JUITA JT-1512B User manual
Attention: read this manual please, when
using this product
JT-1512B
Garment Template Cutting Machine
(USER MANUAL)
Microsoft is a U.S. registered trademark of Microsoft Corporation. Windows
is a registered trademark of Microsoft Corporation
Preface
Thanks for choosing the JUITA Template Cutting Machine.
The JUITA enjoys not only the beautiful design but also the high
precision, strong compatibility, which can operate with the CAD of
HPGL. Besides, it operates fast and stable.
Before using this template cutting machine, you’d better read this
manual to make sure that you will work with it effectively. If you have
any questions, you will go to the local sellers for further help!
With the easy upgrading of the garment template cutting machine and its
plotting software, we will develop and improve their functions to meet
our customers’ individual demands. This manual is subject to change
without notice. If you have any questions, please contact us.
Chapter 1. Safety Notice
Safety notice: before using this template cutting machine, please read the
following instructions:
1.
The template cutting machine should be installed horizontally. If the template
cutting machine is in uneven status, it cannot work normally.
2.
After installation, you should adjust the height of stand until the machine is in a
horizontal state. The GTCM shall not be installed on the vibrating or unstable
ground.
3.
Please connect this machine to the power supply according to the machine’
rated voltage. Don’t connect the GTCM to the socket with unstablevoltage.
The unstable power may result in the performance degradation, and damage
the power panel. If the power is not stable, please install the regulator.
4.
The plug should be connected to the panel with the ground wire. Don’t move
out plug’s needle. If the machine is not connected with the ground wire, the
ESD will harm the human body and damage the parts of the machine.
5.
Don’t connect the GTCM with the photoprinter, air-conditioner or other power
consumption machines on the same line. If the GTCM is connected with
other power consumption machine in parallel, the sum of their power should
not be bigger than the max power of the plug.
6.
Don’t use the wearing power line. Please pull the plug out of the socket when
the machine is not used in a long time.
7.
When you clean the GTCM firstly, you have to pull the plug out. Don’t let the
liquid draw into the machine, otherwise it may cause short circuit or damage
to the template cutting machine.
8.
Don’t maintenance or dismantle this machine without any instructions that
stated in this manual. Don’t clog or place other goods in the machine working
room.
9.
During the operation of the GTCM, don’t put your hands into the machine or
touch the trolley and otherparts.
Model of the
Product
Series Number of the product
Please check whether the voltage
of AC power corresponds to the
marked voltage on the label.
Chapter 2. Application Notice
Whether you are familiar with the template cutting machine for garment
template or not, please read the following application notice:
2.1
application condition
(1)
The operating temperature range of o Celsius to 35 Celsius. Don’t put or
operate this machine under the intense light, radiation or the thermal
energy.
(2)
The operating humidity under room temperature ranges from 20% to
80%. Don’t use the machine in the wet and dust condition. Once the
water vapor condensed in the machine with the dust, the short circuit or
bad contact will happen, which effects the operation of the machine.
(3)
Don’t put the milling plotter in the harsh EMI environment or beside the
magnetic items.
2.2
other notices:
(1)
Don’t move the GTCM’s holder by hand, otherwise the GTCM may be
damaged.
(2)
Except take on or off the GTCM, don’t screw the fixed nuts on the
holder.
(3)
Don’t add lubricant into the , otherwise the machine may not
operate very well.
(4)
After using the GTCM, please cover the dust proof.
(5)
Don’t switch on or off the machine unnecessarily, otherwise it may affect
the functions of the electronic components.
(6)
During the operation, don’t stand against to the machine or put hands on
the track’s cover.
(7)
If you want to connect or regulate the signal wire, you should make sure
the machine is power off.
3.1
Introduction
Chapter 3. Introduction
The garment template cutting machine mainly deals with the
cutlery of the complicated graphs or words. With high precision and
stability, it enjoys beautiful design. Except that, it is also easily to
control with.
Specification
Material : Nonmetal; Single piece or in a roll;
Original coordinate setting：setting the original point by user.
Max speed of milling and drawing：1200mm/sec
Mechanical resolution：0.025mm/step
Software resolution：0.025mm/step
Distance accuracy：0.15% or 0.1mm
Minimum size of character：5mm*5mm
Repeat position precision：≤0.2mm
Pressure of the tool：50G-500G
Movement acceleration：5g
Communication ：USB2.0，blue tooth transmitting；
Embedded processer：Using 32Bits DSP with 256Mb
Motor driver：AC servo motor driver
Plotting tool movement speed：50 times/sec
Power Supply：170V/250v 50-60H 300W(max)
3.2
requirement of the software and hardware
：
The CAD/CAM software should be compatible with the HP-GL：
Select the software that support the HP-GL；special format can be
ordered；
Hardware：Better than the minimum of the mainstream computer
3.3
consumptive materials
Tools：milling tools of 2—4MM 、special cutting tools
Material: PVC sheet、Kraft paper in roll、single kraft paper、and other
materials.
Chapter 4. Installation
4.1
The items included in the packing of the machine:
1、machine table 1
□
2、lateral stand 2
□
3、support beam 4
□
4、power cable 1
□
5、signal cable 1
□
6、roll paper bar 1
□
7、cutter holder 1、pen holder 1
□
8、screw 10、inner hexagon spanner 2
□
9 milling tool 2、a box of cutting tools
□
10、Manual 1
□
12、warranty card
□
13、CD 1
□
4.2
Installation of the Stand and the machine table: (the instructor of the
machine as following pictures)
Table of contents
Popular Cutter manuals by other brands
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Original instructions
Makita
Makita DCS552 instruction manual
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 user manual
Makita
Makita 4112HS instruction manual
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S manual
Hitachi
Hitachi CM 4SB2 Safety instructions and instruction manual
