Janome 9200D User manual
INSTRUCTION BOOK
MANUAL DE INSTRUCCIONES
LIVRET D’INSTRUCTIONS
MODEL
MODELO
MODÈLE 9200D
1
IMPORTANT SAFETY
INSTRUCTIONS
Your sewing machine is designed and constructed only for HOUSEHOLD use.
Read all Instructions before using this appliance.
DANGER– To reduce the risk of electric shock:
1. An appliance should never be left unattended when plugged in. Always unplug this appliance from the
electrical outlet immediately after using and before cleaning.
2. Always unplug before relamping. Replace bulb with same type rated 15 Watts.
3. Do not reach for the appliance that has fallen into water. Unplug immediately.
4. Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop
into water or other liquid.
WARNING – To reduce the risk of burns, fire, electric shock,or injury to persons.
1. Do not allow to be used as a toy. Close attention is necessary when this appliance is used by or near
children.
2. Use this appliance only for its intended use as described in this manual.
Use only attachments recommended by the manufacturer as contained in this manual.
3. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return the appliance to the nearest authorized dealer or
service center for examination, repair, electrical or mechanical adjustment.
4. Never operate the appliance with any air opening blocked. Keep ventilation openings of the sewing
machine and foot controller free from accumulation of lint, dust, and loose cloth.
5. Never drop or insert any object into any opening.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8. To disconnect, turn all controls to the off (“ 0 ”) position, then remove plug from outlet.
9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
10. Keep fingers away from all moving parts. Special care is required around the sewing machine needle
and knives.
11. Always use the proper needle plate. The wrong plate can cause the needle to break.
12. Do not use bent needles.
13. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.
14. Switch the sewing machine off (“ 0 ”) when making any adjustment in the needle area, such as
threading needle, changing needle, threading loopers, or changing presser foot, and the like.
15. Always unplug the sewing machine from the electrical outlet when removing covers, lubricating, or when
making any other adjustments mentioned in the instruction manual.
SAVE THESE INSTRUCTIONS
“Please note that on disposal, this product must be safely recycled in
accordance with relevant National legislation relating to electrical/
electronic products. If in doubt please contact your retailer for guidance.”
(European Union only)
Selon la législation nationale ce produit doit être recycl en toute sécurit
en accord avec les règles prévues pour les appareils électriques ou
électroniques.
En cas de doute contactez votre revendeur de machine coudre.
(union européenne seulement)
“Rogamos tenga en cuenta que para la destruccion y/o reciclado de este
producto debe seguir las normas de la legislacion nacional relativa a
productos electricos y/o electronicos. En caso de duda Pregunte a su
distribuidor”
(Sólo Unión Europea)
4
Do’s and Don’ts
1. Always be aware of the up-and-down movement of the needle and do not turn your attention
away from the machine while it is running.
2. When leaving the sewing machine unattended, the main switch of the machine must be
switched off or the plug must be removed from the socket-outlet.
3. When servicing the sewing machine, or when removing covers or changing lamps, the machine
must be disconnected from the power supply by removing the plug from the socket-outlet.
4. Do not place anything on the foot control, otherwise the machine will start inadvertently, or the
control or motor may burn out.
5. The maximum permissible power for the sewing lamp bulb is 15 watts.
6. When using your sewing machine for the first time, place a piece of waste fabric under the
presser foot and run the machine without thread for a few minutes. Wipe away any oil which
may have appeared.
Ce qu’il faut faire et ne pas faire
1. Faire toujours attention au mouvement de va-et-vient de l’aiguille et faire très attention pendant la
couture.
2. Lorsque la machine à coudre est laissée sans surveillance, l’interrupteur principal de la machine doit
être éteint ou la prise doit être retirée du socle.
3. Lors de la réparation de la machine ou lors du retrait des couvercles ou du changement des
ampoules, la machine doit être débranchée du bloc d'alimentation en retirant la prise du socle.
4. Ne rien placer sur la pédale de contrôle, sinon la machine risque de coudre par mégarde ou la pédale
ou le moteur peuvent griller.
5. La puissance maximale permise pour l’ampoule de la machine à coudre est de 15 watts.
6. Lors des premiers usages de la machine à coudre, placer un vieux tissu sous le pied presseur et faire
marcher la machine sans fil pendant quelques minutes. Essuyer toute huile présente, s’il y a lieu.
Lo que debe y no debe hacer
1. Siempre esté atenta al movimiento sube y baja de la aguja y no deje de ponerle atención a la máquina
mientras está funcionando.
