JDS Uniphase TestifierPRO User manual
TestifierPROf Test Set
User's Guide
www.jdsu.com/hbn
a
2007 JDSU.All rights reserved.
Power
Button
Setup
Up Button
Telco Mode Button
Coax Mode Button
LCD
Screen Network
Mode Button
Down
Button
Select
Button
Remote
Data Jack
Telephone
Jack
Telephone
Jack
Data Jack F-Connector
Jack (Coax)
Table of Contents
Features............................................... 1
Description.......................................... 3
Instructions for Use.......................... 17
Cable Testing ������������������������������� 17
To Map Cable ID’s������������������������ 20
To Place Tone on a Cable ����������� 20
To Measure Length ���������������������� 21
To Perform Hub Blink ������������������ 23
Interpreting cable Test
Results............................................... 24
Battery Replacement........................ 29
Specications .................................. 30
Accessories .................................. 32
Warranty ............................................ 33
Shipping ��������������������������������������� 35
Support Service ��������������������������� 35
1
Warning!
Do not attach to energized cables� The
TestierPROfmay be damaged�
Caution!
Improperly crimped, damaged or un-
crimped plugs can damage the jacks
on the TestierPROf. Inspect plugs for
proper termination and crimping before
inserting into the TestierPROf. A
Sacricial Cable (TP74) can be used to
extend the life of the RJ45 jack of the
TestierPROf. Contacts should always
be recessed into the plastic grooves of
the plug.
Features
•Two-line by 16-character full
alphanumeric LCD with icons for clear
results
•Designed to test network (8-wire),
telephone (6-wire) and coax cabling
systems
•Separate Telco, Coax and Network
mode buttons allow for easy test
selection
•Built-in jacks and F-connector for
Telco, Network and Coax connections
•Cable test results displayed in wire
map format along with messages for
shorts and split pairs
2
•Integrated remote bay for easy storage
of the modular test remote
•Tests for shorts, opens, miswires,
reversals and split pairs when the test
remote is connected
•One-ended cable test for shorts, opens
and split pairs (when no remote is
connected)
•Displays PASS icon for correctly wired
T568A/B, both one-to-one & uplink
(cross-over) cables
•Displays PASS icon for correctly wired
6-pin telephone cables both straight-
through & reversed
•Map ID feature provides a cost
effective way to identify (ID) up to 20
cable runs at a time�
•Length measurement in feet or meters
using patented cable capacitance
method
•Tone generator mode for use with tone
tracers sends 4 user-selectable tones
on all pin/pair combos
•Hub blink mode sends link pulses to
network switch to blink port LED and
identify port
•Auto-off and timed backlight in any
mode for low power consumption and
long battery life
3
Description
TheTestierPROfis designed to test
all common low-voltage cabling systems
found in today’s automated homes,
telephone, network or video� It has
an LCD display and eight momentary
buttons. The TestierPROfhas three
modes of operation (Telco, Coax and
Network), each with a dedicated button
for easy test selection� In addition, a
Setup key is provided to allow for easy
access and selection of user-settable
options� The main unit comes with
built-in jacks and F-connector for Telco,
Network and Coax cables� It has an
integrated remote bay that houses a
detachable test remote for patch cable
testing� The test remote has built-in
jacks for Telco and Network cables�
The TestierPROfcan be turned on
by pressing the Power button or any of
the three mode buttons� At power up,
the TestierPROfreturns to the same
menu item or execution mode right
before it was last turned off� This allows
the user to power off and on the unit
within a long task without re-conguring
the unit every time it has been turned
off. When the TestierPROfis turned
on for the rst time after a new battery
is installed, the unit is initialized to the
4
default menu item Telco Cable Test�
Pressing the mode button repeatedly
cycles through all the menu items
available for that mode:
While the unit is on, pressing any of
the three mode buttons (Telco, Coax
or Network) brings up the same menu
item previously selected for that mode�
Pressing the Power button momentarily
(for less than 2 seconds) toggles the EL
backlight� Pressing the Power button for
more than 2 seconds turns off the unit�
When the unit is off, pressing the Power
button turns on the unit� While the unit
is off, holding down the SETUP key and
then pressing the Network button starts
the unit in Diagnostic mode�
Telco
Mode
Coax
Mode
Network
Mode
Cable
Test p
p
p
Map ID p p
Length p p p
Tone p p p
Hub
Blink p
5
Key Description:
Key
Feature Description
Telco mode button
Coax mode button
Network mode button
Up and down buttons
SEL
Select button
SETUP
Setup mode button
Power button
6
CableTest/Pretest – This mode
performs detailed analysis on a cable�
If a remote is sensed at the remote end
of the cable, a wire map, the remote ID
and certain faults are displayed at the
end of the cable analysis:
• There are two lines of numbers
displayed at the end of the test� The
top line of numbers on the display
represents the connector pins on
the main unit� The second line of
pin numbers is the connector pin
numbers of the remote, normally
being the same as the top line for a
normal (straight-thru) data cable�
• If there is a miswire, the numbers
on the second line indicate the pin
numbers detected�
• If no connection is detected for
some of the pins, the second line
will be blank in those pin locations�
• If a short is detected, the second
line will have a ashing ‘X’ in that
position and the specic short
condition displayed on the third line�
• If a high-resistance fault (i�e� a “soft”
short, as opposed to a hard short,
of up to 125 kohm for Network and
100 kohm for Telco) is detected, the
second line will have a ashing ‘R’
Table of contents
Other JDS Uniphase Test Equipment manuals
JDS Uniphase
JDS Uniphase Network Device JDSU User manual
JDS Uniphase
JDS Uniphase OneExpert DSL User manual
JDS Uniphase
JDS Uniphase ONT-601 MTM User manual
JDS Uniphase
JDS Uniphase IP Video Test Option HST-3000 User manual
JDS Uniphase
JDS Uniphase OTU-8000 User manual
JDS Uniphase
JDS Uniphase T-BERD MTS 5800 Series Parts list manual
JDS Uniphase
JDS Uniphase OTU-8000 (EOTU8000E) User manual
JDS Uniphase
JDS Uniphase 40 G Transport Module T-BERD/MTS-8000 User manual
JDS Uniphase
JDS Uniphase T-BERD User manual
JDS Uniphase
JDS Uniphase T-BERD 6000A User manual
JDS Uniphase
JDS Uniphase FFL-050 User manual
JDS Uniphase
JDS Uniphase IP Video Test Option HST-3000 User manual
JDS Uniphase
JDS Uniphase IP Video Test Option HST-3000 User manual
JDS Uniphase
JDS Uniphase 4100 User manual
JDS Uniphase
JDS Uniphase Validator User manual
JDS Uniphase
JDS Uniphase IP Video Test Option HST-3000 User manual
JDS Uniphase
JDS Uniphase IP Video Test Option HST-3000 User manual
JDS Uniphase
JDS Uniphase Lil' Buttie User manual
JDS Uniphase
JDS Uniphase IP Video Test Option HST-3000 Parts list manual
JDS Uniphase
JDS Uniphase IP Video Test Option HST-3000 User manual
