Jaga COCOON User manual

CLICK

JAGAUK cocoon 03.03

INSTALLATION INSTRUCTIONS

COCOON

Contents:-

Chrome

blank plug

Air Vent

Screws

Washers

Rawl Plugs Always retain label

with element until installation

is complete. This will assist in

casing pack selection (see ﬁg. 6)

Number of brackets

required for casing

lengths:-

40cm to 120cm = 2

140cm to 220cm = 3

240cm to 300cm = 4

Cut away ends of shrink wrap, remove ﬁtting

kit and push ﬁt brackets onto end element plate.

Illustration shows brackets ﬁtted for right hand

connections.

Fit central

support feet

if unit is

140cm long

or above, see

instructions

packed with

feet.

H = 20.5cm (205mm)

from ﬁnished ﬂoor H = 20.5cm (205mm)

from ﬁnished ﬂoor

Offer up unit and mark wall ﬁxings,

positioning underside of heat exchanger

205mm above ﬁnished ﬂoor level

Number required for

casing lengths:-

40cm to 120cm = 0

140cm to 220cm = 1

240cm to 300cm = 2

FITTING PACK

POSITIONING DETAILS

RIGHT HAND CONNECTIONS LEFT HAND CONNECTIONS

HEATING ELEMENT FIXING BRACKETS CENTRAL SUPPORT

FEET

(Kit is located within shrink

wrap of element)

Fig. 1

Drill 8mm holes, ﬁt Rawl plugs

and screw unit to wall.

Fig. 4 Fit valves and connect pipe

work. Units can now be ﬁlled

and tested, but do not ﬁt TRV

head at this point.

If top valves are being used

refer to instructions packed

with valve kits.

Fig. 5

Each front panel is 10cm high.

4 bracket nibs = 40cm plus

20cm to ﬂoor = casing height

required 60cm (600mm)

Element Label L50, Type 10

Casing pack

required 60. 50. 10.

HLD

When ﬁxing and pipe work complete. Assemble casings as overleaf

Fig. 6

Fig. 2 Fig. 3

Alternatively,

if you need

left hand

connections –

turn bracket

through 180°

before clicking

onto heat

exchanger

205mm

Example. Casing pack selection.

INSTALLATION INSTRUCTIONS

COCOON CASING ASSEMBLY

See supplement sheet for 40cm length casings

Identiﬁcation e.g. 60. 50. 10

60cm high

50cm length

10cm depth (type)

Top grille

Top panel

(chamfered

top edge)

Front panel

Lay front grille ﬂat, ﬁns facing

downwards. Position a front plate either

side, position with notches at bottom. Clip together the three parts using front grille clips as

shown.

1. Press down centre of clip onto grille ensuring

tube grips locate correctly either side of grill tube.

2.3. then press ends of clip over lips of front panels

IMPORTANT! 40cm length casings use different style

of clip. See supplement sheet for ﬁgs 8 and 8A

Refer to section 8A for clip positions BEFORE assembly

Hang sub assembly

onto bottom nibs of

bracket.

Remember to remove

any remaining element

shrink wrap at this

point.

Assemble

remaining front

and top panels

Position each side

panel over the

lowest front panel

ensuring

protruding nib

hooks into notch.

Continue pressing

side panel

upwards until

your hear it

clearly snap into

place in the notch

in the top panel

Now ﬁt the grille. The

double fasteners on the

underside of the plastic

corner piece, must be

pressed over the side

panel until you hear it

click into the slots in

the side panel.

Fit Phillips screws and

tighten them.

TRV head should now

be ﬁtted together with

trims and blank plug.

Front grille clip

End panel blank plug

TRV aperture split rim

Top grille screw fasteners

Front grille

Side

Fig. 7 Fig. 8

Fig. 9

Fig. 11 Fig. 12

Fig. 10

CASING PACK CASING COMPONENTS FITTINGS

CLICK

Once the casing is correctly

assembled, it will remain in

one piece and can be removed

and reﬁtted as an assembly.

For further technical assistance telephone 01531 631533

Fig. 8A Grille clips must be ﬁtted in these positions.

View is from rear of grille when face down.

L.H. connections Casing Lengths R.H. connections

50cm

60cm

All longer lengths

on lengths

over 120cm

ﬁt a 3rd

centre clip

IMPORTANT: 40cm length casings use different grille clip see

supplimentary sheet.

Other Jaga Heater manuals

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide