Juniper QFX5200-48Y User manual

QFX5200-48Y Quick Start Guide

Published

2023-10-20

RELEASE

Table of Contents

Mounng the QFX5200-48Y

Connecng Power to the Device

Performing the Inial Soware Conguraon for QFX5200 Switches

Safety Warnings Summary

Mounng the QFX5200-48Y

The QFX5200-48Y is available in AC and DC power models. Only mount QFX5200-48Y models in a

four-post rack. This procedure describes the installaon into a four-post rack and connecng AC power.

For DC connecon procedures, see the complete QFX5200-48Y hardware documentaon at hps://

www.juniper.net/documentaon/.

To install a Juniper Networks QFX5200-48Y, you need:

•Electrostac discharge (ESD) grounding strap (not provided)

• One pair of front mounng brackets (provided)

• One pair of adjustable rear mounng blades (provided)

• One pair of rear mounng brackets to aach the mounng blades to the chassis (provided)

• Twenty black at head screws to secure the mounng rails and mounng blades to the chassis

(provided)

• Eight screws and cage nuts to secure the chassis and rack-mount kit to the rack (not provided)

• Two washer head Phillips screws to lock the mounng blades to the rear brackets (provided)

• Screwdriver appropriate for your rack-mounng screws (not provided)

• Two power cords with plugs appropriate for your geographical locaon (provided)

• RJ-45 cable and RJ-45 to DB-9 serial port adapter (not provided)

NOTE: We no longer include a DB-9 to RJ-45 cable or a DB-9 to RJ-45 adapter with a CAT5E

copper cable as part of the device package. If you require a console cable, you can order it

separately with the part number JNP-CBL-RJ45-DB9 (DB-9 to RJ-45 adapter with a CAT5E

copper cable).

• Management host, such as a PC laptop, with a serial port (not provided)

• Grounding cable and lug (not provided)

• Two Phillips screws with star washers to ground the chassis (provided) (For instrucons to aach the

grounding cable and lug to earth ground, see the

QFX5200 Hardware Guide

To mount the switch in a four-post 19-in. rack:

1. Aach the ESD grounding strap to your bare wrist and to a site ESD point.

NOTE: If you are mounng mulple units in the rack, mount the heaviest device at the

boom and mount the others from boom to top in order of decreasing weight. The

QFX5200-48Y weighs between 20.78 lb (9.43 kg) and 21.16 lb (9.6 kg) with power supplies

and fans installed. Installing these devices in a rack or cabinet requires two people to li the

switch and secure it to the rack.

2. Place the rack in its permanent locaon, allowing adequate clearance for airow and maintenance,

and secure it to the building structure.

3. Determine whether the end with the eld-replaceable units (FRUs) or the ports is to be placed at

the front of the rack.

4. Align the holes in the front mounng bracket with the holes on the side of the chassis so that the

bracket is ush with the port panel. See Figure 1 on page 2.

Figure 1: Align the Front Mounng Bracket and Secure with Screws

5. Using a Phillips screwdriver, aach the front mounng bracket to the switch using four of the at

head screws in the holes closest to the port panel. Tighten the screws.

6. Repeat Steps 4 and 5 on the opposite side of the switch.

7. Align the holes in the adjustable mounng rail with the remaining holes in the chassis. The

alignment should permit two screws at mid-chassis and four screws nearest the power supplies.

The adjustable blades t standard racks between 22.05 in. (56 cm) to 29.5 in. (75 cm).

8. Aach the adjustable mounng rail to the chassis using the Phillips screwdriver and six of the at

head screws. Tighten the screws. See Figure 2 on page 3.

Figure 2: Align Holes for Mounng Rail and Aach with Screws

9. Repeat Steps 7 and 8 on the opposite side of the switch.

10. Have one person grasp both sides of the unit, li it, and posion it in the rack so that the front

mounng bracket is aligned with the rack holes.

11. Have a second person secure the front of the device to the rack using four mounng screws (and

cage nuts and washers if your rack requires them). Tighten the screws. See Figure 3 on page 3.

Figure 3: Aach the Front Mounng Bracket to the Rack

12. Connue to support the switch while sliding the rear mounng brackets into the channel of the

adjustable mounng blades and securing the blades and the brackets to the rack. Use four

mounng screws (and cage nuts and washers if your rack requires them) to aach the blades and

rear mounng brackets to the rack. Tighten the screws. See Figure 4 on page 4.

