Jadeim Handy 10740 User manual

AIR LIFT

INSTRUCTIONS

PARTS DRAWING

PARTS LIST

WARNING: READ INSTRUCTIONS BEFORE OPERATING

1. Center load on table - 1000 lb. maximum.

2. Connect to 100 psi maximum shop air.

3. Keep safety bar in position at all times - except

when lowering.

4. Keep hands and tools from under carriage.

5. Do not mount table when in elevated position.

6. Do not ride vehicle onto lift.

7. Lift must be in the lowered position when moving.

8. Only trained persons should operate Air Lift.

9. The working area should be sufficiently lit.

10. Foot controller should be at least 3 feet away from

Air Lift during raising and lowering operation.

11. Recommended for indoor use only.

HANDY INDUSTRIES DIVISION OF JADEIM, LLC 401 South 2nd. Marshalltown, IA 50158

1-800-247-7594 Fax 641-752-1205 www.handyindustries.com

Part Numbers 10740 - 16749 - 16600

LIFT TABLE

DETENT BAR

FOOT VALVE

RAMP

SAFETY LATCH

AIR LIFT

NOTE: READ ENTIRE MANUAL TO COMPLY WITH ALL SAFETY AND SERVICE PRECAUTIONS. DEATH, PERSONAL

INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY.

INSTRUCTIONS

UNPACKING AND SET-UP

1. Open carton, then remove ramp, and shipping boards.

2. CAREFULLY TURN TABLE UPRIGHT INTO OPERATING POSTION BEFORE REMOVING SHIPPING

CABLE RESTRAINT FROM SCISSOR MECHANISM.

3. Connect foot-operated air valve to 100 psi air supply. The lift may be damaged and/or personal injury may

result if the pressure exceeds the maximum 100 psi rating.

4. Stand clear of lift table and depress the UP side of foot valve to raise table.

5. To lower table, lift detent bar from safety latch and lower to next position or to floor.

6. Insert ramp mounting pins into holes at either end of table to mount ramp.

NOTE: If cycle vise is being installed, ramp must be mounted opposite the cycle vise.

OPERATION

1. Loads must be centered on table at all times.

2. Loads must be firmly positioned and secured on table at all times.

3. All moving parts have been lubricated at the factory and should be re-lubricated every 6 months to prevent

galling. Grease zerks are located at each end of frame pivot shaft and at top ends of inside frame assembly.

4. Lightly oil cylinder rod when it becomes dry.

5. Squirt some oil through air bleed hole in plate end of cylinder to lubricate piston and its seal every

6 months.

6. Pivot shaft set screws should be checked frequently to be sure they are tight. These are located at the top

end of the inside frame assembly.

OTHER OPTIONS AVAILABLE

Separate installation instructions included with each option.

PART #

DESCRIPTION

14476

CV-17 CYCLE VISE – Vise with removable wheel stop built into vise

10730

8” SIDE EXTENSIONS (2) – Expands width of lift from 24” to 40”

10728

12” SIDE EXTENSIONS (2) – Expands width of lift from 24” to 48” includes stabilizer bar

16011

13” FRONT EXTENSIONS – Extends lift top to 93” for longer wheel base motorcycles

15566

RAMP END EXTENSION – Attaches to end of lift ramp for a more gradual incline to prevent bigger

bikes from dragging bottom.

10737

SNOWMOBILE WING KIT – Used when lifting snowmobiles

14169

TRIKE EXTENSION – Used for 3 wheeled vehicles

16355

CE FOOT PEDAL – Covered foot pedal

10732

LIFT DOLLY – Helps move lift while in down position

15833

RED HANDY TIE-DOWNS – 1 pair – Secure your equipment on our lift with 1” x 6’ straps

16010

TOOL TRAY – Keeps tools organized and Handy

PART NO.

DESCRIPTION

QTY/UNIT

PART NO.

DESCRIPTION

QTY/UNIT

10819

Detent Clip

11250

Screw ¾-10 x 1¾

11008

Frame/Cylinder Pivot Shaft

11251

½ -13 Hex Nut

11052

Top Assembly

11252

Cam Bearing Retaining Ring

11167

Cylinder Assy & End Plate (Gray)

11253

Wheel Retaining Ring

11071

Cylinder Shaft Assembly (Gray)

11254

Frame Shaft Retaining Ring

14381

Valve Hose w/fittings

11255

Lock washer - ¾”

11123

Ramp Assembly (Gray)

11304

Cylinder Shaft Bushing

12937

Foot Valve Assembly (complete)

11305

Cylinder Shaft Seal

12887

Valve Stem Assembly

11306

Piston Seal

11177

Detent Bar

11308

Piston

11179

Frame Pivot Shaft

11315

Cam Roller Bearing

11183

Cylinder Repair Kit

11316

Cam Bearing Spacer

11248

½ x 1¾ Clevis Pin

11319

Cast Wheel

11249

1/8 x 7/8 Cotter Pin

11321

Track Roller Bearing

REPLACEMENT PARTS

09/10 14382

HANDY LIMITED WARRANTY

Handy Industries Division of Jadeim LLC, warrants to the original purchaser of this product, all parts to be free from defects in manu-

facture for a period of one (1) year from date of delivery. Notice of a defective part must be received in writing at Handy Industries with-

in one (1) year of purchase. All defective parts must be returned to Handy Industries and which, upon our examination any parts which

are defective in manufacture or workmanship, will be replaced or put in good operating condition. This warranty does not apply to dam-

age resulting from accident, improper installation, repair, operation or maintenance, negligence or neglect. THE COST OF SUCH

REPLACEMENT OR REPAIR SHALL BE EXCLUSIVE REMEDY FOR ANY BREACH OF ANY WARRANTY AND HANDY

INDUSTRIES SHALL NOT BE LIABLE TO ANY PERSON FOR CONSEQUENTIAL DAMAGE, OR INJURY, OR COMMERCIAL LOSS

RESULTING FROM ANY BREACH OF WARRANTY. HANDY INDUSTRIES MAKES NO WARRANTY OR MERCHANTABILITY,

MAKES NO WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND MAKES NO OTHER WARRANTY EXPRESSED OR

IMPLIED, INCLUDING IMPLIED WARRANTY ARISING FROM THE COURSE OR DEALING OR USAGE OF THE TRADE.

This manual suits for next models

Other Jadeim Lifting System manuals

Jadeim

Jadeim Handy B.O.B. 1500 AIR LIFT User manual

Popular Lifting System manuals by other brands

morse

morse 82H-124 Operator's manual

Braun

Braun NL955 Series Operator's manual

haacon

haacon 1889.10 quick start guide

Protekt

Protekt AT 252 instruction manual

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 operating manual

Nova Technology International, LLC

Nova Technology International, LLC NAS Series quick start guide

Genie

Genie Z-60/34 Operator's manual

Screen Technics

Screen Technics INTERFIT Vertical Up Lift instructions

Mortuary Lift

Mortuary Lift ULTIMATE 1000 instructions

Custom Equipment

Custom Equipment Hy-Brid 3 Series MAINTENANCE & TROUBLESHOOTING MANUAL

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Maintenance and troubleshooting manual

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 MAINTENANCE & TROUBLESHOOTING MANUAL

BERG

BERG BeNomic EasyLeaf Technical manual

Powermate

Powermate LiftGate LG-3 Installation & operation manual

Snorkel

Snorkel TM12 Series Operator's manual

Terberg

Terberg OMNIDEKA Translation of the original instructions

Harmar Mobility

Harmar Mobility AL625 Installation & owner's manual

Rotary

Rotary SPO16 installation instructions