2. Cuando no esté atendiendo a la máquina, debe desconectar el interruptor de la máquina o desenchufarla
del tomacorriente.
3. Cuando esté dándole servicio a la máquina, o cuando retire las cubiertas o está cambiando las
bombillas, debe desconectar la máquina de la energía eléctrica sacando el enchufe del tomacorriente.
4. No coloque ningún objeto en el pedal de control, pues la máquina podría comenzar a funcionar
inadvertidamente, o el control o el motor podrán quemarse.
5. La bombilla de luz para coser no debe tener más de 15 vatios de energía.
6. Cuando use su máquina de coser por la primera vez, coloque un retazo de tela debajo del pie prensatela y
haga funcionar la máquina sin el hilo por unos minutos. Seque cualquier aceite que pueda haber escurrido.
5
PREPARATION
Names of Parts ................................................... 8
Standard Accessories ........................................ 8
Connecting the Machine to the Power Supply
..... 10
Controlling Sewing Speed ................................ 10
For Your Safety ................................................10
How to Turn the Handwheel ............................. 12
Opening and Closing the Side Cover ............... 12
Opening and Closing the Looper Cover ...........12
The Position of Thread Guide Bar .................... 14
Attaching the Spool Holder Cap and Net
............ 14
Changing Needle.............................................. 16
Raising or Lowering the Presser Foot .............. 16
Removing the Presser Foot ............................. 18
Attaching the Presser Foot ............................... 18
Adjustment of Foot Pressure ............................ 18
Adjustment of Stitch Length ............................. 20
Adjustment of Differential Feed Ratio .............. 20
To Deactivate the Upper Knife ......................... 22
To Activate the Upper Knife ............................. 22
Adjustment of Cutting Width............................. 24
Adjustment of Needle Plate Setting Knob ........ 26
Threading the Machine.............................. 28~46
• Threading the Lower Looper ..................... 30
• Threading the Upper Looper ..................... 36
• Threading the Needle on the Right ........... 40
• Threading the Needle on the Left .............. 44
TEST STITCHING
Starting Sewing ................................................48
Finishing Sewing .............................................. 48
Sewing Continuously ........................................ 48
How to use Guide Lines ................................... 48
Securing Ends ..................................................50
Thread Tension (4 threads) .............................. 52
Threading the Machine (3 threads) .................. 56
Thread Tension (3 threads) .............................. 58
Thread and Needle Chart .................................60
TABLE OF CONTENTS
ROLLED HEMMING, PICOT EDGING AND
NARROW HEMMING
Machine Setting and Thread, Fabric and
Range of the Tension Dial ................................ 62
Thread Tension ................................................66
For Better Results ............................................ 68
DECORATIVE OVEREDGING
Thread and Fabric ............................................ 70
Machine Setting................................................70
GATHERING
Thread and Fabric ............................................ 70
Machine Setting................................................70
PIN TUCKING
Thread and Fabric ............................................ 72
Machine Setting................................................72
Sewing ..............................................................72
CARE OF YOUR MACHINE
Replacing the Upper Knife ...............................74
Cleaning Upper Knife Area ..............................74
Replacing the Light Bulb .................................. 76
Cleaning the Feed Dog .................................... 76
Oiling the Machine............................................ 78
Carrying the Machine ....................................... 78
Troubleshooting................................................80
OPTIONAL PARTS ....................................... 84
8
Names of Parts
1 Left needle thread tension dial
2 Right needle thread tension dial
3 Upper looper thread tension dial
4 Lower looper thread tension dial
5 Side cover
6 Looper cover
7 Handwheel
8 Power switch
9 Machine socket
10 Differential feed dial
11 Stitch length dial
12 Spool stand
13 Spool holder
14 Spool pin
15 Thread guide bar
16 Thread guide
17 Pressure adjusting screw
18 Presser foot
19 Needle plate setting knob
20 Thread cutter
21 Presser foot lifter
22 Needle plate
23 Upper knife release knob
24 Cutting width adjusting dial
25 Upper looper
26 Lower looper
27 Upper knife
28 Lower knife
Standard Accessories
1 Screwdrivers
2 Tweezers
3 Set of needles
PREPARATION
123
1
17
215 16
14
13
12
11
10
9
8
7
5
3
46
20
21
22
23
24
19
18
27
28
25
26
10
Connecting the Machine to the Power Supply
Before connecting the machine to the power supply,
make sure the voltage and frequency shown on the
machine conform to your electrical power.
1. Turn off the power switch, and connect the
machine plug to the machine socket.
2. Connect the power supply plug to your power
supply.
3. Turn on the power switch.
Controlling Sewing Speed
Sewing speed can be varied by the speed controller.
The harder you press on the controller, the faster the
machine runs.
Step on the speed controller with the presser foot
lifter up, and practice controlling the speed.
For Your Safety:
*While in operation, always keep your eye on the
sewing area, and do not touch any moving parts
such as the thread take-up lever, loopers,
handwheel, needle or knives.
*Always disconnect the machine from the power
supply:
—when leaving the machine unattended.
— when attaching or removing parts.
— when threading or cleaning the machine.
*Do not place anything on the foot control, otherwise
the machine will start inadvertently.
1Power switch
2Machine plug
3Machine socket
4Power supply plug
5Power supply
6Speed controller
1Speed controller
5
43
2
1
1
6
2
1
3
1
12
How to Turn the Handwheel
Always turn the handwheel toward you (Counter-
clockwise).
1Handwheel
Opening and Closing the Side Cover
To open:
Push the side cover to the left.
To close:
Push the side cover to the right.
1Side cover
Opening and Closing the Looper Cover
To open: A
While pushing with the thumb to the right as far as it
will go, pull the looper cover toward you.
To close: B
Lift the looper cover and push it against the machine.
The looper cover snaps into its position
automatically.
1Looper cover
NOTE:
Always close both side cover and looper cover when
the machine is in use.
1
1
1
A
B
14
1. Pull the thread guide bar up as far as it will go.
2. Turn the thread guide bar so that the thread
guides are right above the spool pins.
The Position of Thread Guide Bar
1Thread guide bar
2Thread guide
3Stoppers
4Spool pin
Attaching the Spool Holder Cap and Net
1. When you use a small thread spool, pull out the
spool holder from the spool pin. Then place the
spool with its slit side up, and put the spool holder
cap on top of it.
2. If the thread slips down from the spool during
threading and/or sewing, put a net on the spool as
illustrated to prevent jamming.
*The spool holder cap and net are optional
accessories.
1Net
2Spool pin
1Spool holder
2Spool pin
3Spool holder cap
4Slit
1
2
3
4
13
4
2
1
2
1, 2
1
2
*Make sure to lock the thread guide of guide pole
in the correct position with the two stoppers.
16
Raising or Lowering the Presser Foot
By raising or lowering the presser foot lifter, the
presser foot goes up or down.
*While in operation, keep the presser foot lowered
except when threading the machine or test running
without threads.
Thread tension will be released when the presser
foot lifter is raised.
1Presser foot
2Presser foot lifter
Changing Needle
Turn off the power switch and unplug the machine.
Raise the needle to its highest position.
Then loosen the left or right needle clamp screw for the
needle you are going to remove.
1Needle clamp screw on the left
2Needle clamp screw on the right
*Use HA-1SP #14 Needle or #11.
To attach the needle on the right :
Insert a new needle into the needle clamp with the
flat side to the back until the top of the needle
touches the stopper pin, then tighten the needle
clamp screw on the right.
To attach the needle on the left :
Insert a new needle into the needle clamp with the
flat side to the back until the top of the needle
touches the edge of the needle bar, then tighten the
needle clamp screw on the left.
*When the needles are set correctly, the left
needle is higher than the right one.
*Do not use any needle which is bent or blunt.
1Needle clamp
2Needle
3Needle stopper pin
4Edge of needle bar
5Needle clamp screws
6Flat side to the back
1
2
1
2
4
3
4
5
6
1
2
*Use HA-1SP #14 Needle or #11.
6
Table of contents
Other Janome Sewing Machine manuals
Janome
Janome 525S - User manual
Janome
Janome Sewing Machine User manual
Janome
Janome MC 11000 - User manual
Janome
Janome S650 User manual
Janome
Janome MyLock 213 User manual
Janome
Janome Air Thread 2000D Professional Reference manual
Janome
Janome 13512 User manual
Janome
Janome Sewing Machine User manual
Janome
Janome QUILT MAKER PRO User manual
Janome
Janome Quilt Maker 15 User manual
Janome
Janome NH22 User manual
Janome
Janome MC 11000 - User manual
Janome
Janome YC-482J-EC User manual
Janome
Janome 1200D User manual
Janome
Janome JW7630 User manual
Janome
Janome MB-4S User manual
Janome
Janome E1019 Troubleshooting guide
Janome
Janome E1019 User manual
Janome
Janome HD3000 User manual
Janome
Janome MB-4 User manual
