JUMO DTRANS p02 User manual

dTRANS p02

Pressure Transmitter

B 40.4385

Operating Instructions

07.01/00365643

All manuals and user guides at all-guides.com

all-guides.com

All manuals and user guides at all-guides.com

Contents

1 Typographical conventions __________________________ 4

1.1 Warnings ____________________________________________________ 4

1.2 Note signs ___________________________________________________ 4

2 General ____________________________________________ 5

2.1 Preface _____________________________________________________ 5

2.2 Application __________________________________________________ 6

3 Delivery package ___________________________________ 7

4 Instrument identification _____________________________ 8

4.1 Nameplate __________________________________________________ 8

4.2 Type designation _____________________________________________ 9

4.3 Dimensions/details __________________________________________ 10

4.4 Dimensions: "non-flush pressure connections" __________________ 10

4.5 Dimensions: "flush pressure connections" ______________________ 11

5 Instrument description _____________________________ 12

5.1 Technical data _____________________________________________ 12

6 Mounting __________________________________________ 14

6.1 General ____________________________________________________ 14

6.2 Prior to mounting ____________________________________________ 14

6.3 Mounting by the pressure connection __________________________ 15

6.4 Mounting by the housing _____________________________________ 15

6.5 Pressure connection _________________________________________ 16

6.6 Use inside the Ex area _______________________________________ 16

7 Installation ________________________________________ 17

7.1 Electrical connection _________________________________________ 17

7.2 Testing the output signal _____________________________________ 19

7.3 Connection of a HART®modem ______________________________ 19

7.4 Connection of a HART® communicator ________________________ 20

7.5 Testing the HART®communication ____________________________ 20

7.6 Electrical connection in the hazardous (Ex) area _________________ 21

All manuals and user guides at all-guides.com

Contents

8 Commissioning ____________________________________ 23

8.1 Characteristic _______________________________________________ 23

8.2 Self-test ____________________________________________________ 24

8.3 Measuring the absolute pressure ______________________________ 26

8.4 Measuring the gauge pressure ________________________________ 29

9 Adjustment options ________________________________ 32

9.1 The level concept ___________________________________________ 32

9.2 Sequence for keypad operation _______________________________ 33

9.3 Display level ________________________________________________ 34

9.4 Parameter level _____________________________________________ 35

9.5 Detailed explanations ________________________________________ 38

10 Opening the instrument ____________________________ 41

10.1 Unscrewing the bezel ring or housing cover ____________________ 41

11 Rotating the instrument ____________________________ 42

11.1 Rotating ____________________________________________________ 42

12 Maintenance _______________________________________ 43

12.1 Trouble-shooting ____________________________________________ 43

13 Appendix __________________________________________ 46

13.1 EC Type-Examination Certificate ______________________________ 46

13.2 Supplement to EC Type-Examination Certificate ________________ 52

13.3 EU Declaration of Conformity ATEX ____________________________ 56

13.4 Settings ____________________________________________________ 58

All manuals and user guides at all-guides.com

1 Typographical conventions

1.1 Warnings

1.2 Note signs

Danger

This sign is used when there may be danger to personnel if the instructions

are disregarded or not followed accurately!

Caution

This sign is used when there may be damage to equipment or data if the

instructions are disregarded or not followed accurately!

Note

This sign is used when your special attention is drawn to a remark.

➩Reference

This sign refers to further information in other chapters or sections.

abc1Footnote

Footnotes refer to certain points in the text. Footnotes consist of two parts:

Markings in the text and the footnote text.

The markings in the text are arranged as continuous superscript numbers.

✱Action

This sign indicates that an action to be performed is described.

The individual steps are marked by this asterisk.

Example:

✱Remove crosspoint screw.

✱Press the key.

All manuals and user guides at all-guides.com

all-guides.com

2 General

2.1 Preface

Please read these Operating Instructions before commissioning the instru-

ment. Keep the manual in a place which is accessible to all users at all times.

Please assist us to improve these operating instructions where necessary.

Your suggestions are welcome.

Phone Germany (0661) 6003-714

abroad (+49) 661 6003-0

Fax Germany (06 61) 6003-605

abroad (+49) 661 603-607

All necessary settings are described in this manual. If any difficul-

ties should still arise during commissioning, you are asked not to

carry out any unauthorized manipulations on the unit. You could

endanger your rights under the instrument warranty!

Please contact the nearest subsidiary or the main factory in such a

case.

When returning modules, assemblies or components, the regula-

tions of EN 100 015 “Protection of electrostatically sensitive com-

ponents” must be observed. Use only the appropriate ESD pack-

aging for transport.

Please note that we cannot accept any liability for damage caused

by ESD.

ESD=electrostatic discharge

All manuals and user guides at all-guides.com

2 General

2.2 Application

General The type JUMO dTRANS p02 is used to measure the pressure of corrosive

and non-corrosive gases, vapors and liquids. The pressure transmitter uses

the piezo-resistive effect to make the measurement. The output signal is a pro-

portional DC current which is linearly proportional to the input pressure.

Version with

Ex protection The JUMO dTRANS p02 pressure transmitter in intrinsically safe version

marked II 1/2 G EEx ia IIC T6, is suitable for mounting within the hazardous

area Zone 1 for connection to Zone 0.

The EC Type-Examination Certificate for the JUMO dTRANS p02 is:

PTB 98 ATEX 2194

If this pressure transmitter is used in areas with potentially explosive atmo-

spheres, the appropriate regulations for installing and operating equipment in

such areas must be observed.

The diaphragms of the JUMO dTRANS p02 pressure transmitter

must not be damaged. Do not insert any objects into the bores of

the pressure connections!

All manuals and user guides at all-guides.com

3 Delivery package

Operating

Instructions

B 40.4385

These operating instructions are a comprehensive guide for the installation,

electrical connection, commissioning, operation and parameterization of the

JUMO dTRANS p02 pressure transmitter.

JUMO

calibration

certificate

A JUMO calibration certificate and a setup print-out comes with each pressure

transmitter. These documents contain information on the parameter settings

and/or the measured characteristic data for the transmitter concerned.

If this calibration certificate is lost, or should you need an additional one, it can

be ordered from JUMO stating the serial No. of the pressure transmitter (see

nameplate),

➩see addresses of suppliers on the back of the operating instructions

Setup

program All the parameters of the transmitter can be conveniently checked and

adjusted by using the setup program. Furthermore, additional functions are

available such as:

- recording of measurements

- graphical display of temperature and pressure

- comprehensive diagnostic messages

- indication of the complete order code and instrument configuration

(for repeat orders).

The setup program is available on request, at extra cost,

Sales No. 40/00365072.

HART®modem The HART®modem serves to connect the JUMO dTRANS p02 to a PC. The

HART®modem is available on request, at extra cost,

Sales No. 40/00345666.

Power supply A supply unit with a supply isolator is available on request, at extra cost,

Sales No. 40/00389710.

All manuals and user guides at all-guides.com

4 Instrument identification

4.1 Nameplate

Nameplate on a pressure transmitter without approval for use within the

hazardous (Ex) area.

Nameplate on a pressure transmitter with approval for use within the hazard-

ous (Ex) area.

All manuals and user guides at all-guides.com

Other manuals for dTRANS p02

Table of contents

Popular Transmitter manuals by other brands

NIVELCO

NIVELCO EasyTREK SCA-300 Series Programming manual

Honeywell

Honeywell 5816WMBR installation instructions

Kamstrup

Kamstrup READy MTU Installation and operation guide

Omega

Omega ZW Series user guide

ABB

ABB Field 264H Instructions for installation

Alinco

Alinco DJ-V17T Service manual

Dejero

Dejero EnGo 3x manual

Rosemount

Rosemount 4600 Reference manual

Speaka Professional

Speaka Professional 2342740 operating instructions

trubomat

trubomat GAB 1000 instruction manual

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 instructions

Rondish

Rondish UT-11 quick start guide

MG 10JRE instruction manual

Burkert

Burkert 8177 operating instructions

Firetide

Firetide HotPort 3203 Hardware installation guide

Tele Radio

Tele Radio T9-02 User instructions

Rotronic

Rotronic HygroFlex HF3 Series user guide

Jamara

Jamara FCX6 Pro Tel Instruction

JUMO dTRANS p02 User manual

Popular Transmitter manuals by other brands