ISLABIKES Joni 20 User manual
www.islabikes.co.uk
Joni 20 & 24
Owner’s Manual
Joni 20/24
1. Brake pads
2. Saddle
3. Seatpost
4. Seatpost clamp
5. Saddle clamp
6. Stem bolts
7. Rim
8. Spokes
9. Tyres
5
4
6
3
8
7
12
10
13
14
15
16
2
1
9
11
Setting up your Islabike
10. Chain
11. Rear derailleur
12. Cassette
13. Frame
14. Fork
15. Cranks
16. Pedals
www.islabikes.co.uk
17. Brake levers
18. Stem
19. Headset
20. Headset spacers
21. Headset adjuster bolt
22. Handlebars
23. Gear shifters
17
23
19
20
22
21
18
Joni 20/24
Step 1 of 7
Remove front wheel packaging
and unhook the front brake
1. Remove front wheel protection packaging.
2. Remove fork plastic protection packaging.
www.islabikes.co.uk
3. Unhook front brake hinge.
Step 1 of 7
Remove front wheel packaging
and unhook the front brake
Joni 20/24
Step 2 of 7
Securing front wheel
1. Put front wheel into the fork.
Ensure quick release (QR) lever
is not on gear side. Check this
matches rear.
Ensure QR skewer springs
orientation is correct.
2. Hold QR lever in fully ‘open’
position and turn nut clockwise.
Do not fully tighten nut.
Tighten
Correct
Incorrect
www.islabikes.co.uk
The QR lever should start to feel tight at 90 degrees as you close
– if it is too tight or too loose can adjust by holding lever ‘open’
again and turning nut.
Check front wheel is correctly installed by lifting the handlebar and
holding the wheel at the fork. Firmly push from side to side.
Ifthereisnomovementthewheelisttedcorrectly.
3. Clamp the QR lever to fully ‘closed’ position towards rear of bike.
Step 2 of 7
Securing front wheel
Joni 20/24
Step 3 of 7
Re-connecting front brake
1. Re-connect front brake by hooking the silver metal cable hose
(noodle) back into the hinge. Check this matches the rear.
2. Pull the right brake lever on to check brake works correctly.
Both brake blocks should contact the rim.
Check front brake operates correctly before allowing child to ride.
If unsure contact our technical support team
www.islabikes.co.uk
Step 4 of 7
Handlebar set up
1. Turn handlebars clockwise and align with front wheel
2. Tighten both stem bolts clockwise max. 7Nm
Failure to correctly tighten stem clamp bolt may result in serious
injury or death. If in doubt, please consult our technical support
Do Not
Tighten
1. Turn
2. Tighten
Joni 20/24
Step 5 of 7
Pedal installation
All pedals are supplied in pairs with a specic left and right pedal.
This is to prevent the pedals from undoing as you turn the cranks
with your feet.
Please ensure that you have identied the left and right pedal before
installation to avoid damaging the crank arm.
If these features are missing, another tip is to check the Islabikes logo.
When standing at the back of the bike looking towards the front, the
Islabikes text on the pedal should be in the correct orientation to read:
Many of our pedals have the following
features on the pedal axle to help you
identify the left and right pedals:
LH pedal has line marking on axle.
Incorrect
Correct
L/R
This manual suits for next models
1
Table of contents
Other ISLABIKES Bicycle manuals
ISLABIKES
ISLABIKES elcons eJimi User manual
ISLABIKES
ISLABIKES Icons Jimi User manual
ISLABIKES
ISLABIKES Rothan User manual
ISLABIKES
ISLABIKES eJoni User manual
ISLABIKES
ISLABIKES luath pro series User manual
ISLABIKES
ISLABIKES Beinn User manual
ISLABIKES
ISLABIKES elcons eJanis User manual
ISLABIKES
ISLABIKES Beinn 20 Pro Series User manual
ISLABIKES
ISLABIKES Beinn 29 User manual
ISLABIKES
ISLABIKES Creig Series User manual
