JVC RMP-2580U - Remote Controller For Color... Installation guide
REMOTE CONTROL UNIT
RM-P2580U
Build a Total CCTV Surveillance System
with Programmable 360° Dome Color
Camera TK-C675B that’s Powerful and
Cost Effective
R
䡲Built-in PAN, TILT, and ZOOM controls
䡲Auto Panning
䡲Built-in 8ch Sequential Switcher
Function
䡲Auto Patrol Mode
䡲Auto Alarm Operation
䡲Multi-Alarm Inputs/Outputs
䡲8 Video Inputs/Outputs with
Auto Termination
䡲Area Title
䡲Operation Lock Function
䡲Interface: RS-485 for Camera and
RS-232C for External Unit
SYSTEM
mini
Compact, intelligent, and easy to use, the RM-P2580 CCTV
system remote controller gives you virtually unlimited
control over a network of eight TK-C675B CCTV cameras
connected by up to 1.2 km of communication cable.
It lets you select and control the operation of individual cameras — tilt, pan, zoom,
focus, and iris. But, its real power lies in a range of automatic operations from
Auto Panning and Sequential Switching to Auto Patrol. There is even an Auto Alarm
operation, which you can set up to interrupt pre-programmed operations and view
the scene where an alarm is activated. A comprehensive selection of input/output terminals
also lets you add additional monitors, time-lapse VCR, and other peripherals to further
customize your CCTV system. Best of all, the compact RM-P2580 remote controller lets you
install a multi-component CCTV system at a fraction of the price of previous systems.
Everyfeatureyou’lleverneedfrom
aCCTVsystemremotecontrollerat
apricethatwillsurpriseyou
Built-in PAN, TILT, and ZOOM
Controls
The RM-P2580 lets you select any of
eight JVC TK-C675B cameras it
controls in a surveillance network.
Then, using push-buttons and joy stick
you can control pan, tilt, and zoom to
scan an area or focus on a specific
action. You can also fine-tune picture
quality using Focus and Iris controls.
Auto Panning
Using the remote controller, you can
program automatic panning
movements of individual cameras.
A camera set up for automatic
panning constantly patrols the area
under surveillance with low-speed
horizontal camera movements between
two designated points at a constant
time interval.
Auto Sequence Mode
Press the Auto switch and the
RM-P2580 enters the Auto Sequence
Mode. Using a built-in sequential
switcher the controller sequentially
displays the images captured by a
network of up to eight CCTV cameras.
The cameras are selected in preset
number order with images displayed for
a fixed period.
Auto Patrol Mode
The Auto Patrol Mode provides three
Preset Sequence Mode settings and
64 presettings for surveillance coverage
of a designated area by random or
sequential panning. So you can set up
high-speed camera movements
between multiple pre-set positions in
the sequence and the time intervals of
your choice. You can also use this
function for individual or multiple
cameras.
Auto Alarm Operation
Operation of the RM-P2580 can be
interlocked with peripheral alarm
equipment connected through
Data I/O Terminals at the back of the
unit. The user can then select operation
in either Alarm Priority or Manual
Priority mode. With the Alarm Priority
mode selected, the controller interrupts
the programed operation automatically
at the shot by the camera for which the
alarm signal is received. The controller
also issues visual and audio alarms,
while indicating the camera ID number
on the Camera Display. In Manual
Priority mode only the camera ID is
displayed with all operations remaining
unaffected.
Input/Output Terminals
The RM-P2580 is equipped with a full
range of input/output terminals. These
let you hook the controller up to a bank
of eight monitors, with one monitor
allocated to each camera, as well as
alarm equipment and time-lapse VCR.
The unit’s RS-485 Connection allows
cascaded connection of cameras.
Area Title
The RM-P2580 also takes advantage
of the Area Title function of the
TK-C675B. This innovative function
divides the space covered by a camera
into 16 units, with a 16-character ID
allocated to each unit. At the touch of a
button you can accurately position the
camera to view a designated area.
Key Lock Function
Activating Key Lock disables the joy
stick and operating push-buttons on
the control panel to prevent operating
errors.
RS-232C Interface
The RM-P2580 comes with an
RS-232C terminal to allow control
external components.
POSITION display
AUTO PATROL button
AUTO PAN
button PAN/TILT
control lever
POSITION displaySET button
Camera 1 Camera 2 Camera 3
Camera 6 Camera 5 Camera 4
POSITION display
Lights up.
AUTO button
CAMERA display
q
@3
werty uio
!0!1!3 !2!4!5!6!7!8!9@0@1@2
@9@8@7@6@5
@4 #4 #3 #1 #0#2
q[MENU] button (with an indicator)
w[SET] button
e[ALARM] indicator
r[POWER] indicator
t[KEY LOCK] indicator
y[CAMERA] display
u[POSITION] display
i[AUTO] button
o[F1, F2, F3] Function buttons
!0 [CAMERA] button
!1 [POSITION] button
!2 [PAN/TILT] control lever
!3 [OPTION 1,2]
!4 [AUTO PATROL] button
!5 [-,+] Negative and positive buttons
!6 [AUTO PAN] button
!7 [ENTER] button
!8 [1 to 0/HOME] Numeric key buttons
!9 [CLEAR] button
@0 [ZOOM WIDE, TELE] ZOOM control
buttons
@1 [FOCUS NEAR, FAR] FOCUS control
buttons
@2 [IRIS CLOSE, OPEN] Iris control buttons
@3 [SPEED] Speed button and indicators
@4 [AC~INPUT] AC power input connector
@5 [POWER] switch
@6 [TO CAMERA] Camera control signal
connectors
@7 [DATA I/O] Data signal input/output
terminals
@8 [SERIAL-1] External extension connector 1
(D-sub 9-pin male connector)
@9 [SERIAL-2] External extension connector 2
(D-sub 9-pin male connector)
#0 [MONITOR OUTPUT 2] Video signal
output connector 2
#1 [MONITOR OUTPUT 1] Video signal
output connector 1
#2 [VIDEO INPUT] Video signal input
connectors
#3 [VIDEO OUTPUT] Video signal output
connectors
#4 DIP switch
Controls, Connectors and
Indicators
Printed in Japan
KCN-1771
■The Hachioji Plant of Victor Company of Japan, Ltd., has received ISO14001 Certification
under the global standard for environmental management.
This catalog is printed on recycled paper.
1
TO CAMERATO CAMERA DATA I / ODATA I / O
RXRX+RXRX
-
TXTX+TXTX
-
COMCOM
1 2 3 4 5 6 7 8
COMCOM
9/19/1 10/210/2 11/311/3 12/412/4 13/513/5 14/614/6 15/715/7 16/816/8
COMCOM COMCOM COMCOM
CAMERACAMERA
SWSW
UNITUNIT
ALARMALARM
AUTOAUTO
431 2 875 6
2 3 4 5 6 7 8
1
MONITORMONITOR
OUTPUTOUTPUT MONITORMONITOR
SERIAL-2SERIAL-2SERIAL-1SERIAL-1
VIDEO INPUT
VIDEO OUTPUTVIDEO OUTPUT
OUTPUTOUTPUT
2
1
ON
2 3 4 5 6 7 8
POWER
OFF
ON
AC INPUT
8 (202)
3 (75.5)
SETUPSETUP
MENUMENU SETSET
SPEEDSPEED
IRISIRIS
AFAF
FOCUSFOCUS
ZOOMZOOM
OPENOPEN
FARFAR
TELETELE CLEARCLEAR /HOME/HOME
7
4
1
8
0
5
2
9
6
3
ENTERENTER
AUTOAUTO
PAN
OPTIONOPTION
1OPTIONOPTION
2
CAMERACAMERA
POSI-POSI-
TIONTION
AUTOAUTO
PATROLPATROL
CLOSECLOSE
NEARNEAR
WIDEWIDE
AUTOAUTO F-1F-1 F-2F-2 F-3F-3
PAN/TILTPAN/TILTLENSLENS
CAMERA/POSITIONCAMERA/POSITION
CAMERACAMERA POSITIONPOSITION
REMOTE CONTROL UNITREMOTE CONTROL UNIT
RM-P2580RM-P2580
ALARMALARM
POWERPOWER
KEY LOCKKEY LOCK
11-13/16 (300)
9-1/2 (240) 2-7/8 (73)
3 (75)
1/8 (3)
8 (203)
5-15/16 (150)
1-1/16 (26)
2-1/8 (53)
R
JVC PROFESSIONAL PRODUCTS COMPANY
DIVISION OF JVC AMERICAS CORP.
1700 Valley Road, Wayne, N.J. 07470
TEL: (973) 315-5000, (800) 582-5825
FAX: (973) 315-5030
E-mail: [email protected]
JVC CANADA INC.
21 Finchdene Square, Scarborough, Ontario M1X 1A7
TEL: (416) 293-1311 FAX: (416) 293-8208
Internet Web Site http://www.jvcpro.com/
DISTRIBUTED BY
Design and specifications subject to change without notice.
Specifications
Applicable cameras TK-C675B
Max. number of connected cameras 8(A mode),16 (B mode)
Max. cable length 1.2 km
Control terminals Push terminals (RS-485)
Max. number of DATA l/O terminals 16
Max. number of alarm inputs/outputs 16
Number of UNIT ALARM outputs 1 line (open-collector)
Number of AUTO outputs 1 line (open-collector)
Number of CAM SW circuits 1
Video lines
Number of inputs 8 (BNC)
Level Composite, 1V(p-p)
Number of outputs 2 (BNC)
Supply voltage 100 — 120V AC
Power consumption Approx. 3W
Ambient temperatures: Operating 14°F to 122°F ( -10° to 50°C)
Recommended 32°F to 104°F ( 0° to 40°C)
Mass Approx. 3.3lbs. (1.5kg)
Dimensions Unit: inches (mm)
Basic System Applied System
V.IN
V.IN
3421
MONITOR B
OUTPUT
VIDEO
INPUT
CAM
SW OUT
CAM
IN
MONITOR VCR
OUTPUT
RS-232C
MASTER MONITOR
MONITOR
JVC: SW-D7000U
SW-D8000U
TIME-LAPSE VCR
CAMERA 1
CAMERA 2
CAMERA 3
ID:1
ID:2
ID:3
5 6 7 8
REC
REC STOP REC
CHECK EJECT OPERATE
OPERATE
AC24V
AC24V
AC24V
1
TO CAMERATO CAMERA DATA I / ODATA I / O
RXRX+RXRX
-
TXTX+TXTX
-
COMCOM
1 2 3 4 5 6 7 8
COMCOM
9/19/1 10/210/2 11/311/312/412/413/513/514/614/615/715/7 16/816/8
COMCOM COMCOM COMCOM
CAMERACAMERA
SWSW
UNITUNIT
ALARMALARM
AUTOAUTO
431 2 875 6
2 3 4 5 6 7 8
1
MONITORMONITOR
OUTPUTOUTPUT MONITORMONITOR
SERIAL-2SERIAL-2SERIAL-1SERIAL-1
VIDEO INPUT
VIDEO OUTPUTVIDEOOUTPUT
OUTPUTOUTPUT
2
1
ONON
2 3 4 5 6 7 8
POWER
OFF
ON
AC INPUT
MONITOR
OUTPUT 1
VIDEO
INPUT 1 SERIAL 2
TO
CAMERA
RM-P2580
SWITCHER, etc
DIP SW1 "ON"
1
TO CAMERATO CAMERA DATA I / ODATA I / O
RXRX+RXRX
-
TXTX+TXTX
-
COMCOM
1 2 3 4 5 6 7 8
COMCOM
9/19/1 10/210/2 11/311/3 12/412/4 13/513/5 14/614/6 15/715/7 16/816/8
COMCOM COMCOM COMCOM
CAMERACAMERA
SWSW
UNITUNIT
ALARMALARM
AUTOAUTO
431 2 875 6
2 3 4 5 6 7 8
1
MONITORMONITOR
OUTPUT MONITORMONITOR
SERIAL-2SERIAL-1SERIAL-1
VIDEO INPUTVIDEO INPUT
VIDEO OUTPUTVIDEO OUTPUT
OUTPUTOUTPUT
2
1
ONON
2 3 4 5 6 7 8
POWER
OFF
ON
AC INPUT
V.IN
MONITOR
OUTPUT 2
MONITOR
OUTPUT 1
CAM SW
OUT
VIDEO
IN
COM
CAMERA
SW
AC24V
AC24V
AC24V
TO
CAMERA
TIME-LAPSE VCR
RM-P2580
CAMERA 1
CAMERA 1
CAMERA 1
ID:1
ID:2
ID:3
Camera 1
video
Camera 2
video
Camera 3
video
Camera 4
video
Camera 5
video
Camera 6
video
Camera 7
video
Camera 8
video
MASTER MONITOR
Set Pin 1 to "OFF" for A Mode.
REC
REC STOP REC
CHECK EJECT OPERATE
OPERATE
Other manuals for RMP-2580U - Remote Controller For Color...
1
Table of contents
Other JVC Remote Control manuals
JVC
JVC RM-V717KITU User manual
JVC
JVC RMP-2580U - Remote Controller For Color... User manual
JVC
JVC RM-RK31P User manual
JVC
JVC RM-P210 User manual
JVC
JVC RM-LP57 User manual
JVC
JVC KS-RC106 Guide
JVC
JVC AV-28GH1BUF User manual
JVC
JVC RM-SRX7020J User manual
JVC
JVC RM-P210U User manual
JVC
JVC KS-RC111EU Guide
