Juniper T320 User manual
Replacing the T320 Cooling System Components
■Replacing a T320 Fan Tray on page 1
■Replacing a T320 Air Filter on page 5
Replacing a T320 Fan Tray
The T320 router has two front fan trays. The front fan trays install horizontally in
the front of the chassis. Each front fan tray contains six fans. The two front fan trays
are interchangeable, but the rear fan tray is not interchangeable with the front fan
trays. The fan trays are hot-insertable and hot-removable.
1. Removing a T320 Front Fan Tray on page 1
2. Installing a T320 Front Fan Tray on page 2
3. Removing a T320 Rear Fan Tray on page 3
4. Installing a T320 Rear Fan Tray on page 4
Removing a T320 Front Fan Tray
The upper front fan tray is located above the FPC card cage, and the lower front fan
tray is located below the front air filter. Each fan tray weighs about 13.3 lb (6.0 kg).
To remove a front fan tray (see Figure 1):
1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis. For more information
about ESD, see Preventing Electrostatic Discharge Damage to an M Series, MX
Series, or T Series Router.
2. If you are removing the lower fan tray:
a. Unwrap any PIC cables from the spools on the cable management system
and remove the cables from the tray. Arrange the cables so that they do not
block the front of the cable management system and tray, and secure them
with temporary fasteners so that they are not supporting their own weight
as they hang from the connector.
CAUTION: Do not let fiber-optic cable hang free from the connector. Do not allow
fastened loops of cable to dangle, which stresses the cable at the fastening point.
b. Simultaneously pull the two releases on the cable management system. Lift
it up and outward to lock it in place to access the lower fan tray.
3. Loosen the captive screws on the corners of the fan tray faceplate.
4. Grasp the handles and pull the fan tray halfway out of the chassis.
Replacing the T320 Cooling System Components ■1
WARNING: To avoid injury, keep tools and your fingers away from the fans as you
slide the fan tray out of the chassis. The fans might still be spinning.
5. When the fans stop spinning, place one hand under the fan tray to support it
and pull the fan tray completely out of the chassis.
Figure 1: Removing a Front T320 Fan Tray
Installing a T320 Front Fan Tray
To install a front fan tray (see Figure 2):
1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis. For more information
about ESD, see Preventing Electrostatic Discharge Damage to an M Series, MX
Series, or T Series Router.
2. Grasp the fan tray by its handles and insert it straight into the chassis.
3. Tighten the captive screws on each side of the fan tray faceplate to secure it in
the chassis.
4. If you are installing the lower fan tray, follow these steps:
a. Unlock the cable management system and lower it to the fully lowered
position.
b. Rearrange the PIC cables in the cable management system. For more
information about proper cable arrangement, see Maintaining T320 PICs
and PIC Cables.
2■Installing a T320 Front Fan Tray
Figure 2: Installing a Front T320 Fan Tray
Removing a T320 Rear Fan Tray
The rear fan tray is mounted vertically on the right side of the rear of the chassis.
The rear fan tray contains five fans. The fan tray weighs about 7.3 lb (3.3 kg).
CAUTION: To maintain proper cooling, do not operate the router with the rear fan
tray removed for more than one minute.
To remove the rear fan tray (see Figure 3):
1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis. For more information
about ESD, see Preventing Electrostatic Discharge Damage to an M Series, MX
Series, or T Series Router.
2. Loosen the captive screws on the top and bottom of the fan tray faceplate, using
a Phillips (+) screwdriver, number 2.
3. Grasp the handles and pull the fan tray halfway out of the chassis.
WARNING: To avoid injury, keep tools and your fingers away from the fans as you
slide the fan tray out of the chassis. The fans might still be spinning.
4. When the fans stop spinning, grasp the handles and pull the fan tray completely
out of the chassis.
Removing a T320 Rear Fan Tray ■3
Figure 3: Removing a Rear T320 Fan Tray
Installing a T320 Rear Fan Tray
To install a replacement rear fan tray (see Figure 4):
1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis. For more information
about ESD, see Preventing Electrostatic Discharge Damage to an M Series, MX
Series, or T Series Router.
2. Grasp the fan tray by its handles and insert it straight into the chassis.
3. Tighten the captive screws on the fan tray faceplate to secure it in the chassis,
using a Phillips (+) screwdriver, number 2.
4■Installing a T320 Rear Fan Tray
Figure 4: Installing a Rear T320 Fan Tray
Replacing a T320 Air Filter
■Removing a Front T320 Air Filter on page 5
■Installing a Front T320 Air Filter on page 6
■Removing a Rear T320 Air Filter on page 7
■Installing a Rear T320 Air Filter on page 9
Removing a Front T320 Air Filter
The front air filter, located below the FPC card cage in the front of the chassis, and
installs horizontally. The front air filter weighs approximately 1 lb (0.5 kg).The air
filters are hot-insertable and hot-removable.
To remove the front air filter (see Figure 5):
1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.
2. Unwrap any PIC cables from the spools on the cable management system, and
remove the cables from the tray. Arrange the cables so that they do not block
the front of the cable management system and tray, and secure them with
Replacing a T320 Air Filter ■5
temporary fasteners so that they are not supporting their own weight as they
hang from the connector.
CAUTION: Do not let fiber-optic cable hang free from the connector. Do not allow
fastened loops of cable to dangle, which stresses the cable at the fastening point.
3. Simultaneously pull the two releases on the cable management system. Lift it
up and outward to lock it in place to access the air filter.
4. Loosen the captive screws on the corners of the air filter faceplate.
5. Grasp the handles and pull the air filter straight out of the chassis.
6. Remove the filter element from the air filter frame (see Figure 6).
Figure 5: Removing the Front Air Filter
Figure 6: Replacing the Front Filter Element
Installing a Front T320 Air Filter
To install the front air filter (see Figure 7):
1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.
2. Insert the filter element into the air filter frame.
6■Installing a Front T320 Air Filter
3. Grasp the air filter by the handles on its faceplate, and slide it straight into the
chassis.
4. Tighten the captive screws on the corners of the faceplate.
5. Unlock the cable management system, and lower it to the fully lowered position.
6. Rearrange the PIC cables in the cable management system.
Figure 7: Installing the Front Air Filter
Removing a Rear T320 Air Filter
The rear air filter is located at the left rear edge of the chassis. The rear air filter
weighs less than 1 lb (0.5 kg).
To remove the rear air filter:
1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.
2. Loosen the captive screws at the top, center, and bottom of the air filter, using
a Phillips (+) screwdriver, number 2.
3. Grasp the air filter cover by the captive screws, and pull firmly to remove the
cover and honeycomb assembly from the chassis (see Figure 8).
4. Press the filter element inward until it clears the hooks at the top and bottom of
the air filter slot, then push it to the left to unseat it.
5. Move the tabs on the filter element to a horizontal position.
6. Grasp the tabs on the filter element and carefully pull it straight out from the
chassis (see Figure 9).
Removing a Rear T320 Air Filter ■7
Figure 8: Removing the Rear Air Filter
8■Removing a Rear T320 Air Filter
Figure 9: Removing the Rear Air Filter Element
Installing a Rear T320 Air Filter
To install the rear air filter (see Figure 10):
1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.
2. Holding the filter by the tabs, carefully push the filter all the way into the air filter
slot.
3. Holding the filter all the way in, push it to the right side of the slot until it is held
in place behind the hooks.
4. Move the tabs to a vertical position.
5. Place the right edge of the honeycomb against the flange of the air filter slot.
6. Line up the holes at the top, center, and bottom of the honeycomb with the pins
in the slot, and press the honeycomb into place.
7. Replace the air filter cover.
8. Firmly tighten the captive screws at the top, center, and bottom of the filter cover
to secure it to the chassis, using a Phillips (+) screwdriver, number 2.
Installing a Rear T320 Air Filter ■9
Figure 10: Installing the Rear Air Filter
Related Topics ■Preventing Electrostatic Discharge Damage to an M Series, MX Series, or T Series
Router
■Replacing the T320 Connections to Routing Engine Interface Ports
■T320 Routing Engine Interface Cable and Wire Specifications
■Maintaining the T320 Air Filters
■T320 Cooling System Description
■Troubleshooting the T320 Cooling System
Published: 2009-11-11
10 ■Installing a Rear T320 Air Filter
Other manuals for T320
4
Table of contents
Other Juniper Network Router manuals
Juniper
Juniper J2300 User manual
Juniper
Juniper PTX10003-80C Installation instructions
Juniper
Juniper ACX1000 Installation instructions
Juniper
Juniper NetScreen-5GT Wireless User manual
Juniper
Juniper M7i User manual
Juniper
Juniper Day One+ User manual
Juniper
Juniper ACX5448 User manual
Juniper
Juniper ACX Series User manual
Juniper
Juniper PTX5000 Installation instructions
Juniper
Juniper M40 User manual
Juniper
Juniper MX2008 Installation instructions
Juniper
Juniper OCX1100 Installation instructions
Juniper
Juniper J2320 User manual
Juniper
Juniper M10i Installation instructions
Juniper
Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV... User manual
Juniper
Juniper EX2200 Series Installation instructions
Juniper
Juniper PTX3000 Specification sheet
Juniper
Juniper ACX2000 User manual
Juniper
Juniper E120 - RELEASE 11.1.X HARDWARE GUIDE... Installation instructions
Juniper
Juniper M40 User guide
