Juniper PTX10001-36MR User manual

Quick Start Guide

PTX10001-36MR

IN THIS GUIDE

PTX10001-36MR Fixed Packet Transport Router Overview | 1

PTX10001-36MR Fixed Packet Transport Router Overview

IN THIS SECTION

PTX10001-36MR Clearance Requirements for Airflow and Hardware Maintenance | 2

Prepare for the Installation | 3

Unpack the PTX10001-36MR | 3

Mount the PTX10001-36MR in a Rack | 4

Connect the PTX10001-36MR to Ground | 8

Connect AC/HVDC Power to the PTX10001-36MR | 9

Perform the Initial Software Configuration | 11

Safety Warnings Summary | 12

Contact Juniper Networks | 14

Juniper Networks PTX10001-36MR is a fixed-configuration router that features 36 network ports that provide high

density and cost efficient 100-Gigabit and 400-Gigabit Ethernet (GbE) ports in a low-profile 1-U form factor. With 9.6

Tbps of throughput, the PTX10001-36MR is optimally designed for peering, core routing, and infrastructure edge routing

roles in cloud provider, service provider and content provider networks. The high-speed ports support a wide variety of

port configurations that include speeds of 400 Gbps, 100 Gbps, 40 Gbps, 25 GPS and 10 Gbps.

For more information about the PTX10001-36MR hardware, see the PTX10001-36MR Packet Transport Router Hardware

Guide.

For information about features supported on PTX Series routers, see Feature Explorer.

Networks website to activate your hardware replacement service-level agreements (SLAs).

CAUTION: Register product serial numbers on the Juniper Networks website and update the installation

base data if there is any addition or change to the installation base or if the installation base is moved.

Juniper Networks will not be held accountable for not meeting the hardware replacement service-level

agreement for products that do not have registered serial numbers or accurate installation base data.

Update your installation base at

https://www.juniper.net/customers/csc/management/updateinstallbase.jsp.

PTX10001-36MR Clearance Requirements for Airflow and Hardware Maintenance

When planning the site for a PTX10001-36MR installation, you must allow sufficient clearance around the installed chassis

(see Figure 1).

Figure 1: Clearance Requirements for Airflow and Hardware Maintenance for a PTX10001-36MR

g100986

19 in.

(48.26 cm)

Clearance required

for maintenance

24 in. (61 cm) 25.89 in. (65.76 cm)

FRUsPorts

17.36 in.

(44.09 cm)

Clearance required

for maintenance

24 in. (61 cm)

25.47 in. (64.70 cm)

Follow these guidelines:

•For the cooling system to function properly, the airflow around the chassis must be unrestricted. See PTX10001-36MR

Cooling System for more information about the airflow through the chassis.

•If you are mounting a PTX10001-36MR in a rack with other equipment, ensure that the exhaust from other equipment

does not blow into the intake vents of the chassis.

•You must leave at least 24 in. (61 cm) both in front of and behind the PTX10001-36MR for service personnel to remove

and install hardware components. You must leave adequate space at the front and back of the PTX10001-36MR. NEBS

GR-63 recommends that you allow at least 30 in. (76.2 cm) in front of the rack or cabinet and 24 in. (61 cm) behind the

rack.

Prepare for the Installation

To install the PTX10001-36MR, you’ll need two people for installation, one person to lift the device into place and another

person to attach the device to the rack.

You’ll also need to have the following items available (none are provided):

•ESD wrist strap with cable

•Screwdriver appropriate for the rack-mounting screws

•Management host, such as a PC laptop, with a serial port

•Grounding cable—The grounding cable must be 8 AWG (8.4 mm²), minimum 90° C wire, or as permitted by the local

code.

NOTE: The grounding cable requires a Panduit LCD6-14AH-L or equivalent grounding lug. For DC installations,

the grounding lug is provided.

•Two M6 x 10 mm screws and washers.

•Screwdriver appropriate for the M6 x 10 mm screws.

Unpack the PTX10001-36MR

The PTX10001-36MR chassis is a rigid sheet-metal structure that houses the hardware components. The PTX10001-36MR

is shipped in a cardboard carton, secured with foam packing material. The carton also contains an accessory kit and the

Roadmap card with links to the quick start instructions.

CAUTION: PTX10001-36MR routers are maximally protected inside the shipping carton. Do not

unpack the PTX10001-36MR until you are ready to begin installation.

1. Move the shipping carton to a staging area as close to the installation site as possible, but where you have enough

room to remove the system components.

2. Position the carton so that the arrows point up.

3. Open the top flaps on the shipping carton.

4. Remove the accessory kit.

5. Pull out the packing material holding the device in place.

6. Verify that the following components are in the box:

•The chassis with six fan modules and two power supplies installed

•4-post rack mount kit—2 side mounting blades and 2 side mounting rails

NOTE: If you are installing the PTX10001-36MR on a two-post rack, you must order the 2-post rack mount

kit separately.

•Sixteen flathead screws for the mounting brackets (Phillips, M4 x 6 mm)

•For AC/HVDC installations, two power cords with plugs that are appropriate for your geographical location.

NOTE: Power cords are not provided for DC installations.

•For DC installations, four DC power cable lugs

•RJ-45 cable and RJ-45 to DB-9 serial port adapter

•RJ-45 Y-splitter cable

•End User License Agreement

•Roadmap card

7. Save the shipping carton and packing materials in case you need to move or ship the chassis later.

Mount the PTX10001-36MR in a Rack

You can mount a PTX10001-36MR:

•On four posts of a 19-in. rack or a 19-in. cabinet by using the mounting brackets provided with the device.

•On two posts of a 19-in. rack or a 19-in. cabinet. A two-post rack mount kit must be ordered separately.

For four-post rack installation, there are two front mount rails with two matching rear mount blades. This configuration

allows either end of the device to be mounted flush with the rack and still be adjustable for racks with different depths.

The minimum distance the front and rear rack rails can be spaced apart is 23.6 in. (60 cm) front to back. The maximum

distance the front and rear rack rails can be spaced apart is 31.5 in. (80 cm) front to back. (The remainder of this topic

uses rack to mean rack or cabinet.)

CAUTION: PTX10001-36MR routers require two people for installation, one person to lift the device

into place and another person to attach the device to the rack. If you are installing the PTX10001-36MR

above 60 in. (152.4 cm) from the floor, you can remove the power supplies and fan modules to minimize

the weight before attempting to install the PTX10001-36MR (see Remove the AC/HVDC Power Supply

from the PTX10001-36MR and Remove a Fan Module from the PTX10001-36MR).

CAUTION: If you are mounting multiple units in the rack, mount the heaviest unit at the bottom and

mount the others from bottom to top in order of decreasing weight. The PTX10001-36MR weighs

approximately 39.7 lb (18.0 kg). fully loaded.

To mount the PTX10001-36MR on four posts in a rack by using the provided mounting kit:

1. Wrap and fasten the ESD grounding strap to your bare wrist and an connect the other end of the strap to the ESD

point on the device.

2. Decide whether to place the front (port) end or the back (FRU) end of the PTX10001-36MR at the front of the rack.

Position the PTX10001-36MR in such a manner that the AIR OUT labels on components are next to the hot aisle.

3. Align the holes in the mounting rail with the screw holes on the side of the chassis. See Figure 2 to see the proper

alignment for the PTX10001-36MR.

Figure 2: Attach the Front Mounting Rails to the PTX10001-36MR

g100976

4. Attach the mounting rail to the device using the mounting screws. Tighten the screws.

5. Repeat Step 3and Step 4on the opposite side of the device.

6. Have one person grasp both sides of the device, lift it, and position it in the rack so that the front bracket is aligned

with the rack holes.

