Juniper JCS 1200 User manual

Replacing a JCS 1200 Management Module or Module Filler

Topics include:

■Removing a JCS 1200 Management Module or Module Filler on page 1

■Installing a JCS 1200 Management Module or Module Filler on page 2

Removing a JCS 1200 Management Module or Module Filler

Figure 1 on page 1 shows how to remove and install a management module.

Figure 1: Removing and Installing a JCS 1200 Management Module

When you remove a management module, keep in mind the following:

■These instructions assume that the JCS 1200 platform is connected to power.

■If you are replacing the only management module in the JCS 1200 platform and

the management module is functioning, save the configuration file before you

proceed. For information about saving and restoring a configuration file, see the

JUNOS Protected System Domain Configuration Guide.

■If you have just installed a second management module in the JCS 1200 platform,

do not remove the first (primary) management module for up to 45 minutes;

the second (redundant) management module needs the time to receive initial

status information and firmware from the management module.

To remove a management module or module filler (see Figure 1 on page 1):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and

connect the strap to one of the ESD points on the chassis.

2. Pull the management module release handle to the open position. The module

moves out of the bay approximately 0.25 in. (0.6 cm).

3. Slide the management module out of the bay.

Replacing a JCS 1200 Management Module or Module Filler ■1

Installing a JCS 1200 Management Module or Module Filler

Figure 2 on page 2 shows how to remove and install a management module.

Figure 2: Removing and Installing a JCS 1200 Management Module

To install a management module or module filler (see Figure 2 on page 2):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and

connect the strap to one of the ESD points on the chassis.

2. Remove the management module filler, if one is installed.

3. Remove the management module interposer filler tray, if one is installed.

4. Install the management module interposer, if it is not already installed.

5. Make sure that the release handle on the management module is in the open

position.

6. Slide the management module into the management module bay until it stops.

7. Push the management module release handle to the closed position.

8. Connect any cables to the management module.

9. If the JCS 1200 platform is connected to power, make sure that the OK LED on

the management module is lit. If the management module is redundant, wait at

least 45 minutes for the modules to copy the configuration data before you make

any changes to the management module configuration.

Related Topics ■Preventing Electrostatic Discharge Damage to the JCS 1200 Platform

■JCS 1200 Management Module Description

■Replacing a JCS 1200 Management Module Filler Tray

■Locating the JCS 1200 Management Module Serial Number

2■Installing a JCS 1200 Management Module or Module Filler

Other manuals for JCS 1200

6

Table of contents

Other Juniper Network Router manuals

Juniper

Juniper M10i User manual

Juniper

Juniper MX240 User manual

Juniper

Juniper ACX6160 User manual

Juniper

Juniper MX5 User manual

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV... User manual

Juniper

Juniper NFX150-S1 User manual

Juniper

Juniper T1600 Installation and operation manual

Juniper

Juniper M10i Installation and operating instructions

Juniper

Juniper E-Series Installation instructions

Juniper

Juniper MX150 User manual

Juniper

Juniper ACX1000 User manual

Juniper

Juniper E120 User manual

Juniper

Juniper ACX1000 Installation instructions

Juniper

Juniper M120 Installation instructions

Juniper

Juniper M10i Installation instructions

Juniper

Juniper ACX2200 Installation instructions

Juniper

Juniper MX104 Installation instructions

Juniper

Juniper T4000 - User manual

Juniper

Juniper ACX1000 Installation instructions

Juniper

Juniper M5 Operating and maintenance manual

Juniper

Juniper EX9214 Installation instructions

Juniper

Juniper ACX4000 User manual

Juniper

Juniper PTX1000 Installation instructions

Juniper

Juniper J-Series Instruction Manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview