Isotech ICM A7 User manual
ISO-TECH ICM A7
ELECTRICAL TESTER
INSTRUCTION MANUAL
INTRODUCTION
1-1 Unpacking and Inspection
Upon removing the A7 open jaw clamp meter from its packing, you should have the following items :
1. A7 open Jaw Clamp meter.
2. Instruction manual.
1-2 SAFETY
Review the following safety precautions to avoid injury and prevent damage to this product or any products
Connected to it. To avoid potential hazards, use the product only as specified.
#CAUTION. These statements identify conditions or practices that could result in damage to the equipment or
other property.
#WARNING. These statements identify conditions or practices that could result in personal injury or loss of life.
Symbols on the product
#Refer to manual 1Double Insulated □Battery
Specific precautions
1. To avoid personal injury, do not apply any voltage or current to the product without the covers in place.
2. To avoid injury or loss of life, do not touch the metal probe tips while they are connected to a voltage source,
probe tip sleeves are supplied.
3. To avoid electric shock, do not operate this product in high temperature or high humidity environment.
4. Do not use the tester if it or its test leads appear damaged, or if you suspect that the tester is not operating
properly.
5. Never apply more than the rated voltage, as marked on the tester, between a terminal and earth ground.
1-3 FRONT PANEL OVERVIEW
Refer to figure 1 and the following numbered steps to familiarize yourself with the meter’s front panel controls and
connectors.
1. Digital Display — The liquid crystal display (LCD) is a 3 1/2 digit display (maximum reading of 1999), with
autopolarity and decimal point indicators.
2. Measurement Function Dial — Rotate the function dial to select V%, V', Ω□and A%function.
3. Display Hold — To hold the reading on the display, press and release HOLD .
To exit the display hold mode, press and release HOLD again.
4. Sensor Zone — Place conductor anywhere within the sensor zone (shades area shown as Figure 2).
Figure 1
4
1
3
2
5
SPECIFICATIONS
2-1 General specifications
LCD display digits : 3 1/2 digit large scale LCD readout.
Display count : 2000 count.
Measuring Rate : 2.5 times / sec.
Overrange display : “OL” is displayed for “A” and “Ω” functions, shows the real value for “V” function.
Low voltage indicator : □is displayed. Replace the battery when the indicator appears in the display.
Automatic power off time : Approximately 13 minutes after power on. To resume operation, turn the tester off,
and then on again.
Power Requirement : Single 9V battery (NEDA 1604, JIS 006P or IEC6LF22).
2-2 Enviromental conditions
Indoor Use.
Calibration : One year calibration cycle.
Operating Temperature : 0℃~ 30℃(≦80%RH), 30℃~ 40℃(≦75%RH), 40℃~ 50℃(≦45%RH)
Storage Temperature : -20℃~ + 60℃(below 80% RH) with battery removed.
Temperature Coefficient : 0.2 x (Specified accuracy) / , < 18℃, > 28℃.
Operating Altitude : 2000m (6562ft)
Battery Type and Life : ALKALINE PP3, 9V 250 hours.
Overvoltage Category : IEC 1010 600V CAT.Ⅲ.
Pollution Degree : 2 Class Ⅱ
Shock Vibration : Sinusoidal vibration per MIL-T-28800E (5Hz to 55Hz, 3g maximum).
2-3 Electrical Specifications
Accuracy is ±(% reading + number of digits) at 23℃±5℃< 80%RH.
1. Voltage
Function Range Resolution Accuracy Overload Protection
V%600V rms 1V
±
(
1.5% + 3 di
g
its
)
40Hz
~ 500Hz 600V rms
V'600V 1V ±(1.0% + 2 digits) 600V rms
Input impedance : 1MΩ// less than 100pF.
2. Resistance & Continuity
Function Range Resolution Accuracy Overload Protection
Ω□2000Ω1Ω±(1.0% + 2 digits) 600V rms
Max. Open Circuit Voltage : 3V
Continuity check : Internal sounder activates if the resistance of the circuit under test is less than 25Ω. It will
then turn off if the resistance is increased beyond 400Ω.
3. AC Current
Function Range Resolution Accuracy Overload Protection
A%200A 0.1A
±
(
3.0% + 3 di
g
its
)
45Hz
~ 66Hz 200A
* Adjacent conductor influence : <0.05 A/A
OPERATION
This instrument has been designed and tested in accordance with IEC Publication 1010, Safety Requirements for
Table of contents
Other Isotech Test Equipment manuals
Isotech
Isotech IRT2310 User manual
Isotech
Isotech Quick-Cal Series User manual
Isotech
Isotech PEGASUS PLUS 1200 Series User manual
Isotech
Isotech LCR 1705 User manual
Isotech
Isotech Saturn 878 Operating instructions
Isotech
Isotech ITS-90 Operating instructions
Isotech
Isotech PHTC-783 Mounting instructions
Isotech
Isotech IIT 1500 User manual
Isotech
Isotech MEDUSA 510 Series Operating instructions
Isotech
Isotech 875 Operating instructions