7. Have a second person secure the front of the device to the rack by using 4 mounting screws (and cage nuts and washers

if your rack requires them). Tighten the screws. See Figure 3.

Figure 3: Attach the PTX10001-36MR to the Rack

g100978

8. Continue to support the PTX10001-36MR while sliding the rear mounting blades into the channel of the side mounting

rails and securing the blades to the rack. Use four mounting screws (and cage nuts and washers if your rack requires

them) to attach the blade to the rack. Tighten the screws. See Figure 4.

Figure 4: Slide Mounting Blades into Mounting Rail

g100977

9. Ensure that the PTX10001-36MR chassis is level by verifying that all the screws on the front of the rack are aligned

with the screws at the back of the rack.

To mount the PTX10001-36MR on two posts in a rack by using the two-post mounting kit that you purchased separately:

1. Wrap and fasten the ESD grounding strap to your bare wrist and an connect the other end of the strap to the ESD

point on the device.

2. Decide whether to place the front (port) end or the back (FRU) end of the PTX10001-36MR at the front of the rack.

Position the PTX10001-36MR in such a manner that the AIR OUT labels on components are next to the hot aisle.

3. Align the hooks and the screw holes on the mounting bracket with the screw holes on the side of the chassis. See

Figure 5 to see the proper alignment for the PTX10001-36MR.

Figure 5: Attach the Two Post Mounting Brackets to the PTX10001-36MR

g100792

4. Attach the mounting bracket to the device using the mounting screws. Tighten the screws.

5. Repeat Step 3and Step 4on the opposite side of the device.

6. Have one person grasp both sides of the device, lift it, and position it in the rack so that the bracket is aligned with the

rack holes.

7. Have a second person secure the device to the rack by using the appropriate mounting screws (and cage nuts and

washers if your rack requires them). Tighten the screws. See Figure 6.

Figure 6: Attach the PTX10001-36MR to a Two-Post Rack

g100793

8. Ensure that the device is level by verifying that all the screws on one side of the rack are aligned with the screws on

the other side of the rack.

Figure 7: The PTX10001-36MR Secured in a Two-Post Rack

g100794

Connect the PTX10001-36MR to Ground

To meet safety and electromagnetic interference (EMI) requirements and to ensure proper operation, you must connect

the chassis to earth ground before you connect it to power. For installations that require a separate grounding conductor

to the chassis, use the protective earthing terminal on the PTX10001-36MR chassis to connect to the earth ground.

NOTE: An AC-powered PTX10001-36MR gains additional grounding when you plug the power supply into a

grounded AC power outlet by using an AC power cord appropriate for your geographical location.

CAUTION: Before you connect power to the PTX10001-36MR, a licensed electrician must attach a

cable lug to the grounding cables and power cables that you supply. A cable with an incorrectly attached

lug can damage the PTX10001-36MR (for example, by causing a short circuit).

NOTE: Mount your device in the rack before attaching the grounding lug to the switch. See Unpack and Mount

the PTX10001-36MR.

Ensure that you have the following parts and tools available (none are provided):

•Grounding cable—The grounding cable must be 8 AWG (8.4 mm²), minimum 90° C wire, or as permitted by the local

code.

•Grounding lug for your grounding cable—The grounding lug required is a Panduit LCD6-14AH-L or equivalent.

•Two M6 x 10 mm screws and washers.

•Screwdriver appropriate for the M6 x 10 mm screws.

To connect a grounding cable to the PTX10001-36MR:

1. Attach a grounding cable to earth ground (such as the rack in which the PTX10001-36MR is mounted) and then attach

it to the chassis grounding point. Figure 8 shows the location of the chassis grounding point.

Figure 8: PTX10001-36MR Grounding Points

g100987

2. Secure the grounding lug to the protective earthing terminal with the washers and screws. See Figure 9.

Figure 9: Connect a Grounding Cable to a PTX10001-36MR Device

g100988

3. Dress the grounding cable and ensure that it does not touch or block access to other device components and that it

does not drape where people could trip over it.

Connect AC/HVDC Power to the PTX10001-36MR

This procedure is for AC/HVDC installations only. For DC installations, see Connect DC Power to the PTX10001-36MR.

CAUTION: Do not mix AC/HVDC and DC power supplies in the same chassis.

The power supplies automatically detect whether there is AC or HVDC input voltage and manage the power accordingly.

Each 3000 W AC/HVDC power supply module has a single AC or HVDC input and provides 12 V of power to the system.

The power supply in a PTX10001-36MR is a hot-removable and hot-insertable field-replaceable unit (FRU). After removing

the power cord from an individual power supply, you can remove and replace it without powering off the router or

disrupting router functions.

Before you begin to connect AC/HVDC power to the PTX10001-36MR:

•Ensure that you have a power cord appropriate for your geographical location available to connect AC power to the

router. See PTX10001-36MR Power Cord Specifications.

•Read General Electrical Safety Guidelines and Warnings and Action to Take After an Electrical Accident.

•Ensure that you have taken the necessary precautions to prevent electrostatic discharge (ESD) damage (see Prevention

of Electrostatic Discharge Damage).

•Ensure that you have connected the PTX10001-36MR chassis to earth ground.

•Ensure that you have an ESD grounding strap.

•If not already installed, install the power supplies in the router. See Maintain the PTX10001-36MR Power Supplies.

NOTE: Each power supply must be connected to a dedicated power source outlet.

To connect AC power to a PTX10001-36MR:

1. Wrap and fasten one end of the ESD wrist strap around your bare wrist, and connect the other end of the strap to the

ESD point on the device.

2. Ensure that the power supplies are fully inserted in the chassis and the latches are secure.

3. Locate the power cord or cords shipped with the PTX10001-36MR; the cords have plugs appropriate for your

geographical location. See PTX10001-36MR Power Cord Specifications.

WARNING: Ensure that the power cord does not block access to router components or drape

where people could trip on it.

4. Connect each power supply to the power sources. Insert the coupler end of the power cord into the AC power cord

inlet on the AC power supply faceplate (see Figure 10).

NOTE: The coupler end of the power cord model is APP-400.

Figure 10: Connect an AC Power Cord to the PTX10001-36MR

g100965

5. If the AC power source outlet has a power switch, set it to the off (O) position.

NOTE: The device powers on as soon as power is provided to the power supply. There is no power switch

on the device.

Other manuals for PTX10001-36MR

Table of contents

Other Juniper Network Router manuals

Juniper

Juniper PTX10003-80C Installation instructions

Juniper

Juniper MX2010 User manual

Juniper

Juniper MX960 User manual

Juniper

Juniper J4300 User manual

Juniper

Juniper ACX710 User manual

Juniper

Juniper PTX10002-60C User manual

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS - E SERIES END-OF-LIFE MODULE GUIDE... User manual

Juniper

Juniper MX2020 User manual

Juniper

Juniper ACX1000 Installation instructions

Juniper

Juniper EX6210 User manual

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - E120 AND E320 MODULE GUIDE REV... User manual

Juniper

Juniper SSR1200 Installation instructions

Juniper

Juniper T Series Installation instructions

Juniper

Juniper M5 User manual

Juniper

Juniper J4350 User manual

Juniper

Juniper PTX5000 Installation instructions

Juniper

Juniper ACX2200 User manual

Juniper

Juniper PTX10001-20C User manual

Juniper

Juniper ACX1000 Installation instructions

Juniper

Juniper EX9200 Series Specification sheet

Juniper

Juniper T1600 Installation and operation manual

Juniper

Juniper J2300 User manual

Juniper

Juniper QFX10002 User manual

Juniper

Juniper T320 Installation instructions

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview