JETWAY FFI02 Series User manual

Quick Installation Guide

NO. G03-FFI02QIG-F

Rev: 1.0

Release date: 2021-12-13

Notice:

The photos in this file are for illustration purpose only. The model may not be the latest version. Please

refer to the product you purchased for actual specification.

I. To Open the Chassis

1. Locate the screws in the spots marked on

the top cover of the system and unscrew

them one by one.

2. Turn over the bare bone system with the

heatsink upwards, as the photo shows.

3. Remove the screws in the marked spots on

the front panel.

4. Remove the screws in the marked spots on

the rear panel.

5. Remove the IO panels and lift the cover up

to open the chassis. For user to have a

clear view of layout, we may unplug some of

the cables during installation.

6. For CPU installation, user needs to remove

the screws on the marked spots to

dissemble the motherboard form chassis

cover.

Notice: 1. If the system is pre-installed with CPU heatsink, user needs to remove the screws on the

backside of the board to dissemble the heatsink before CPU installation; 2.Make sure that the cables are

plugged into their original places when necessary installation finished for the system to function normally.

II. To Install CPU

1. Find CPU socket on the board. Please make

sure that CPU socket is facing towards you

and the level is on you right hand side.

2. Remove the plastic protective cover from the

socket (Put it to the original place if CPU is

not installed. Do not touch the metal contact

pins of the CPU socket).

3. Press down the level and move it towards the

right side to free it from the hook.

4. Open the level upwards about 135 degree

and the metal protection plate will be pulled

up at the same time.

5. Make sure that Pin-1 Golden Finger Indicator in the place as shown in the above

photo and match the two alignment keys on the CPU with two points of the socket.

CPU can only be correctly installed in this direction. Incorrect installation might

cause damage to CPU.

6. Put down the load plate in the direction shown

above.

7. Press down the load level and move it

leftwards to make sure it is locked under the

notch.

Golden Finger

Indicator

Alignment Key

III.To Install Heatsink Thermal pads

1. Find the above CPU heatsink and CPU thermal pad package. Remove the protective films

on the both sides of the pad and apply it upon the bottom side of the heatsink for better heat

conduction.

2. Place the CPU heatsink upon the

installed CPU. The screw holes of the

heatsink should match corresponding

screw holes of the board. And then apply

corresponding thermal pad to the top

side of the heatsink as the photo shows.

3. Apply corresponding thermal pads to chipset

heat sink (HCS3XXHS2-F*2pcs). When

installation finished, tear off the protective film

from the pads before assembling the back cover

to the chassis.

Bottom Side

Paste Here!

Top Side

Paste Here!

Tear off the

Protective films

P/N:

HCS310HS1-F* 2pcs

60*52*1.0mm

4. Turn the board over and lock the heatsink to the board by tightening the screws (P/N: LCSC378M01-F*4)

on the marked spots.

5. Thermal pads need to be attached to the bottom of the motherboard, which will help the system to

dissipate heat (P/N: HCSHBFFHS1-1F*9).

*Note: There should be one more HCS310HS1-F / HCS3XXHS2-F / HCSHBFFHS1-1F left as spare parts

after normal assembly. User can use them to replace corresponding damaged thermal conductive pads.

Notice：Please restore the screws that lock the motherboard to the chassis cover when CPU & heatsink

installation completed. The cables unplugged during this process should be plugged to their original places

after heatsink installation.

IV. To Install SO-DIMM to the board

1. Find the SO-DIMM slot on the board.

2. Insert the gold-figure side of the compatible SO-DIMM into the slot at a 30 degree angle. See to it that the

break of the module fit into the notch of the slot.

3. Press down to secure the SO-DIMM to the slot. The eject tabs will lock automatically if installing direction

is correct.

V. To Install M.2 E-Key (2230) PCIe card

1. Locate the M.2. PCIe, type-2230 slot on

the board.

2. Remove the marked screw nut reserved

for M.2 PCIe card installation first.

3. Insert the gold-figure side of compatible card

into M.2. PCIe slot. See to it that the

golden-figure side is fully inserted into the slot.

4. Lock the card to the board by tightening up

the screw nut to the marked spot.

This manual suits for next models

Table of contents

Other JETWAY Computer Hardware manuals

JETWAY

JETWAY NF894V Series User manual

JETWAY

JETWAY FDF05 Operating and maintenance instructions

JETWAY

JETWAY LA20-10 Series User manual

JETWAY

JETWAY MI02 Series User manual

JETWAY

JETWAY JLI1BV-0L Series User manual

JETWAY

JETWAY MM02 Series User manual

JETWAY

JETWAY 694CS/VM4 User manual

JETWAY

JETWAY G03-BFDADN1QIG-F Operating and maintenance instructions

JETWAY

JETWAY LI1B Series User manual

JETWAY

JETWAY FDF10 Operating and maintenance instructions

JETWAY

JETWAY NC9T User manual

JETWAY

JETWAY JNLH61S-6C Series User manual

JETWAY

JETWAY I848ASR1A User manual

JETWAY

JETWAY MI225 Series User manual

JETWAY

JETWAY MM21 Series User manual

JETWAY

JETWAY NF631 Series User manual

JETWAY

JETWAY MI09-30 Series User manual

JETWAY

JETWAY HBJC924R3288DG2NS Series User manual

JETWAY

JETWAY MI24 Series User manual

JETWAY

JETWAY G03-NU93-F User manual

JETWAY

JETWAY LI22 Series User manual

JETWAY

JETWAY NF835V Series User manual

JETWAY

JETWAY MF04 Series User manual

JETWAY

JETWAY LI1BV Series User manual

Popular Computer Hardware manuals by other brands

EMC2

EMC2 VNX Series Hardware Information Guide

Panasonic

Panasonic DV0PM20105 Operation manual

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 user manual

Gigabyte

Gigabyte B660M DS3H AX DDR4 user manual

Raidon

Raidon iT2300 Quick installation guide

National Instruments

National Instruments PXI-8186 user manual

Hauppauge

Hauppauge WinTV-HVR-2250 Quick installation guide

Kontron

Kontron CP6002 user guide

Manhattan

Manhattan 702843 user manual

Aphex

Aphex 230 instruction manual

AMD

AMD Phenom II Product data sheet

Intel

Intel NUC 12 Pro user guide

dbx

dbx Zone Pro 1260 user manual

Galaxy

Galaxy GHDX2-2430S-24F4D Installation and hardware reference manual

Intel

Intel AXXRMFBU4 Quick installation user's guide

Kontron

Kontron DIMM-PC/MD product manual

ST X-NUCLEO-SAFEA1B How to use

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 installation manual