JASION EB7 User manual
COPYRIGHT©2021 JASION. ALL RIGHTS RESERVED.
Visit www.jasionride.com to download the latest user manual.
User Manual
EB7
Home Page
Warning Message
Package Contents
Product Overview
Assembly
Start-up Procedure
Charge Your E-Bike
FAQS
Limited Warranty
Contact Us
01
02
03
04
05
06
16
17
18
19
21
32
33
34
35
38
This user manual will help you assemble
and operate your new electric bike. Be
this manual before riding.
NOTE TO ALL RIDERS UNDER 18 YEARS
OF AGE: It's very important that you get
parental permission before riding your
electric bike.
2
1
(We don't have a backup key).
Always wear a helmet when riding your electric bike.
Always respect pedestrians.
warranty.
Warning Message
Avoid water - The electric bike is not waterproof. The electronics may be damaged due to
dangerous and may result in injury.
Avoid prolonged exposure to sun or rain and avoid storage in places with high temperatures
or corrosive gas.
Abuse - We do not cover physical damage due to negligent care and extreme riding.
Whenever you ride
Do not modify the product from manufacturer’s original design.
Do not exceed
Avoid touching the charging port directly and do not let it make contact with a metal object.
Keep hands and all body parts away
Before riding -
correctly before each use.
Before riding -
to check that all safety labels are in place and you understand the safety warnings.
Before riding -
Before riding -
Never exceed
The electric bike should never be used by children under the age of 18.
Maximum Speed - Your electric bike goes at a maximum speed of 20 mph.
riding an electric bike. It is recommended that you contact an insurance company or broker for
To conserve electricity,
17.
16.
15.
14.
13.
12.
11.
10.
9.
5.
4.
3.
2.
1.
6.
7.
8.
3
Package Contents
1×User Manual 2×Pedals 1×Front Wheel1×Seat
the handlebar)
1xUSB Cable for Tail Light 2×Front Wheel Bearing
Nut Covers
1×Charger
2×Wrenches
1×Electric Bike
1xHeadlight 1xHeadset Cover 1xFront Fork1xHeadset Ring 1xStem
4
LCD Display
Stem
Headlight
Product Overview
Grip
Horn Switch
LCD Display
Derailleur
Saddle
Tail Light
Suspension Front
Disc Brake
TirePedals
Crankset
Wheel Chain
Motor
Seat Post
Headlight Switch
Display Controls
Assembly
1. Locate the front fork. Take out the
screw on the top of the front fork.
3. Install the headset ring. 4. Install the headset cover.
2. Insert the front fork into the front frame.
1 2
3 4
6
5
Assembly
1. Locate the stem and insert the
front fork into the stem.
3. Fold the handlebar perpendicular
to the ground.
4. Insert the screw into the nut. Twist
2. Unlock and pull up the latch on the
folding mechanism.
1 2
3 4
Assembly
5. Insert the handlebar into the
stem.
7. Tighten the screw again.
and right.
6. Make sure the LCD display and logo are
align with the center of the front fork. Note:
The folding latch is not in the center.
5 6
7 8
78
Assembly
4. Install the front wheel bearing nut covers.
3. Tighten the nut on the fork with wrench.
front wheel to align the axle at the center of the
wheel with the center of front dropout.
Note:
nut should be fully and properly secured. Ensure the front wheel
are properly secured before moving on to the next step.
1 2
3 4
1. Locate the disk brake. Remove the two screws.
the brake pads in the brake caliper.
4.Hold the cable to the frame with the clip.
2.Clamp the rotor between the two brake blocks.
Assembly
Note:
10
9
arch and set aside.
partway.
4. Plug in the headlight. Locate the two sides of the
and thread the locknut onto the bolt end.
Assembly Assembly
the pedal. Your leg should be almost fully extended(not lockedout) with a slight bend at the knee.
Move the seat up and down by sliding the seatpost
in or out of the seat tube. DO NOT raise the seatpost
the seatpost tube.
lever open and outward fully.
Adujst the seat and the head of the seat is
parallel with the top tube.
11 12
(1)
(2)
are properly secured and undamaged. Check that they are correctly secured before
Assembly
NOTICE: Ensure the seatpost and seat are
properly adjusted before riding. DO NOT
raise the seatpost beyond the minimum
tube (as shown at right). If the seatpost
projects from the frame beyond these
rider to lose control and fall. Ensure the
are inside the seat tube of the frame.
The suspension fork can move up and down up to 80mm to
cushion bumps in the riding sur which can make riding
on a rough road or trail smoother and more comfortable.
Depending on a rider’s preferencethe suspension fork can
be locked out as a rigid forkwhich will typically yield higher
ncy while pedaling.
The lockout lever (1) located on top of the right side of
the suspension focan be turned counterclockwise un
it stops to completely lock out the suspension fork’s travel.
To unlock the lockout leverturn the knob clockwise un
stops. When the lockout lever is unlockedresistance can
be adjusted by turning.
Assembly
1
13 14
√×
Assembly
by allen wrench.
Check the chain alignment. Rotate the right pedal and
crank toward the back of the bike as though pedaling
backward. Watch the chain and ensure the chain runs
around the front chainring) smoothly.
Note: If the pedal/ chain doesn't run smoothly or something seems misaligned, please contact Jasion Support Team.
B Key P
and key cannot be removed.
before moving or riding the bike.
can't be removed.
1
2
3
1
2
3
I
G
N
I
T
I
O
N
P
U
S
H
15 16
Table of contents
Other JASION Bicycle manuals
