jcb JCB-PP1050 Installation manual
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
Safety and operating manual
Power Planer
JCB-PP1050
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
WARNING! Read all safety
warnings and all instructions.
Failure to follow the warnings and
instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions
for future reference.
The term "power tool" in the
warnings refers to your electric
(corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well
lit.
Cluttered or dark areas invite
accidents.
b) Do not operate power tools in
explosive atmospheres, such as in
the presence of flammable liquids,
gases or dust.
Power tools create
sparks which may ignite the dust
or fumes.
c) Keep children and bystanders
away while operating a power tool.
Distractions can cause you to
lose control.
2. Electrical safety
a) Power tool plugs must match
the outlet. Never modify the plug
in any way. Do not use any adapter
plugs with grounded power tools.
Unmodified plugs and matching
outlets will reduce risk of electric
shock.
b) Avoid body contact with
grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of
electric shock if your body is
grounded.
c) Do not expose power tools
to rain or wet conditions.
Water
entering a power tool will increase
the risk of electric shock.
d) Do not abuse the cord. Never
use the cord for carrying, pulling
or unplugging the power tool.
Keep cord away from heat, oil,
sharp edges or moving parts.
Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool
outdoors, use an extension cord
suitable for outdoor use.
Use of
a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a
damp location is unavoidable, use
a residual current device (RCD)
protected supply.
Use of an RCD
reduces the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are
doing and use common sense
when operating a power tool. Do
not use a power tool while you
are tired or under the influence
of drugs, alcohol or medication.
GENERAL POWER TOOL SAFETY WARNINGS
ORIGINAL INSTRUCTIONS
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
A moment of inattention while
operating power tools may result
in serious personal injury.
b) Use personal protective
equipment. Always wear eye
protection.
Protective equipment
such as dust mask, non-skid
safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal
injuries.
c) Prevent unintentional starting.
Ensure the switch is in the off-
position before connecting to
power source and/or battery pack,
picking up or carrying the tool.
Carrying power tools with your
finger on the switch or energising
power tools that have the switch
on invites accidents.
d) Remove any adjusting key or
wrench before turning the power
tool on.
A wrench or a key left
attached to a rotating part of the
power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times.
This enables better control of
the power tool in unexpected
situations.
f) Dress properly. Do not wear
loose clothing or jewellery. Keep
your hair, clothing and gloves
away from moving parts.
Loose
clothes, jewellery or long hair can
be caught in moving parts.
g) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of dust collection can reduce
dust-related hazards.
4. Power tool use and care
a) Do not force the power tool.
Use the correct power tool for
your application.
The correct
power tool will do the job better
and safer at the rate for which it
was designed.
b) Do not use the power tool if
the switch does not turn it on and
off.
Any power tool that cannot
be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from
the power source and/or the
battery pack from the power tool
before making any adjustments,
changing accessories, or storing
power tools.
Such preventive
safety measures reduce the
risk of starting the power tool
accidentally.
d) Store idle power tools out of
the reach of children and do not
allow persons unfamiliar with the
power tool or these instructions
to operate the power tool.
Power
tools are dangerous in the hands
of untrained users.
e) Maintain power tools. Check
for misalignment or binding of
moving parts, breakage of parts
and any other condition that may
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
affect the power tool’s operation.
If damaged, have the power
tool repaired before use.
Many
accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and
clean.
Properly maintained cutting
tools with sharp cutting edges are
less likely to bind and are easier
to control.
g) Use the power tool,
accessories and tool bits
etc. in accordance with these
instructions, taking into account
the working conditions and the
work to be performed.
Use of the
power tool for operations different
from those intended could result
in a hazardous situation.
5. Service
a) Have your power tool serviced
by a qualified repair person using
only identical replacement parts.
This will ensure that the safety of
the power tool is maintained.
PLANER SAFETY
WARNINGS
1. Wait for the cutter to stop
before setting the tool down.
An exposed rotating cutter may
engage the surface leading to
possible loss of control and
serious injury.
Note The above warning applies
only to planers without an
automatic closing guard.
2. Hold the power tool by
insulated gripping surfaces only,
because the cutter may contact
its own cord.
Cutting a “live” wire
may make exposed metal parts
of the power tool “live” and could
give the operator an electric
shock.
3. Use clamps or another practical
way to secure and support the
workpiece to a stable platform.
Holding the work by your hand
or against the body leaves it
unstable and may lead to loss of
control.
ADDITIONAL SAFETY
RULES FOR PLANNER
1. Always wear a dust mask.
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
SYMBOLS
To reduce the risk of injury, user must read
instruction manual
Warning
Wear ear protection
Wear eye protection
Wear dust mask
Double insulation
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with
your local authorities or retailer for recycling
advice.
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
1. LOCK-OFF SWITCH
2. ON/OFF SWITCH
3. HAND GRIP AREA
4. DUST EXTRACTION OUTLET
5. BELT COVER
6. FASTENING BOLT
7. REBATE PARALLEL GUIDE
8. LOCKING SCREW
9. BASE PLATE
10. V-GROOVES
11. REBATE DEPTH GAUGE
12. CUTTING DEPTH ADJUSTMENT
13. BLADE (See D1)
14. BLADE CLAMP (See D1)
15. SPANNER (See D1)
16. LARGE PULLEY (See E)
17. PINION (See E)
18. DUST COVER
COMPONENT LIST
*Not all the accessories illustrated or described are included in standard delivery.
91011
4
6
12
18
1 2 3
5
6
7
8
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
TECHNICAL DATA
Voltage 230-240V~50Hz
Power input 1050W
No load speed 16000/min
Protection class /II
Planing depth 0-4mm
Rebate capacity 0-14mm
Planing width 82mm
Machine weight 3.9Kg
NOISE INFORMATION
VIBRATION INFORMATION
Vibration total values (triax vector sum) determined according to EN 60745:
Typical weighted vibration
Vibration emission value ah= 6,57m/s²
Uncertainty K =1.5m/s²
A weighted sound pressure LpA:87dB(A)
A weighted sound power LwA : 98dB(A)
KpA & KwA= 3.0dB(A)
Wear ear protection when sound pressure is over: 80dB(A)
WARNING: The vibration emission value during actual use of the power tool can
differ from the declared value depending on the ways in which the tool is used
dependant on the following examples and other variations on how the tool is used:
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained.
The use the correct accessory for the tool and ensuring it is sharp and in good condition.
The tightness of the grip on the handles and if any anti vibration accessories are used.
And the tool is being used as intended by its design and these instructions.
This tool may cause hand-arm vibration syndrome if its use is not adequately
managed.
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
WARNING: To be accurate, an estimation of exposure level in the actual conditions
of use should also take account of all parts of the operating cycle such as the times
when the tool is switched off and when it is running idle but not actually doing the job. This
may significantly reduce the exposure level over the total working period.
Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades.
Maintain this tool in accordance with these instructions and keep well lubricated (where
appropriate).
If the tool is to be used regularly then invest in anti vibration accessories.
Avoid using tools in temperatures of 10oC or less.
Plan your work schedule to spread any high vibration tool use across a number of
days.
ACCESSORIES
We recommend that you purchase your accessories from the same store that
sold you the tool. Use good quality accessories marked with a well-known brand
name. Choose the type according to the work you intend to undertake. Refer to the
accessory packaging for further details. Store personnel can assist you and offer
advice.
Pair spare planer blades 2
Parallel guide 1
Rebate guide 1
Spanner 1
Dust bag 1
Dust cover 1
JCB, SO53 3LE
www.JCBDIY.com
Customer Helpline 0333 0143092
NOTE: Before using the tool,
read the safety and operating
manual carefully.
INTENDED USE
The machine is intended for
planing of firmly supported wooden
materials, such as beams and
boards. It is also suitable for
beveling edges and rebating.
1. SAFETY ON/OFF
SWITCH
The switch is locked off to prevent
accidental starting. Depress the lock
off button (1) then on/off switch (2)
and release lock off button (1). The
machine is working now. To switch
off, just release the on/off switch.
(See A)
2. CUTTING DEPTH
ADJUSTMENT
Smaller cutting depth of 0-1mm
(Max. 4.0mm) is best for most
surface planing or rebating. Rotate
the cutting depth adjustment (12) to
set the required cutting depth on the
scale ,Scale graduation = 0.1mm.
The clockwise rotation increases the
planing depth; the counterclockwise
rotation reduces the planing depth.
(See B)
OPERATING INSTRUCTIONS
A
B 12
Table of contents
Popular Planer manuals by other brands
Felisatti
Felisatti PF180/1500 operating instructions
DeWalt
DeWalt DW 1150 Operation, adjustmants, maintenance, spare parts
Triton
Triton TRP UL Operating and safety instructions
Melbourne
Melbourne MTC-49407 owner's manual
VARO
VARO POWERplus POW1520 manual
Powermatic
Powermatic 209 Operating instructions and parts manual
