Jaco EVO User manual
25-0215 Rev 01
1
TableofContents
SERIES PART NUMBERS...............................................................2
SYMBOL INFORMATION ..............................................................3
PRODUCT LABELING .................................................................3
GENERAL SPECIFICATION............................................................4
SAFETY RECOMMENDATIONS &WARNINGS......................................5
CARE,MAINTENANCE &WARRANTY .............................................6
INTEGRATION &OPERATION .......................................................7
OPTIONS ............................................................................. 10
LFP INTEGRATED BATTERY SYSTEM ............................................. 15
SET-UP AND CALIBRATION ..................................................... 16
SPECIFICATION.................................................................... 17
AGENCY CERTIFICATION........................................................ 18
BASIC TROUBLESHOOTING...................................................... 18
LFP HOT-SWAP BATTERY SYSTEM ............................................... 22
SYSTEM REVIEW &SET-UP ...................................................... 22
LFP HOT SWAP CHARGER ...................................................... 24
AGENCY CERTIFICATION........................................................ 25
MONITORING SOFTWARE....................................................... 25
BASIC TROUBLESHOOTING...................................................... 26
LFP BATTERY POWER SYSTEM MAINTENANCE................................. 28
2
Series Part Numbers
EVO PC/LCD Mobile Carts
EVO-20-NP – No Battery Power System Included
EVO-20-L250 – integrated 250Wh, LiFePO4 Battery
EVO-20-L500 – integrated 500Wh, LiFePO4 Battery
EVO-20-HS-– Hot-Swap Ready, No Batteries Included
EVO-20-HS-L408 – Hot Swappable (2) LiFePO4 Battery Packs
EVO Laptop Mobile Carts
EVO-10-NP – No Battery Power System Included
EVO-10-L250 – integrated 250Wh, LiFePO4 Battery
EVO-10-L500 – integrated 500Wh, LiFePO4 Battery
EVO-10-HS – Hot-Swap Ready, No Batteries Included
EVO-10-HS-L408 – Hot Swappable (2) LiFePO4 Battery Packs
Battery Charger - Only required for Hot-Swap Power Systems above
51-4218 – Dual Battery Fast Charger, table top or Wall Mount
Shown with two Hot-Swap LiFePO4 Battery Blades not included
3
Symbol Information
The following symbols are used within this Users Guide and / or on JACO products.
Symbol Meaning
Indicates that Caution should be taken.
Indicates Maintenance
Product Labeling
All JACO EVO Series Mobile Carts
The JACO EVO Series Mobile Cart is shipped with a P/N & Serial Number label for tracking and
service assistance. This label is located on the rear surface of the Top Assembly. The
information on this label is needed when contacting JACO Technical Service.
Indicates ATTENTION, consult the
accompanying documents
4
General Specification
Work Surface Height: 32.5" to 46.5"
Keyboard Height:
25.5" to 41.5"
Work Surface:
20" x 18"
Internal Laptop
or PC Storage:
16" x 14" x 3"
Casters:
4” Single Wheel, Front Locking
Wheel Base:
16" x 13" x 16"
Cart Weight:
Battery Weight:
EVO-10-NP with no options = 52 lbs.
EVO-20-NP with no options = 56 lbs.
L250 Power – 12 lbs.
L500 Power – 17 lbs.
Hot Swap Power – 20 lbs. with 2 batteries
Note: Additional counter weight may be added based
on total weight of added option including computer
system and LCD/LED Monitor.
5
Safety Recommendations & Warnings
WARNING: As with any mobile cart, caution must be taken
when pushing the cart through elevator doorways and over
thresholds. It is recommended that you lower the work surface to
waist high and position the cart so that only one-wheel contacts
the threshold at a time. This will help keep the momentum of the
cart moving forward and provide a safe transition.
WARNING: If your JACO Mobile Cart has a Drawer System option, limit weight per drawer to one-
pound, close drawers when moving and do not transport at more than a 5-degree slope.
WARNING:Your JACO Battery System is designed to operate as a system. Use only JACO Provided
components including replacement battery packs. Use of any non-approved Battery components may
result in damage and un-safe conditions.
WARNING: It is unlikely that you will experience any electromagnetic interference when using your
JACO Power System however if you notice any interruption or interference issues when using certain
computers or peripherals, notify your IT department before contacting JACO Service department.
WARNING: The JACO Power System contains lithium battery cells and as with all batteries, have
specific shipping restrictions that must be addressed. Please contact JACO Customer Service for
assistance before shipping any JACO product. It is the Shippers responsibility to follow all Federal &
State regulations when shipping lithium batteries.
WARNING: Do not open or dismantle the JACO Power System, note that there are no serviceable
parts. This equipment must be serviced by trained personnel.
A
dditional JACO Power System
important information:
* Use the Power System for the application
intended, to power a laptop or PC & LCD.
* Unplug the Power System from AC power to clean or if it is not working properly.
* Do not shor
t
-circuit the Power System
* Do not expose the Power System
t
o heat or fire and avoid storage in direct sunlight
* Do no
t
subject Power System
t
o mechanical
shock
* In the event of battery leakage, do not allow the liquid to come in contact with the skin or eyes, if
contact has been made, wash the affected area with water, seek medical advice.
* Always keep Power System Battery Packs clean and dry.
* Observe the plus (+) and minus (-) markings on the Power System.
* For disposing or recycling Power Blades, all Federal & State regulations must be followed.
* Refer to this manual for instructions, warnings and proper use.
* If your Power System will not be used for several months or longer, it is recommended that you
charge the batteries to full level and storing in a cool dry location.
* Retain this Users Guide and all original literature for future reference.
NOTE: Material Safety Data Sheets (MSDS) are available as needed, contact JACO
Support for more information.
6
Care, Maintenance & Warranty
All JACO products are designed and manufactured to provide many years of trouble free
operation. We recommend that you keep the product clean for optimal operation.
Most of the surfaces of your JACO product are finished using a
durable, antimicrobial powder coat finish. It is recommended that
the surface areas that are in contact with day to day use be cleaned
regularly. Always review the cleaning products that are being used
and verify that it is safe to use on the powder coat finish. In general,
a solution or wipe that is no more than 10% bleach, such as most
germicidal wipes used in hospitals, will be acceptable but it is recommended that you
consult with JACO Customer Service if you are not sure it is safe to use.
For the JACO Hot-Swap Battery Charger, there should be no reason to clean the inside
bay area but if required, make sure the unit is unplugged and a damp (not saturated),
less than 10% bleach wipe is used, allow ample drying time.
Your JACO Mobile Cart does not require any scheduled maintenance however it is good
practice to clean the casters and check that the Cart height adjustment is operating
correctly at least once a year. Please contact JACO Customer Service as needed for
more information in maintaining your JACO Mobile Carts.
At JACO, we stand by our products with a warranty plan that has you covered should
anything unexpected happen during the intended operation of the product. A copy of
this limited warranty is shipped with each product and explains the details of our
10/7/3 year limited warranty coverage.
HAVE A QUESTION?WE’RE HERE TO HELP.
CALL US AT 1-800-649-2278 OR VISIT JACOINC.COM/SUPPORT
JACO INC.140 CONSTITUTION BLVD,FRANKLIN MA, USA
7
Integration & Operation
Unpacking & Assembly:
Your JACO Mobile Cart is delivered on a pallet and unpacking is a two-person task, please plan
accordingly. Use caution when removing any additional containers that may have shipped on
top of the Mobile Cart pack. Once unpacked, there will be minimal assembly required
depending on the Mobile Cart model and options you have ordered.
Adjusting the JACO EVO Cart Height Position:
Your JACO Mobile Cart is height adjustable for proper ergonomics when used in a standing or
sitting position. To change the height, place the palms of your hands on the left and right sides
of the work surface and on the left side, squeeze the release lever by pulling it upward. This
will free the internal locking piston and will allow you to adjust the height of the Cart with
minimum effort. Release the lever when the cart is in the desired position.
Installing your computer system:
The JACO EVO Series Mobile Cart will support most PCs, Thine Clients, Laptops and All-In-One
8
computer systems and up to a 24” LCD/LED Monitor. Not all computer systems and LCD/LED
Monitors will fit, and some may fit but require too much power draw to operate with the
optional LiFePO4 Battery System. Contact your local Sales Representative or call JACO Support
to review any question you may have.
To install your PC or Laptop, unlock both key-locks at the rear of the top assembly as shown in
the photo below. Once unlocked, the top work surface can be pulled forward and removed
from the Cart.
Once the work surface is removed, the open bay area (shown on left below) is available for
installing your computer or laptop. Route all cables needed for proper operation before
installing the work surface and locking in place for security. Shown below is an example of a
small PC properly installed with all cables routed neatly and organized. If using a laptop
computer, simply open, place the laptop on the internal tray and allow the display to protrude
through the opening in the work surface.
Additional tips for proper computer installation:
SFF and Thin Client: insert inside the top bay so that the on/off power button is facing the side
9
opening. This will allow easy access for rebooting of the computer if needed.
Laptop: Open the laptop, place inside the top bay. Neatly rout the AC brick and cables into the
Top Bay with the power cord plugged into the internal power strip. Install the work surface so
that the laptop display protrudes through the opening, lock the work surface in place for
security.
All-In-One: The unit must have a 75mm or 100mm VESA pattern on the rear surface to mount
to the J1-20 Mobile Cart. The hardware to mount the All-In-One is provided.
It is highly recommended that you use the Velcro adhesive patches included with all Mobile
Carts inside the accessories kit to hold the PC, Thin Client, or Laptop in place inside the Mobile
Cart top assembly.
Installing LCD/LED Monitor:
Our PC/LCD Mobile Carts ship with the LCD Stand in place
but the optional LCD not attached. A Phillips Head or (if
added security is needed for the LCD) Torx Head driver is
needed to attach the LCD to the LCD Stand, 4 places. Both
Phillips and Torx screws are provided. It is recommended
that one person hold the LCD while a 2nd person inserts
the hardware.
Make sure all 4 screws are installed and tightened
properly. Check with JACO Support if the LCD/LED Monitor
is more than 8 lbs. for proper counter weight calculation.
With the monitor and stand installed on the Cart, the LCD
power and signal cables can be installed. Route both
cables down through the cable management area of the
stand as shown to the left. Pull the cables into the Top
Assembly and attach to the PC or laptop computer that
will be installed later.
Installing Keyboard & Mouse
When ordering your JACO Cart you have the option of including an integrated mouse and keyboard.
Table of contents
Other Jaco Outdoor Cart manuals
