JL Audio Stealthbox 011180 User manual

➔

Stealthbox®

INSTALLATION GUIDE

SB-T-TUNCNSL2/10W3v2, JL AUDIO, Inc 2005 Sheet SKU#011180 Revision 4/6/2005Page 1

for the

SB-T-TUNCNSL2/10W3v2

(‘03-Up Toyota Tundra Access & Double Cab

with front bucket seats and center console)

This Stealthbox is a product which

requires professional installation skills and

tools.

Please read this installation guide thor-

oughly before beginning the project. It

will guide you step by step through the

installation.Several of the steps in this

process may require two people to

accomplish.

It is absolutely vital that the enclosure

be properly mounted to the vehicle

according to these instructions. Failure

to mount the enclosure properly pres-

ents two problems: 1)The sub-bass

performance will suffer due to the

movement of the enclosure caused by

the force exerted by the woofer(s) and

2) A loose enclosure presents a serious

safety hazard in the event of a collision

or sudden deceleration.

Please enjoy your JLAudio Stealthbox

responsibly.

STEP 1:

Using a 14mm socket,remove the

four bolts that secure the passenger side front

seat.

STEP 2:

Tilt the seat to the rear, unplug the

exposed wire assembly,remove the seat from

the truck.

STEP 3:

Remove the front storage access

door. Using a 10mm socket,remove the

exposed bolts.

STEP 4:

With the main storage door open,

grab ahold of the black cup holder section

and pull up.

STEP 5:

Using a 10mm socket,remove the

exposed bolts. Also remove the bolts that are

located at the bottom of the main storage

bucket.

STEP 6:

Remove the plastic buttons that are

located on each side of the center console.

START

HERE

Continued on Next Page ➔

www.jlaudio.com

➔

➔➔

➔➔➔

STEP 7: Slide the center console to the rear of

truck.This will allow exposer of the 12v plug wires.

Unplug and then remove the center console from

truck. *Tundra Access Cab Only*

Keep the air ducts inside the truck, for now.

STEP 11: Back inside the truck. Remove the black

bracket that is mounted to the floor of the

truck(not pictured).

*Tundra Access Cab Only*

Using a 1/2” drill bit and drill. Enlarging the mounting

holes from the bracket.

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 8: *Tundra Access Cab Only*

With the center console out of the truck, flip up

side down.Remove the two air duct ears that are

located to the rear of the center console.

*Tundra Access Cab Only*

STEP 12: Cut 1-1/2” off of each carpet flap, that is

located in front of the mounting holes, from

STEP10.

➔

*Tundra Access Cab Only*

STEP 13(a): Place only one of the supplied wax

squares into this location.

Place the middle of the supplied wax square,4-3/4”

back from the front consoles metal mounting brack-

et.

*Tundra Double Cab Only*

STEP 13(b)

FRONT WAX SQUARE

Place the middle of one of the supplied wax

squares, 4-3/4” back from the front consoles metal

mounting bracket.

REAR WAX SQUARES

Place the middle of the remaining pair of supplied

wax squares, 1-3/4” back from the center console

rear mounting holes.

STEP 9: Remove the 8 screws that is securing

the black plastic support to the outer console. Not

all circles represent all 8 screws.

There are a pair of screws on each side of the con-

sole that need to be removed.

STEP 10: *Tundra Access Cab Only*

Now it is time to remove those air ducts from

STEP 7.With the ducts removed, you will need to

cut both ducts. Place the ducts so the front of the

ducts are facing to the right.

Driver’s side: Measure and mark 3/4” from front

of foam tape, back. Cut at location.

Passenger’s side: Cut at the middle of the foam

tape.

SB-T-TUNCNSL2/10W3v2, JL AUDIO, Inc 2005 Sheet SKU#011180 Revision 4/6/2005Page 2

www.jlaudio.com

Passenger’s side

middle

Driver’s side 3/4”

4-3/4” 6-1/2”

1-3/4”

➔➔

➔

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 14: Thread in the three supplied socket cup

set screws into the Stealthbox.Make sure that the

socket ends are on the outside of the Stealthbox.

The rear(left side of pic) threaded rods need to

protrude about 1 1/4” out of the Stealthbox.The

front socket cup set screw needs to protrude about

3/4”.

Place the Stealthbox into location.Slide the rear

socket cup set screw through the drilled out holes

from STEP10. Press firmly on the front of the

Stealthbox,marking the wax square.

STEP 16(a): *Tundra Access Cab Only*

Remove the Stealthbox.You should have an impres-

sion on the wax square.

*CAUTION*

Before drilling, make sure that you are not going to

be drilling into any gas lines, brake lines,transmission

lines, electrical wiring, transfer case(4x4 vehicles) or

anything else that might cause a reduction in your

weekly pay.Always wear eye protection when drilling.

With the use of a 1/2” drill bit and drill. Drill out the

floor at the impression on the wax square

STEP 16(b): *Tundra Double Cab Only*

Remove the Stealthbox.You should have an impres-

sion on the wax square.

*CAUTION*

Before drilling, make sure that you are not going to

be drilling into any gas lines, brake lines,transmission

lines, electrical wiring, transfer case(4x4 vehicles) or

anything else that might cause a reduction in your

weekly pay.Always wear eye protection when drilling.

With the use of a 1/2” drill bit and drill. Drill out the

floor at the impression on the wax square

SB-T-TUNCNSL2/10W3v2, JL AUDIO, Inc 2005 Sheet SKU#011180 Revision 4/6/2005Page 3

www.jlaudio.com

STEP 15: Place the Stealthbox into position,Press

down firmly.

➔

➔➔➔

STEP 23: Apply a supplied flat washer, lock wash-

er and nut onto the three socket sup set screw.

Tightly secure all three nuts..

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 17: Remove the wax square and run speak-

er wire.

STEP 21: Place the Stealthbox/center console into

vehicle.Attach the speaker wire to terminal.

Back out the three socket cup screws to 1-1/4:”.

➔

STEP 22: Place Stealthbox/center console upright

and into the proper position. Carefully guiding the

threaded rods through the three drilled holes.

Pop in the four supplied black plastic push rivets,

into the screw holes on each side of the center con-

sole.

STEP 20: Place the Stealthbox into the center

console,outside of vehicle .

*Double Cabs Only*

The permanent removal of the rear seat 12v plug is

neded.

STEP 18: *Access Cabs Only*

Replace the modified A/C ducts from STEP 10,

back into the vehicle.

(Stealthbox is only shown in the picture for position

purposes.You do not have to have the Stealthbox in

location to accomplish this step)

STEP 19: With the Stealthbox and the modified

A/C ducts in position. Place the front section of the

center console back into the proper location. Do

not secure at this time.

*Remember to plug in the 12v sockets.*

(Stealthbox is only shown in the picture for position

purposes.You do not have to have the Stealthbox in

location to accomplish this step)

SB-T-TUNCNSL2/10W3v2, JL AUDIO, Inc 2005 Sheet SKU#011180 Revision 4/6/2005Page 4

www.jlaudio.com

STEALTHBOX WALL THREADED INSERT

VEHICLE SHEET METAL

FENDER WASHER SOCKET CUP SET SCREW

LOCK WASHER

FLAT WASHER

HEX NUT

Specifications:

Enclosure Type: Sealed

Driver Type: 10W3v2-D2

Nominal Impedance: 4Ω

Cont. Power Handling: 300Watts

JLAudio recommends using a high quality amplifier such as the JLAudio 250/1. The diagram below shows the recommended

crossover,infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.

Included Hardware:

3) Wax Squares

3) 3/8”- 1-1/4” FenderWasher

3) 3/8” Flat Washer

3) 3/8” Split LockWasher

3) 3/8”-16x2-1/4” Socket Cup Set Screw

3) 3/8”-16 Hex Nut

10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: 954.443.1100 Fax: 954.443.1111

JL AUDIO 250/1

monoblock subwoofer amplifier

Amplifier Input Section

Input Sens.

Input Voltage

Low/High

Left Ch. Right Ch.

Signal Sensing

Off/On

Output Mode

Full-Range/Low-Pass/High-Pass

Left Ch. Right Ch.

Amp LP Filter

Mode/Slope

Off/12dB/24dB

Filter Freq. (Hz)

Bass Control

LF Boost (dB)

Off/30Hz

Infrasonic Filter

+1 +13

+10

Preamp Output Section

+12VDC Ground Remote

The JLAudio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information

about installing and tuning this amplifier.

➔➔

STEP 24: With the Stealthbox securely mounted

to the vehicle. Secure the plastic console to the

floor, using the factory screws from STEP 5.

STEP 25: Secure the front section of console with

the factory screws, from STEP 3.

Once both portions of the center console have

been secured. Snap in the cup holders from

STEP 4, front console storage door from STEP 3

and the plastic buttons from STEP 6.

➔

SB-T-TUNCNSL2/10W3v2, JL AUDIO, Inc 2005 Sheet SKU#011180 Revision 4/6/2005Page 5

www.jlaudio.com

Mid/High Frequency Driver Information:

CONGRATULATIONS!

INSTALL COMPLETE.

VR650-CSi

VR650-CXi

Front Location Driver Size:

6.5”

Applicable JL Audio Products:

TR,VR, XR, ZR 650-CSi

mounting plates are needed

Rear Location Driver Size:

6.5”

Applicable JL Audio Products:

TR,VR,XR 650-CXi

mounting plates are needed

Cont.

From

Page

Difficulty Of Installation:

This manual suits for next models

Other JL Audio Subwoofer manuals

JL Audio

JL Audio 12W3v2 User manual

JL Audio

JL Audio 94350 User manual

JL Audio

JL Audio Stealthbox SB-J-UNLTD4DR/13TW5v2 User manual

JL Audio

JL Audio Stealthbox SB-GM-CFMINI/10W3v2 User manual

JL Audio

JL Audio 6W3v3-4 User manual

JL Audio

JL Audio JL AUDIO Evolution ZR800-CW User manual

JL Audio

JL Audio Stealthbox SB-F-EXPL3/10W3v3 User manual

JL Audio

JL Audio 12WOv3-4 User manual

JL Audio

JL Audio MX10IB3 User manual

JL Audio

JL Audio Stealthbox SB-T-TACDCG3/10TW3 User manual

JL Audio

JL Audio Stealthbox SB-H-RIDGLNE/10W3v3 User manual

JL Audio

JL Audio Stealthbox SB-F-F1502/10W3v3 User manual

JL Audio

JL Audio 300/2 User manual

JL Audio

JL Audio JL AUDIO 8W1v2-4 User manual

JL Audio

JL Audio MX101B3-SG User manual

JL Audio

JL Audio 13W1v2-4 User manual

JL Audio

JL Audio 12W3 User manual

JL Audio

JL Audio Stealthbox SB-N-350/10W3v2 User manual

JL Audio

JL Audio 15W5 Speci?cations User manual

JL Audio

JL Audio gotham v2 User manual

JL Audio

JL Audio Stealthbox SB-GM-SLVCRW/10W1v2 User manual

JL Audio

JL Audio 12W3v2 Series User manual

JL Audio

JL Audio Stealthbox SB-P-CYNNE/10W6v2/BK User manual

JL Audio

JL Audio Stealthbox SB-H-PIO1K/10TW3 User manual

Popular Subwoofer manuals by other brands

Sony

Sony XS-AW8 operating instructions

Sony

Sony XS-L836 Specifications

B&C Speakers

B&C Speakers 15 HPL 76W Specifications

Velodyne

Velodyne DD-18+ Specifications

Sonance

Sonance Cinema Series SUB 10-150 Specifications

Hifonics

Hifonics HW-12 Owners & installation manual

Magnat Audio

Magnat Audio ADR 130 BP user manual

Blitz

Blitz BZP106 Specifications

Technics

Technics SB-AS500 Operaing instructions

Lyngdorf

Lyngdorf BW-2 owner's manual

Lyngdorf

Lyngdorf BW-3 owner's manual

Pyle Pro

Pyle Pro PYLE PRO PDW15125 owner's manual

REL Acoustics

REL Acoustics Q Series operating instructions

Pioneer

Pioneer Elite S-W1EX Service manual

L-Acoustics

L-Acoustics KIVA SB15M Rigging manual

B&C Speakers

B&C Speakers Woofer 12 HPL 76 specification

KEF

KEF KUBE 200 installation manual

Yamaha

Yamaha SW500 owner's manual