Jetson AMBER Volt TBH User manual
Volt
LED Strip Lights.
A guide for your lights.
IMPORTANT: READ CAREFULLY, RETAIN FOR FUTURE REFERENCE.
MODEL: TBH
Designed in Brooklyn | Made in China
Table of Contents
.............................................................
...........................................................
.........................
.....................................
.........................................
...............................................
Safety Warnings
Specs & Features
Preinstallation & Installing Your Lights
Controlling with the Controller
Controlling with the Remote
Controlling with the App
2
Safety Warnings
• Keep these instructions.
• Non-user replaceable light sources.
• Uncoil the light strip before use.
• Do not drop, puncture, open, cut, or disassemble this product.
• Do not install this product in any way other than what is outlined in
this guide.
• Do not place this device on hot surfaces.
• Only use the adaptor supplied; using a dierent adaptor can damage
the device.
• Do not submerge the strip or the power supply unit in water.
• Avoid long exposure to direct sunlight, which may cause damage.
• Do not use this product in small, enclosed locations that could limit
the low of air or trap excess heat.
• Do not expose this product to open lames or use near ire.
• Do not use the product in a strong magnetic ield.
• Do not use this product for emergency lighting/exits.
• Do not allow small children to operate, modify, or install this
device unsupervised.
• Use a clean, soft cloth to clean - do not use any cleaning agents
to clean.
• Manage in accordance with disposal laws in your area.
• Do not clean the device when it is on and connected to the
power supply.
• Do not connect the light strip to the power supply while in its
packaging or wound onto its reel.
• Do not use the rope light when covered or recessed into
a lat surface.
• Not intended for illumination; only use for ambience.
California Proposition 65
WARNING:
This product can expose you to a chemical such as Cadmium that is
known to the state of California to cause cancer or birth defects or
other reproductive harm. For more information go to
www.p65warnings.ca.gov/product
3
NOTICE OF COMPLIANCE
Changes or modiications not expressly approved by Jetson could
void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20 cm between the radiator &
your body.
LIMITED 1 YEAR WARRANTY
Limited 1 Year Warranty only applies to the manufacturer defects.
Contact Jetson Customer Care for detailed information via support.
ridejetson.com
Limited 1 Year Warranty does NOT cover:
• Normal wear and tear
• Improper assembly
• Corrosion
• Improper maintenance
• Installation of components, parts, or accessories not originally
intended for or compatible with the product as sold
• Damage or failure due to accident, misuse, abuse, or neglect
• Labor charges for part replacement or changeover
• Non-proprietary products (any other original part or component)
covered by the original manufacturer’s warranty
• Any accessories
4
Specs & Features
• POWER SUPPLY: 12V AC ADAPTER
• OUTPUT POWER: 16FT=12W, 32FT=24W 64FT=36W
• OPERATING TEMPERATURE: BETWEEN 4F AND 113F
• REMOTE CONTROL RANGE: UP TO 26FT
• REMOTE CONTROL BATTERY: CR2025 OR EQUIVALENT
• IP20 NON WATER RESISTANT FOR INDOOR USE ONLY
What’s in the Box
1. LED STRIP LIGHTS
2. REMOTE
3. CONTROLLER
4. AC ADAPTER
5. MOUNTING ADHESIVE
AC ADAPTER
CONTROLLER
5
1. Get Started
1.1 Preinstallation
1.2 Installing Your Lights
•CHECK THAT YOU HAVE EVERYTHING. BOX SHOULD CONTAIN
AMBER VOLT STRIP, CONTROLLER, AC ADAPTER, REMOTE
CONTROL AND MOUNTING ADHESIVE.
• WIPE DOWN AND CLEAN THE SURFACE YOU’RE PLANNING TO
PLACE YOUR LIGHTS ON.
• PEEL OFF THE PROTECTIVE TAPE ON THE BACK OF THE LIGHTS.
• PLACE LIGHTS ONTO SURFACE. PRESS DOWN TO MAKE SURE
ADHESIVE IS FIRMLY SECURED TO SURFACE.
• INSERT THE CONTROLLER INTO THE LIGHTS. ENSURE THAT
ARROWS LINE UP CORRECTLY.
• INSERT THE AC ADAPTER INTO THE CONTROLLER.
• PLACE POWER ADAPTER INTO ELECTRICAL OUTLET.
6
2.1 Controlling with the Controller
MUSIC MODE
ONOFF
CHANGE COLOR
ONOFF
2. How To Control Your Lights
IR RECEPTOR
7
2.2 Controlling with the Remote
•CONTROL AND CUSTOMIZE YOUR AMBER LIGHTS USING
THE INCLUDED REMOTE.
STATIC COLOR
DIY
NIGHT MODE
STARRY MODE
ONOFF BUTTONBRIGHTNESS + -
MUSIC MODE
TIMER
SPEED +
SPEED -
PARTY MODE
MOVIE MODE
8
CREATING CUSTOM COLORS:
1. PRESS EITHER THE ‘DIY1’, ‘DIY2’, OR ‘DIY3’ BUTTONS.
2. PRESS THE ‘DOWN’ BUTTON IN EITHER RED, GREEN, OR
BLUE TO CHANGE THE LED LIGHTS FROM THE DEFAULT
COLOR WHITE.
3. CONTINUE TO ADJUST EITHER RED, GREEN, OR BLUE BY
PRESSING THE ‘UP’ OR ‘DOWN’ BUTTONS UNTIL YOU REACH
YOUR PREFERRED COLOR.
4. PRESS THE SAME ‘DIY’ BUTTON THAT YOU DID IN STEP 1.
YOUR COLOR IS NOW SAVED, AND CAN BE RETRIEVED BY
PRESSING THE SAME ‘DIY’ BUTTON AT ANY TIME.
NOTE: YOU CAN NOW USE ADDITIONAL EFFECTS BUTTONS,
SUCH AS ‘FADE’. TO RETURN YOUR PREFERRED COLOR
WITHOUT THESE FUNCTIONS, PRESS THE RELEVANT
‘DIY’ BUTTON.
Table of contents
Other Jetson Lighting Equipment manuals
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
