ITE IT9500 Series User manual
ccHDtv Configuration Tool (USB UART kit) IT9500 Series
2/24/2015 0Copyright 2012-2014, ITE Technologies, Inc
ccHDtv Return Channel User Guide
(USB UART kit)
Revision Log:
ITE Tech. Inc.
Easy HD Expressway
® ®
Revision
Date
Author
Remarks
1.0
2013/09/17
Ryan
Initial Release
1.1
2014/03/06
GUI version
1.1
2014/3/14
Chapter 3.2
1.2
2014/9/17
Tool update
2014/12/31
USB dongle kit
2014/01/27
USB UART kit
1.3
20150224
Jeff
Configure the video stream
ccHDtv Configuration Tool (USB UART kit) IT9500 Series
2/24/2015 1Copyright 2012-2015, ITE Technologies, Inc.
Table of Contents
1. Introduction............................................................................................................3
2. Installation..............................................................................................................4
2.1 Install USB UART Dongle .......................................................................4
2.2 Install Config Tool ReturnChannelGUI....................................................5
3. Configuration Tool (Return Channel GUI) Usage.................................................7
3.1 Launch the config tool kit.........................................................................7
3.2 Initialization..............................................................................................7
3.3 Basic Settings............................................................................................9
A. Imaging Settings .....................................................................................10
B. Bit Rate Settings .....................................................................................10
C. Channel Frequency and Bandwidth Settings..........................................10
3.4 Set Transmission Parameters ..................................................................12
3.5 Set Single Stream Output........................................................................16
3.6 Configure Encoded Video Stream Frame Size........................................16
3.7 Set Other Configurations ........................................................................17
ccHDtv Configuration Tool (USB UART kit) IT9500 Series
2/24/2015 2Copyright 2012-2015, ITE Technologies, Inc.
Table of Figure
ccHDtv Configuration Tool (USB UART kit) IT9500 Series
2/24/2015 3Copyright 2012-2015, ITE Technologies, Inc.
1.Introduction
This document describes how to use Return Channel test kit and USB UART dongle
to control ccHDtv DTV CAM in PC Windows environment.
USB UART dongle,
If you use receiver dongle/board with return channel feature to configure the camera,
please refer to the document “Config Tool with RC receiver kit (Return Channel GUI)
User Guide”,
USB receiver dongle or board with return channel feature,
The following picture shows the profile of the environment setup with USB UART
dongle.
USB UART
Dongle
DTV CAM
(DC-099BB)
PC Windows
ccHDtv Configuration Tool (USB UART kit) IT9500 Series
2/24/2015 4Copyright 2012-2015, ITE Technologies, Inc.
2.Installation
2.1 Install USB UART Dongle
You may connect the UAB UART to a Laptop PC.
On most Windows platforms, the driver will be installed with in-box driver
automatically.
However, if Windows prompts to install driver for the new device, please run
“PL2303_Prolific_DriverInstaller_v1.7.0.exe”, which can be found in the folder
“\PL2303_Prolific_DriverInstaller_v1.7.0”
If the device driver is installed well, there will be a new Com Port device, shown in
Windows Device Manager.
The com port assignment may vary depending on the PC configurations. In the
following example, COM5 is assigned.
ccHDtv Configuration Tool (USB UART kit) IT9500 Series
2/24/2015 5Copyright 2012-2015, ITE Technologies, Inc.
Note: the wirings between the USB dongle and camera UART port,
USB dongle RXD—Green—Camera UART TXD
USB dongle TXD—White—Camera UART RXD
USB dongle GND—Black—Camera UART GND
2.2 Install Config Tool ReturnChannelGUI
In the folder \ReturnChannelGUI, click on “Setup.exe”to run the installation.
After installation, you should find the kit in the folder ITE of the start menu.
ccHDtv Configuration Tool (USB UART kit) IT9500 Series
2/24/2015 6Copyright 2012-2015, ITE Technologies, Inc.
ccHDtv Configuration Tool (USB UART kit) IT9500 Series
2/24/2015 7Copyright 2012-2015, ITE Technologies, Inc.
3. Configuration Tool (Return
Channel GUI) Usage
3.1 Launch the config tool kit
When the camera boots completely (the video LED on the RF board PCB is on), click
on “ReturnChannel Tool Kit”in the start menu.
3.2 Initialization
It may prompt the following messages. Please ignore it and click on OK to continue.
Video LED
ccHDtv Configuration Tool (USB UART kit) IT9500 Series
2/24/2015 8Copyright 2012-2015, ITE Technologies, Inc.
Specify the com port of the USB UART dongle for both Rx and Tx, and then click on
“Open”.
(The com port assigned can be found in device manager, as described in 2.1)
Click on “Get All Device”and wait for a few seconds.
If the camera is connected, the camera ID will be showned and checked, as shown
below.
ccHDtv Configuration Tool (USB UART kit) IT9500 Series
2/24/2015 9Copyright 2012-2015, ITE Technologies, Inc.
Fig 3-1 Camera found and connected
3.3 Basic Settings
Basically, most of the configurations can be set in the basic setting menu.
Table of contents
