iZone iWD3P User manual
Introduction
QuickView LED Display
Zone Thermostat LEDs
HVAC LED
Panel LED
Zone Damper LEDs
The iWD3P zoning system has been installed to improve your
comfort by regulating airflow to each zone to maintain the
comfort level you set on each zone thermostat. To improve
energy usage use higher cooling and lower heating
temperatures in spaces that are not being used regularly.
The multi-color LEDs help you determine the status of your
zoning system quickly without removing the cover on the
zoning panel.
Heating Request
Cooling Request
Heating
Normal Operation
Damper closed
Cooling
Minor Fault
Damper fully open
Fan ventilation
Fan ventilation
Major Fault
Damper partially open.
Red or blinking red.
Red or blinking red.
Blinking Green.
Off.
Green or blinking green.
Green or blinking green.
Blinking yellow.
Green.
Yellow.
Yellow or blinking yellow.
Off, red or blinking red.
Blinking green.
MENUMENU
CANCELCANCEL
NEXTNEXT
PDM Programming/Display ModulePDM Programming/Display Module
SAVESAVE
UP/YESUP/YES
DOWN/NODOWN/NO
eControls
Model iWD3P
HVAC PANEL ZONE DAMPERS
1 12 23 3
ZONE THERMOSTATS
Quick View
iWD3 Zoning Panel
Using PDM to Display Information
Vacant/Vacation Mode
The PDM is used to select vacation mode, display the
contractor’s and manufacturer’s name and telephone number,
error messages and the panel status.
MENU
MENU
NEXT
NEXT
SAVE
SAVE
PDM Programming/Display Module
PDM Programming/Display Module
CANCEL
CANCEL
UP / YES
UP / YES
DOWN / NO
DOWN / NO
eControls
iWD3P V102
Contractor
Info Y/N
In menu selections the available keys are shown. The
Cancel key can be used to exit the menu.
Momentarily pressing the MENU key displays the first
User menu selection.
No (N) key is used to navigate through the menu
selections or turn the Vacation mode off.
Yes (Y) key is used to navigate through the menu
selections or turn the Vacation mode on.
LCD display normally displays the manufacturer,
model number and version.
The CANCEL can be used to exit the display menu.
Pressing the SAVE key is used to turn the vacation
mode on or off.
The NEXT key is used to navigate through the menu.
1
1.
2
2.
3
3.
4
4.
5
5.
6.
6
8
7.
7
8.
Revised 9/15/13
Zone
Intelligent Zoning
User Guide
Model iWD3P
eControls
Vacation or Vacant mode can be used when the building or
home is going to be vacant for a period of time. The Zone1
thermostat will now control all the zones and the HVAC
equipment. Change the Zone1 thermostat to Hold mode if it is
a programmable thermostat and set energy efficient heating
and cooling temperatures.
The vacation or vacant mode can be controlled by the PDM on
the panel or by an SW01 Occupied/Vacant switch if it is
installed. The SW01 will override the PDM vacation/vacant
mode selection.
eControls
iWD3P V102
eControls
iWD3P V102
Vacation Off
Mode Y/NEXT/SAVE
Vacation On
Mode N/NEXT/SAVE
Vacation On
Mode N/NEXT
Vacation Off
Mode Y/NEXT
Vacation Off
Mode Y/NEXT
Manufacturer
Info Y/NEXT
Contractor
Info Y/NEXT
Display Error
Message Y/NEXT
Display Status
Y/NEXT
eControls, Inc.
949 916 0945 NXT
Best AC
555 111 2222 NXT
No Error
Message NEXT
SA Sensor Short
NEXT
MENU
MENU
Y
N
NEXT
Y
Y
Y
Y
NEXT
NEXT
NEXT
Turning Vacation Mode On Using the PDM
Turning Vacation Mode On Using the SW01
Model SW01
If Vacation Mode is On
Display Manufacturer Info
Display Contractor Info
Display Error Message
Display Status
Press the Menu key and the Vacation
screen is shown. Press the Yes key to turn
the Vacation mode on or press No to turn
the Vacation mode off. Press SAVE to
store your selection.
Set the switch to vacant at the end of the
day and the zoning panel will go into
Vacant mode using only the Zone1
thermostat to control the equipment. Set
the switch to Occupied mode at the start of
the day.
The Vacation On screen will remain
displayed when in Vacation mode. Press
the No key to turn the Vacation mode off
and press the SAVE key to store your
selection.
Press the MENU key and then the NEXT
key to display the Manufacturer Info screen
and then press Yes to display the
information. The manufacturer’s name and
telephone number is displayed. Press
NEXT to display the Display Contractor
Info screen.
Press Yes to display the contractor
information. The contractor’s name and
telephone number is displayed if it was
entered at installation. Press NEXT to
display the Display Error Message screen.
Press Yes to display any error messages.
The examples show no error messages
and a short in the supply air temperature
sensor. Press NEXT to display the Display
Status screen.
Press Yes to display the Display HVAC
Status screen. Press NEXT to return to the
main menu.
Rev 8/22/13
OCCUPIED
VACANT
Display HVAC
Status Y/NEXT
Display Zone
Status Y/NEXT
Display Damper
Status Y/NEXT
Display Sensor
Temps Y/NEXT
Heating Stg1
NEXT
Zone 1 Heat1
NEXT
Damper 1 Open
NEXT
SAT 134 ODT 42
NEXT
Damper 2 Closed
NEXT
Damper 3 Open
NEXT
Damper 2 16%
NEXT
Zone 2 No Call
NEXT
Zone 3 Heat1
NEXT
Y
Y
Y
Y
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
Display HVAC Status
Display Zone Status
Display Zone Damper Status
Display Sensor Temperatures
If Modulating Dampers Are
Used for Bypass
Press Yes to display the HVAC status. The
example shows the HVAC system is in first
stage heating. Press NEXT to display the
Display Zone Status screen.
Press Yes to display the status of each
zone thermostat. The example shows
Zone1 requesting stage 1 heating, Zone2
with no request and Zone3 requesting
stage1 heating. After displaying the last
zone thermostat, Press NEXT to display
the status of each zone damper.
Press Yes to display the status of each
zone thermostat. The example shows
Zone1 damper open, Zone2 damper
closed and Zone3 damper open. After
displaying the last zone damper, Press
NEXT to display the Display Sensor Temps
screen.
Press Yes to display the sensor
temperature readings if your system uses
sensors. The example shows the system
o
Discharge Air Temperature is 134 F and
o
the Outdoor Temperature is 42 F. Press
NEXT to return to the main menu.
If modulating dampers are being used
for bypass, the screen will shown the
percent a damper is partially open.
eControls, Inc.
26072 Merit Circle #110 / Laguna Hills, CA 92653
949-916-0945 Fax 949-458-8502 www.iZoneUS.com
eControlseControls
Limited 5-Year Warranty
The 5-year warranty is limited to the repair or replacement of
defective product due to parts failure or defective workmanship.
Table of contents