Figure 4: Slide Blades into Mounng Rails and Aach to the Rack

13. Ensure that the chassis is level by verifying that all the screws on the front of the rack are aligned

with the screws at the back of the rack.

14. Secure the mounng rails to the rear mounng brackets using the two washer head screws. Tighten

the screws. See Figure 5 on page 4.

Figure 5: Lock the Mounng Rails to the Rack

15. Aach a grounding cable to earth ground and then aach it to the chassis grounding points. For full

instrucons, see Connecng Earth Ground to a QFX5200 in the

QFX5200 Hardware Guide

Connecng Power to the Device

The device is supplied with two factory-installed power supplies. To connect power to an AC-powered

switch:

1. If the AC power source outlet has a power switch, set it to the OFF (O) posion.

2. Insert the coupler end of the power cord into the AC power cord inlet on the AC power supply

faceplate.

3. Insert the power cord plug into the power source outlet.

4. If the AC power source outlet has a power switch, set it to the ON (|) posion.

5. Verify that the AC and the DC LEDs are lit green and on steadily.

Performing the Inial Soware Conguraon for

QFX5200 Switches

Before you begin connecng and conguring a QFX5200, set the following parameter values on the

console server or PC:

• Baud Rate—9600

• Flow Control—None

• Data—8

• Parity—None

• Stop Bits—1

• DCD State—Disregard

You must perform the inial conguraon of the QFX5200 through the console port using the CLI or

through Zero Touch Provisioning (ZTP). In order to use ZTP to provision the device, you must have

access to a Dynamic Host Control Protocol (DHCP) server, and a File Transfer Protocol (anonymous

FTP), Hypertext Transfer Protocol (HTTP), or Trivial File Transfer Protocol (TFTP) server on which the

soware image and conguraon les are stored. For more informaon about using ZTP for provisioning

the device, see Understanding Zero Touch Provisioning in the

Installaon and Upgrade Guide

To connect and congure the switch from the console:

1. Connect the console port to a laptop or PC using an RJ-45 cable and RJ-45 to DB-9 adapter. The

console (CON) port is located on the management panel of the switch.

2. Log in as root. There is no password. If the soware booted before you connected to the console

port, you might need to press the Enter key for the prompt to appear.

3. Start the CLI.

root@% cli

4. Enter conguraon mode.

root> configure

5. Add a password to the root administraon user account.

[edit]

root@# set system root-authentication plain-text-password

New password:

password

Retype new password:

password

6. (Oponal) Congure the name of the switch. If the name includes spaces, enclose the name in

quotaon marks (“ ”).

[edit]

root@# set system host-name

host-name

7. Congure the default gateway.

• For standard Junos OS systems:

[edit]

root@# set routing-options static route default next-hop

address

• For Junos OS Evolved systems:

[edit]

root@# set system management-instance

root@# set routing-instances mgmt_junos routing-options static route

prefix/prefix-

length

next-hop

default-gateway-ip-address

8. Congure the IP address and prex length for the switch management interface.

• For standard Junos OS systems:

[edit]

root@# set interfaces em0 unit 0 family inet address

ip-address/prefix-length

• For Junos OS Evolved systems:

[edit]

root@# set interfaces re0:mgmt-0 unit 0 family inet address

ip-address/prefix-length

CAUTION: Although the CLI permits you to congure two management Ethernet

interfaces within the same subnet, only one interface is usable and supported.

NOTE: On the QFX5200-48Y, the management port em0 is the top right-hand RJ-45 port on

the port panel.

9. (Oponal) Congure the stac routes to remote prexes with access to the management port.

[edit]

root@# set routing-options static route remote-prefix next-hop

destination-ip

retain no-

readvertise

10. Enable services such as SSH and Telnet.

NOTE: You will not be able to log in to the switch as the root user through Telnet. Root login

is allowed only through SSH.

•The default opon for SSH is yes. Select this to enable SSH.

• The default opon for Telnet is no. Change this to yes to enable Telnet.

11. Commit the conguraon to acvate it on the switch.

[edit]

root@# commit

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual