters are exhausted.

M Motor Switches the extractor motor on and off at low speed. Used to provide a contin-

uos and silent air change in the presence of light cooking vapours.

V1V1

V1 Speed Reduces the operating speed.

V2V2

V2 Speed Increases the operating speed.

V3V3

V3 Intensive Maximum speed, used for eliminating the highest cooking vapour emission.

speed Switches off automatically after 10 minutes operation. Can also be switched off

manually by pressing the button.

LM V3S1 S2V2V1

22GB

MAINTENANCE

Grease filters

CLEANING METAL SELF-SUPPORTING GREASE FILTERS

Alarm signal resetAlarm signal reset

Alarm signal reset

• Switch off the lights and extractor motor.

• Press button V2V2

V2V2

V2 for at least 3 seconds, until the

leds start to flash.

Cleaning the filtersCleaning the filters

Cleaning the filters

• The filters are washable and must be cleaned

when led S1S1

S1S1

S1 flashes or at least every 2 months

of operation, or more frequently for particularly

heavy usage.

• Remove the filters one at a time by pushing

them towards the back of the group and

pulling down at the same time.

• Wash the filters, taking care not to bend them.

Allow them to dry before refitting.

• When refitting the filters, make sure that the

handle is visible on the outside.

This manual suits for next models

Table of contents

Other Küppersbusch Ventilation Hood manuals

Küppersbusch

Küppersbusch KD 9420.0 GE Operation manual

Küppersbusch

Küppersbusch KD 9420.0 GE-CN Operation manual

Küppersbusch

Küppersbusch EDIP 6600 Specification sheet

Küppersbusch

Küppersbusch EMI 850.0E User manual

Küppersbusch

Küppersbusch KD9980.0TGE Operator's manual

Küppersbusch

Küppersbusch KD 8950.0 Technical manual

Küppersbusch

Küppersbusch IKD3850.0E Operator's manual

Küppersbusch

Küppersbusch EMA 800.0W User manual

Küppersbusch

Küppersbusch KD 9550 User manual

Küppersbusch

Küppersbusch IKD 9600 User manual

Küppersbusch

Küppersbusch EM6-EM10 Quick setup guide

Küppersbusch

Küppersbusch Hood User manual

Küppersbusch

Küppersbusch KD 9475.0 E Operation manual

Küppersbusch

Küppersbusch LB 6500 Specification sheet

Küppersbusch

Küppersbusch IKD9880.0 Quick setup guide

Küppersbusch

Küppersbusch KD7580.0GE Operator's manual

Küppersbusch

Küppersbusch IKD 937.0 GE User manual

Küppersbusch

Küppersbusch IKD9885.0 Operator's manual

Küppersbusch

Küppersbusch EDL12700.0GE User manual

Küppersbusch

Küppersbusch KD635.2 Quick setup guide

Küppersbusch

Küppersbusch EDD9960.OGE Technical manual

Küppersbusch

Küppersbusch EDIP 6550.0 Quick setup guide

Küppersbusch

Küppersbusch KD 9570 OBC Operation manual

Küppersbusch

Küppersbusch CSW6870 0 Series Operation manual

Popular Ventilation Hood manuals by other brands

emmeti

emmeti RECUPA MED A-140 Installation and use manual

Nibe

Nibe F135 user manual

Kuppersberg

Kuppersberg INTRO 60 Technical Passport

Zephyr

Zephyr Spruce AK9834BS Use, care and installation guide

Hisense

Hisense MH6INBG manual

Miele

Miele DA 1255 Operating and installation instructions

Broan

Broan 46000 Specification sheet

GE Profile PV977 Owner's Manual & Installation Instructions

FALMEC

FALMEC FFRIA24W5FS Instruction booklet

Whirlpool

Whirlpool RH2600XL-1 SERIES installation instructions

ETNA

ETNA AV360RVS Instructions for use

JUNO

JUNO JDF603E6 installation manual

Miele

Miele DA 6708 D Operating and installation instructions

Tricity Bendix

Tricity Bendix LE 150 Installation & operating instructions

AEG

AEG X68163BV1 user manual

AEG

AEG 125 D operating instructions

Smeg

Smeg KSEV97X instruction manual

Nibe

Nibe S Series Installer manual