JAI GO-5000M-PGE User manual
Thank you for purchasing this product.
Be sure to read this documentation before use.
This documentation includes important safety precautions and instructions on how to operate the unit. Be sure to read this documentation to ensure
proper operation.
The contents of this documentation are subject to change without notice for the purpose of improvement.
© 2023 JAI
User Manual
GO-5000M-PGE
GO-5000M-PGE-UV
CMOS Digital Progressive Scan
Monochrome and Monochrome UV Camera with GigE Interface
Document Version: 2.0
GO-5000M-PGE_Manual_Ver.2.0_2023-04-26
GO-5000M-PGE | GO-5000M-PGE-UV | User Manual (Ver. 2.0) Table of Contents
- 2 -
Table of Contents
Table of Contents 2
About Technical Note 5
Notice/Warranty 6
Notice 6
Warranty 6
Certifications 6
CE Compliance 6
FCC 6
Warning 7
KC 7
Supplement 8
Usage Precautions 9
Notes on Cable Configurations 9
Notes on LAN Cable Connection 9
Notes on Attaching the Lens 9
Phenomena Specific to CMOS Image Sensors 10
Notes on Exportation 10
Features 11
Feature Overview 11
Parts Identification 13
①Lens Mount (C-Mount) 13
②RJ-45 Connector 13
③POWER/TRIG LED 15
④LINKLED 15
⑤ACTLED 15
⑥DC IN/TRIG Connector (6-Pin Round) 16
⑦Mounting Holes (M3, 3mm depth) 16
Preparation 17
Step 1: Install the Software (First Time Only) 18
Step 2: Connect Devices 18
GO-5000M-PGE | GO-5000M-PGE-UV | User Manual (Ver. 2.0) Table of Contents
- 3 -
①Lens 19
②Direct Mounting (or Use MP-43 Tripod AdapterPlate) 19
③LAN Cable 20
➃Network Card 20
⑤DC IN / Trigger IN Connection Cable 20
⑥AC Adapter (Power Supply) (If Necessary) 20
Step 3: Verify Camera Operation 21
Step 4: Verify the Connection between the Camera and PC 21
Step 5: Change the Camera Settings 24
Step 6: Adjust the Image Quality 25
Adjust the Gain 26
Adjust the Black Level 27
Step 7: Save the Settings 27
To Save User Settings 28
To Load User Settings 29
Main Functions 30
Digital IN/OUT Interface 30
GPIO IN/OUT Matrix 33
Optical Interface 34
Characteristics of Optical Interface 35
Opt In Filter Selector Function 36
Pulse Generator 36
Sensor Layout 42
Camera Output Format 43
Pixel Format 44
Output Timing (Horizontal) 45
Output Timing (Vertical) 46
ROI (Region of Interest) Settings 48
Digital Output Bit Allocation 48
Acquisition Control 49
Acquisition Mode 50
Acquisition Start 53
GO-5000M-PGE | GO-5000M-PGE-UV | User Manual (Ver. 2.0) Table of Contents
- 4 -
Acquisition Stop 53
Acquisition Frame Rate 53
Calculation of the Maximum Frame Rate 54
Exposure Mode 56
Trigger Control 58
Normal Continuous Operation 61
Timed Mode 62
Trigger Width Mode 63
RCT (Reset Continuous Trigger) Mode 64
Video Send Mode 65
Sequence Mode 66
Trigger Sequence Mode Basic Timing 67
Sequence Index Table (Default) 68
Descriptions of Index Table Parameters 69
Multi ROI Mode 70
Operation and Function Matrix 71
Black Level Control 72
Gain Control 73
LUT (Lookup Table) 75
Gamma 76
Blemish Compensation 77
ALC (Automatic Level Control) 77
HDR (High Dynamic Range) 78
Non-Volatile Flash Memory 79
Miscellaneous 80
External Appearance and Dimensions 80
Spectral Response 81
Specifications 82
User's Record 85
Revision History 86
GO-5000M-PGE | GO-5000M-PGE-UV | User Manual (Ver. 2.0) Table of Contents
- 5 -
About Technical Note
Some additional technical information is provided on the JAI website as Technical Notes. In this
manual, if a technical note is available for a particular topic, the above icon is shown. Please refer to
the following URL for Technical notes.
https://www.jai.com/support-software/technical-notes
GO-5000M-PGE | GO-5000M-PGE-UV | User Manual (Ver. 2.0) Notice/Warranty
- 6 -
Notice/Warranty
Notice
The material contained in this manual consists of information that is proprietary to JAI Ltd., Japan, and
may only be used by the purchasers of the product. JAI Ltd., Japan makes no warranty for the use of
its product and assumes no responsibility for any errors which may appear or for damages resulting
from the use of the information contained herein. JAI Ltd., Japan reserves the right to make changes
without notice.
Company and product names mentioned in this manual are trademarks or registered trademarks of
their respective owners.
Warranty
For information about the warranty, please contact your factory representative.
Certifications
CE Compliance
As defined by the Directive 2004/108/EC of the European Parliament and of the Council, EMC
(Electromagnetic compatibility), JAI Ltd., Japan declares that GO-5000M-PGE and GO-5000M-PGE-
UV comply with the following provisions applying to their standards.
EN 61000-6-3 (Generic emission standard part 1)
EN 61000-6-2 (Generic immunity standard part 1)
FCC
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
lReorient or relocate the receiving antenna.
lIncrease the separation between the equipment and receiver.
GO-5000M-PGE | GO-5000M-PGE-UV | User Manual (Ver. 2.0) Notice/Warranty
- 7 -
lConnect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
lConsult the dealer or an experienced radio/TV technician for help.
Warning
Changes or modifications to this unit not expressly approved by the party responsible for FCC
compliance could void the user’s authority to operate the equipment.
KC
제조년월은 제품상자의 라벨을 참조하십시오.
GO-5000M-PGE | GO-5000M-PGE-UV | User Manual (Ver. 2.0) Notice/Warranty
- 8 -
Supplement
The following statement is related to the regulation on “Measures for the Administration of the Control
of Pollution by Electronic Information Products “, known as “China RoHS“. The table shows contained
Hazardous Substances in this camera.
mark shows that the environment-friendly use period of contained Hazardous Substances is 15
years.
重 要 注 意 事 项
有毒，有害物质或元素名称及含量表
根据中华人民共和国信息产业部『电子信息产品污染控制管理办法』， 本产品《 有毒，有害物质或
元素名称及含量表》如下．
部件名称
有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr (VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
电路板 × 〇 〇 〇 〇 〇
螺丝 × 〇 〇 〇 〇 〇
插座 × 〇 〇 〇 〇 〇
..... ..... ..... ..... ..... ..... .....
〇:表示该有毒有害物质在该部件所有均质材料中的含量均在GB/T 26572-2011规定的限量要求以下。
×:表示该有毒有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572-2011规定的限量要求。
环保使用期限
电子信息产品中含有的有毒有害物质或元素在正常使用的条件下不会发生外 泄或突变、
电子信息产品用户使用该电子信息产品不会对环境造成严重污染 或对其人身、财产造成
严重损害的期限。
数字「15」为期限15年。
GO-5000M-PGE | GO-5000M-PGE-UV | User Manual (Ver. 2.0) Usage Precautions
- 9 -
Usage Precautions
Notes on Cable Configurations
The presence of lighting equipment and television receivers nearby may result in video noise. In such
cases, change the cable configurations or placement.
Notes on LAN Cable Connection
Secure the locking screws on the connector manually, and do not use
a driver. Do not secure the screws too tightly. Doing so may wear
down the screw threads on the camera. (Tightening torque: 0.147 Nm
or less)
Caution: Secure manually. Do not secure too tightly.
Notes on Attaching the Lens
How to Clean a Sensor
Avoiding Dust Particles
When attaching the lens to the camera, stray dust and other particles may adhere to the sensor
surface and rear surface of the lens. Be careful of the following when attaching the lens.
lWork in a clean environment.
lDo not remove the caps from the camera and lens until immediately before you attach the lens.
lTo prevent dust from adhering to surfaces, point the camera and lens downward and do not
allow the lens surface to come into contact with your hands or other objects.
lAlways use a blower brush to remove any dust that adheres.
lNever use your hands or cloth, blow with your mouth, or use other methods to remove dust.
GO-5000M-PGE | GO-5000M-PGE-UV | User Manual (Ver. 2.0) Usage Precautions
- 10 -
Phenomena Specific to CMOS Image Sensors
The following phenomena are known to occur on cameras equipped with CMOS image sensors.
These do not indicate malfunctions.
lAliasing: When shooting straight lines, stripes, and similar patterns, vertical aliasing (zigzag
distortion) may appear on the monitor.
lBlooming: When strong light enters the camera, some pixels on the CMOS image sensor may
receive much more light than they are designed to hold, causing the accumulated signal charge
to overflow into surrounding pixels. This “blooming” phenomenon can be seen in the image but
does not affect the operation of the camera.
lFixed pattern noise: When shooting dark objects in high-temperature conditions, fixed pattern
noise may occur throughout the entire video monitor screen.
lDefective pixels: Defective pixels (white and black pixels) of the CMOS image sensor are
minimized at the factory according to shipping standards. However, as this phenomenon can be
affected by the ambient temperature, camera settings (e.g., high sensitivity and long exposure),
and other factors, be sure to operate within the camera’s specified operating environment.
Notes on Exportation
When exporting this product, please follow the export regulations of your country or region.
Other manuals for GO-5000M-PGE
2
This manual suits for next models
1
Table of contents
Other JAI Machine Vision System manuals
JAI
JAI GO-5100MP-USB User manual
JAI
JAI GO-5000M-PGE-UV User manual
JAI
JAI GO-5000M-USB-UV User manual
JAI
JAI BM-500 GE User manual
JAI
JAI SW-4010Q-MCL-M52 User manual
JAI
JAI GO-5000M-PGE-1 User manual
JAI
JAI GO-2400M-PGE User manual
JAI
JAI GO-5000M-PMCL-UV User manual
JAI
JAI GO-5000M-USB-UV User manual
JAI
JAI GO-5000M-PGE-UV User manual
