Jamex 7110 User manual

MODEL 7110/7112MODEL 7110/7112

CARD READERCARD READER

for afor a

Make & ModelMake & Model

All of the information contained in this manual is the property of Jamex, Inc. This manual is providedAll of the information contained in this manual is the property of Jamex, Inc. This manual is provided

to purchasers and users of equipment sold by Jamex, Inc. in order to supply the technical informationto purchasers and users of equipment sold by Jamex, Inc. in order to supply the technical information

necessary to install, operate, and maintain that equipment. Permission is hereby granted tonecessary to install, operate, and maintain that equipment. Permission is hereby granted to

photocopy this manual if (a) both the original and the copies are used only in support of equipmentphotocopy this manual if (a) both the original and the copies are used only in support of equipment

sold by Jamex, Inc., and (b) if this notice is attached to each copy. No part of this document may besold by Jamex, Inc., and (b) if this notice is attached to each copy. No part of this document may be

reproduced by any means, other than as stated above, without the written permission of Jamex,reproduced by any means, other than as stated above, without the written permission of Jamex,

Inc.,2415 N. Triphammer Rd., Ithaca, NY 14850.Inc.,2415 N. Triphammer Rd., Ithaca, NY 14850.

Rev. January 2006Rev. January 2006

Jamex, Inc. - 2415 N. Triphammer Rd., Ithaca, NY 14850 - 800-289-6550Jamex, Inc. - 2415 N. Triphammer Rd., Ithaca, NY 14850 - 800-289-6550

www.jamexvending.comwww.jamexvending.com

TABLE OF CONTENTSTABLE OF CONTENTS

INTRODUCTIONINTRODUCTION

Equipment Features Page 2Page 2

Other Jamex Products

USER'S MANUALUSER'S MANUAL

Operating GuideOperating Guide Page 3-4Page 3-4

Power-up

Operation of the Vending System

Bypass Operation

Data ManagementData Management Page 5Page 5

Reading the Meters

INSTALLATION and SERVICE GUIDEINSTALLATION and SERVICE GUIDE

Installation & Set upInstallation & Set up Page 6Page 6

Unpacking the Vending System

Physical Mounting

Electrical Installation

Programming Your Jamex Model 7110Programming Your Jamex Model 7110 Page 6-8Page 6-8

Adjusting the Price Per Copy

Programming Value to Cards

MaintenanceMaintenance Page 9Page 9

Trouble-Shooting GuideTrouble-Shooting Guide Page 9Page 9

InstallationInstallation Page 10-11Page 10-11

Electrical Hook-up

Point-to-Point Wiring Diagram

INTRODUCTIONINTRODUCTION

Thank you for choosing a JamexJamex system for your vending needs. This manual provides instructions for operating

your Jamex Vending SystemJamex Vending System as well as technical information necessary to install and maintain the system. Please

keep this manual available and refer to it when calling for technical support.

Model 7110/7112 Stand Alone Card ReaderModel 7110/7112 Stand Alone Card Reader is one part of a complete system that facilitates vending through the

use of Stored-Value Cards rather than, or in addition to, the use of cash. The use of Stored-Value Cards can

increase security of your vended services by reducing the handling of cash. They may also add convenience for

patrons who prefer to carry one small card rather than a pocket full of cash for larger transactions.

In addition to the Stored-Value Cards, a complete Card Vending System includes the following four elements:

- A method of dispensing the Stored-Value Cards

- A control mechanism which reads the cards and enables the copier, computer printer,

fax machine, micro fiche reader, etc. ( Model 7110/7112 is a control mechanism)

- A method of encoding value, security information, and revenue tracking codes

onto the Stored-Value Cards

- A method of tracking revenue and accounting for vended services

For more information on Stored-Value Card Systems please contact your local business equipment dealer, or call

Jamex at 1-800-289-6550 or visit our webpage at www.jamexvending.com.

FEATURES OF YOUR MODEL 7110/7112FEATURES OF YOUR MODEL 7110/7112

Your Jamex Vending SystemJamex Vending System model 7110/7112 incorporates the following features:

!Accepts only exclusive proprietary cards, maintaining the high security of your system

!Programmable maximum card value of up to $999.999

!Price per copy is programmable in $.001 increments up to $99.999

!Up to four user groups (site codes)

!Bypass cards for staff and service use

!Full feature LCD display for card and bypass copies, and system accounting

!Exclusive management cards for setting prices and reading meters

!Mounting holes provided for secure installation

!Solid state copier interface with polarity - independent connections

ŽSturdy steel housing with beige textured powder-coat epoxy finish

ŽTwo year warranty with "overnight" shipment of warranty parts and toll free technical support

Extended features of the Model 7112:Extended features of the Model 7112:

!Ability to program value to cards using a Command Cash Card

!Dual price capabilities

The full family of Jamex products includes:The full family of Jamex products includes:

-single copy coin only vending systems

-multi copy coin only systems

-multi copy coin & bill vending systems

-"FAX ACCESS" for charging by the page for the use of a Fax Machine

-compatible mounting systems and stands

-print vending systems for computers and computer networks

-card systems: System 7000 Stored-Value magnetic stripe card systems

Jamex, “The Payment Method People”Jamex, “The Payment Method People”

Since 1981, JamexJamex has developed vending technology for a variety of applications. We look forward to

assisting people like you with ongoing innovations in revenue generation through vending.

Jamex is a manufacturer who believes in Service. Should you have any questions concerning your model

7110/7112 or other Jamex Vending SystemsJamex Vending Systems, please call your authorized JamexJamex dealer or JamexJamex

customer service at 1-800-289-6550, or visit our website at www.jamexvending.com.

OPERATING GUIDEOPERATING GUIDE

POWER - UPPOWER - UP

When first powered up, the LCD display on your 7110/7112 Jamex Vending SystemJamex Vending System will scroll the following

the prompt “Insert Your Card”

OPERATION OF THE JAMEX 7110/7112 VENDING SYSTEMOPERATION OF THE JAMEX 7110/7112 VENDING SYSTEM

JamexJamex CopyCards are required for the operation of your Stand Alone Card Reader. These cards are ordered from

JamexJamex and are formatted to work with the Jamex reader. Jamex Stored Valued Copy Cards are white with blue

graphics. Management Cards are blue with white graphics. On the face of these cards are the words ”Copy Card”,

the JamexJamex logo and a stylized blue arrow. On the back of the card is a magnetic stripe which stores the security

coding that designates your cards as specific to your location, and the stored value which allows the patron to buy

services.

These cards may also be coded to differentiate between four distinct groups of users. These user groups are

sometimes referred to as Site Codes. The activity for each Site Code is tracked separately in the accounting

function of your 7110/7112. When a copy card is inserted into the 7110/7112 Card Reader it will determine that the

card is acceptable to that reader, record the activity, and determine what price to charge and to deduct from the

value stored on the card for the service purchased. Stored Value Cards are programmed with a Site Code. The

Site Code programed to the Stored Value Card must match one of the four Site Codes programmed to the Card

Reader. This security feature ensures that the Vend System is proprietary.

Begin a transaction by inserting a Copy Card arrow end first and face up into the card reader. The display will show

the value stored on the card. When this value meets or exceeds the vend price, the copier (micro fiche reader, fax

machine, etc) will be enabled. Each time the copier makes one copy, the value stored on the card will be

decreased by the cost per copy and the display will show the remaining value left on the card. The copier will

remain enabled as long as the value stored on the card remains at or above the vend price. When the patron is

finished they may terminate the transaction by pressing the white “Card Return” button. The display will read “Wait”

for a few seconds. The card’s magnetic stripe will be encoded with any unused value and the card will be returned

to the exit position. The Display will read “Take Card” and the copier will be disabled.

CAUTION: It is very important not to interrupt the power source or to remove the copy card without firstCAUTION: It is very important not to interrupt the power source or to remove the copy card without first

pressing the white “Card Return” button. If either of these actions is attempted, the card will not be encodedpressing the white “Card Return” button. If either of these actions is attempted, the card will not be encoded

with any unused value and the card will no longer be useable.with any unused value and the card will no longer be useable.

BYPASS OPERATIONBYPASS OPERATION

Your JamexJamex model 7110/7112 Stand Alone Card Reader has a Bypass feature and has been shipped with a

Bypass Card to allow authorized personnel to make copies with no cost to themselves. To use the Bypass feature,

simply insert the blue Bypass Card into the reader, arrow first and face up. The display will read -BYPASS-. As

long as the card is in place copies may be made. When the user is finished they may press the white Card Return

button and reclaim the Bypass Card.

EXTENDED FEATURES OF THE MODEL 7112EXTENDED FEATURES OF THE MODEL 7112

Set Card Value CARDSSet Card Value CARDS

The Model 7112 has the capability of programming value to Stored Value Cards. This can be done with a Set Card

Value card, which is supplied with the 7112 Card Reader. For instructions on how to use a Set Card Value Card,

see page 8, Program Value to Cards section of this manual.

DUAL PRICINGDUAL PRICING

This feature allows for an alternate price to be charged for a different size of paper. This feature is dependent upon

the make and model copier being interfaced with the Model 7112.

WARNING: JAMEX COPY CARDS SHOULD NOT HAVE HOLES PUNCHED IN THE CARD. STICKERS ORWARNING: JAMEX COPY CARDS SHOULD NOT HAVE HOLES PUNCHED IN THE CARD. STICKERS OR

OTHER FOREIGN MATERIALS PLACED ON THE CARDS WILL ENDANGER THE OPERATION OF THEOTHER FOREIGN MATERIALS PLACED ON THE CARDS WILL ENDANGER THE OPERATION OF THE

READER. DO NO BEND THE CARD OR WRITE ON THE CARD SURFACE.READER. DO NO BEND THE CARD OR WRITE ON THE CARD SURFACE.

DATA MANAGEMENTDATA MANAGEMENT

READING THE METERSREADING THE METERS

The Jamex Vending SystemJamex Vending System 7110/7112 allows you to account for the use of the vended equipment by reading and

recording amounts shown on the display. To read the meters, insert the blue Read Meters card arrow first and face

up. The display will show “Meters..” for an instant and will return the card to the exit position. Leave the card in this

position as you record the information from the meters. The following chart explains the information which will flash

on the display. After you read and record each line, press the white button once to advance the display to the next

meter.

DISPLAYDISPLAY EXPLANATIONEXPLANATION

Meter A 1-----NUMBER The number of copies made using cards with site code 1

Meter A 2----NUMBER These meters will track copies made if there are site codes 2, 3, and

Meter A 3----NUMBER 4 to track different types of card users

Meter A 4----NUMBER

NOTENOTE: Meter B tracks the alternate priced copies made. This dual price capability is an extended feature of the Model 7112 and

is dependent on the copier to which it is being interfaced.

Meter B 1----NUMBER The number of alternate priced copies made using cards with site code 1

Meter B 2----NUMBER These meters will track alternate priced copies made, if there are site codes 2,3,

Meter B 3--------NUMBER and 4 to track different types of card users

Meter B 4----NUMBER

Bypass A 1----NUMBER The number of copies made that would have been charged to cards with

site code 1 except that they were made using a Bypass card.

Bypass A 2----NUMBER If there are additional site codes, the number of copies that would have

Bypass A 3----NUMBER been charged to cards with each site code but were made using a

Bypass A 4----NUMBER Bypass card will be displayed

NOTE:NOTE: Meter B tracks the alternate priced copies made. This dual price capability is an extended feature of the Model 7112 and

is dependent on the copier to which it is being interfaced.

Bypass B 1----NUMBER The number of alternate price copies made that would have been charged to

cards with site code 1 except that they were made using a Bypass card.

Bypass B 2----NUMBER If there are additional site codes, the number of alternate priced copies that Bypass

B 3----NUMBER would have been charged to cards with each site code but were made using a

Bypass B 4----NUMBER Bypass card will be displayed

Sales 1----$ VALUE The total dollar value of copies made using cards with site

code 1.

Sales 2----$ VALUE If there additional site codes, the total value of copies made

Sales 3----$ VALUE for each site code will be displayed.

Sales 4----$ VALUE

TotalCyc----NUMBER Total number times a card has been inserted and read.

ReadFail----NUMBER Total number of times a card was inserted and could not be

read.

This completes the meter readings. Remove the Read Meters card and the display will return to “Insert Your Card”.

INSTALLATION AND SET UPINSTALLATION AND SET UP

UNPACKING THE VENDING SYSTEMUNPACKING THE VENDING SYSTEM

The following equipment is included in your model 7110/7112 shipment:

- Model 7110/7112 vending unit, including cabling appropriate to the copy machine specified

on your purchase order and a power cable

- This Operation Manual & Installation and Service Guide

-Management Card Set - Read Meters Card, Set Prices Card, Bypass Card

The Model 7112 will also include Command Cash Card

PHYSICAL MOUNTINGPHYSICAL MOUNTING

Your Jamex Vending SystemJamex Vending System may be simply placed near the copier it will control or it may be bolted to a cabinet or

a table via the pre drilled mounting holes in the base of the unit.

ELECTRICAL INSTALLATIONELECTRICAL INSTALLATION

Please refer to the Point-to-Point Wiring Diagram and Step by Step Electrical Connection directions on the last two

pages of this manual.

PROGRAMMING YOUR JAMEX MODEL 7110/7112PROGRAMMING YOUR JAMEX MODEL 7110/7112

ADJUSTING THE PRICE PER COPYADJUSTING THE PRICE PER COPY

The blue Set Prices card allows you to adjust the prices charged for each site code that is programmed into your

Stand Alone Card Reader. This card also allows you to change the maximum value which may be read on any

card. The maximum card value is a safety function to limit the loss by any patron who may lose a card. Follow the

steps below to adjust Max Card Value and Prices.

Begin the process of setting prices by inserting the Set Prices card.

-the display will show “Prices..” for an instant and will return the card to the exit position.

-the display will begin flashing Max Card....ƒ025.000 (NOTE UP ARROW)

To increase the maximum value that may be read from a card press the white button on the front of the reader.

-the display will show an increased max card value of $.001 cent for each time the white button is

pressed.

If you press and hold the white button, the amount will continue to increase until you release the button.

This manual suits for next models

Table of contents

Jamex 7110 User manual

Popular Card Reader manuals by other brands